Golf MK5 1K1 Suspension Overhaul
HTML-код
- Опубликовано: 24 фев 2022
- This video was preformed on a 2008 Volkswagen Golf 1K1 1.6L BGU engine.
Repair Manual: shrsl.com/4fjft
20% OFF Sitewide Code: ZAKI20
Parts:
Control arm: AISIN JTAVG-008L | AISIN JTAVG-008R
Ball Joints: SuperPro Roll Control Ball Joints TRC0003
Control arm bolts: N10141003
N91039802 amzn.to/33WXZji
N10579702
Engine mount: LEMFÖRDER 31034 01 | LEMFÖRDER 33143 01
Engine mount bolts: N90596906
Stub axle/ knuckle assembly: MAPCO 107757/1
Wheel Hub: ALANKO 10342988
Tie Rod End:
(1K0423812E-M) FEBI BILSTEIN 26097 amzn.to/3LVJmh8
(1K0423811E-M) FEBI BILSTEIN 26096 amzn.to/35nppz3
Drive Shaft: GSP 203318
Wheel Hub Centric Rings: amzn.to/3pEgssD
Lug Bolts: VW WHT002437 amzn.to/3pcXBob
Tools:
17mm lug nut socket: amzn.to/3nxtg2J
Impact Wrench: amzn.to/3A1wa4Z
27mm Impact Socket Deep: amzn.to/3Iu5M7i
Pick Set: amzn.to/3Cik6LT
Drive Socket Set: amzn.to/3HgtHW5
Socket Set: amzn.to/3oo60E8
Bungee Cord: amzn.to/3HnyyVI
Socket Adapter: amzn.to/3sntZ9H
Drive Impact Socket Set: amzn.to/3HfG5WB
Pry Bar Set: amzn.to/3vi9vRr
Mallet: amzn.to/3slYdtw
Socket Set M-Type: amzn.to/35sKuYK
Breaker Bar: amzn.to/3sntnAW
Wrench Set: amzn.to/3sj37rh
Ball Joint Separator: amzn.to/3phQ07N
Bosch Compact Drill: amzn.to/3s0bsgE
Hex Key Wrench Set: amzn.to/3JQo4Q4
Strut Spreader Socket: amzn.to/3LYmAp7
Socket Extension: amzn.to/3kwmybW
Trim Tool: amzn.to/3Dq9QCE
Heat Gun: amzn.to/3hfIfef
Torque Wrench: amzn.to/3wGZ5JT
Anti-Seize: amzn.to/3JZsl3J
Silicone Grease: amzn.to/3M2KsrG
RhinoRamps: amzn.to/3bccjDZ
Some of links above are affiliate links, which means I'll earn a small commission if your make a purchase from my links which will help out this channel! 🙏
I am not a certified or professional mechanic. This video is for entertainment purposes only. Zaki Garage assumes no liability for any actions performed by the viewer as a result of the information contained in this video. 
Авто/Мото
![How to change rear suspension arm / rear control arm on VW GOLF 5 (1K1) [TUTORIAL AUTODOC]](http://i.ytimg.com/vi/1O4vMzjKS_s/mqdefault.jpg)
Cat in a video, count me in 😀
Nice work! Good Job! Easter Egg at 25:00 😂 The CAT!!!
Superb video guide. Thanks a lot for your work.
Thanks bro
Mate, this is ASMR
Love your editing
Thx
Very good video
Great video and job :)
thx mate
This is a great watch, I'm planning on doing similar work but not quite as extensive. Just poly bushes, new drop links and ball joints. Glad I seen this so I'm not gonna be surprised about getting the gearbox out the way for that control arm though. Bet it feels absolutely solid to drive now!
Thx 🙏glad you enjoy it. Yeah, the control arm bolts were a real surprise for me the first time, took me weeks stuck on them. It drives a lot better now and feels solid but unfortunately when to a bad alignment shop, and still haven't had time to go get a better alignment. And still have more suspension parts planned for it in the future.
You could probably aline the wheels better yourself - if you can do this job wheel alignment should be easy for you...
Love the drill trick to clean the caliper pins!
@Kellier1916 you're probably right, will have to give the alignment a try next time 👍🏻. Wish I had thought of the pin cleaning before, been wasting so much time and effort cleaning them manually in the past
nice super sweet
Big like
Much appreciated 🙏🏼
so lovely, no rust :) unlike mine :(
Yeh sorry, I know its cordless. Cheers
hello from slovakia, for future try it aluminum arm and bearing housing it is best from your car
Thanks, will consider it for next time
Great vid! Can i ask why you only changed the hub & driveshaft on one side?
Thx, changed the whole steering knuckle on the left side since one of the bolt holes for the caliper was stripped. The steering knuckle came as a kit with a new hub so replaced it all. Also, changed the axle on the left side since the boot on it was cracked and leaked the grease all over the left side. The axle on the right side looked good at the beginning but I think I'll replace it too in the future after seeing its condition. Reason for changing only the hub on the right side is a stripped wheel bolt hole.
Great Vid, tks, question what model Milwaukee air wrench have you used here
Thx . Its not an air tool, just an electric impact. Got it linked in the vid description. amzn.to/3A1wa4Z
👍
Will be doing this same thing to my mk4 jetta vr6 both front and rear suspension with rear axle beam included... how much would it cost at a mechanic
This project cost me around 1400$ in parts, shipping, and the few extra tools I had to buy. For labor you'll need to add up all the individual fixes hour rates, and multiply it by your area's mechanics rates, and it would be a lot i'm guessing
@@ZakiGarage got a quote for 1200$ from a local shop. Thanks for the reply
Not a bad quote👍🏻 good luck
Never used wd-40 as a rust penetrant. However, freeall works the best ive ever found. Free plug. That wd-40 is just making a mess.
No it's not, WD40 is above all greases. Maybe Your product is fake😂
How much where all your parts? Would you know how much this would be if a workshop did this?
All the parts cost me around 1400$. Hard to tell how much it will cost at a shop.
thanks for the reply, planning on overhauling my Scirocco's suspension @@ZakiGarage
That's a sweet car 👌. Am also planning on a round 2 of suspension fixes hopefully soon
Good Luck :) its 2.0TSi absolutely in love with it, 2010 only 40k miles on the ODO full VW service history but its spent the last 3yrs by the uk coast so the suspension could do with a few upgrades :) can't wait to see your round 2 @@ZakiGarage
@@fjung123 Thx , looks like you have a great model and well taken care of. Keep up the great work taking care of it 👍
Kitty makes everything better 🐱
I wish you lived in Kenya.
I'm sure there are better people than me in kenya to work on cars 👍🏻
Why Brenda
your forgetting lower arm needs tightening on the deck not at full droop
No worries, it was done @ 26:40