great content Jesse, but how do you troubleshoot that what is causing the face id to act like this, because even after programing the dot projector i still get errors, such us lower the iPhone, get close to the phone, try setting up face id later, sometimes it just doesn't say anything , and im confused what is causing it, i use clone-dz03 for dot projector, i appreciate the help for the repair community.
Amazing u r are so detailed in explaining . So this mean if some how the original flex gets damage we can recover the FI. And if this process can be done on 12 and 13 ?Thanks
I was working on iPhone XS Max Face ID, but screwed up 😢 I was supposed to short the mosfet, but instead removed the capacitor and cut of the golden wires next to the capacitor and also the wires of the led light. I managed to solder the wires back and installed a capacitor back. Now if I test it with the i2c v8i it passes the test, but on the iPhone it doesn’t do anything. No Face ID, no portrait photos. Any steps suggested to take?
Hey brother...i have also a question for u i think as my knowledge in this flex we have to 1st jailbreak the iphone...u done it without jailbreak....is that possible to use jc flex without jailbreak and u directly unbind from the Nand...????? Pls reply....this method is support for all models like x to 12pro max?????
Nice but did u try to without opening nand jc new update has ability to unbind the earspeaker flex without removing nand !! I think !! That's the option for fiting unbind option for if u make on video for me please!! Cause i am curiouse about it
Another great video Jess and good to see you back online. I didnt know the P13 could do Iphone 7+ nands? When using the Query disk section of JC software and type in the nand spec (THGBX5G8D4LLDXG) it clearly states that the p13 can read/write this nand., which is in the iphone 7+. Am I right or reading the software wrong?
I have an iPhone X that came in for repair. The phone was shorted on vdd boost. And I was able to remove the short. But now when I try to on the phone on dc power supply, it get stuck on 70mah. Would appreciate some useful help here
@@VCCBoardRepairs that data is stored on the syscfg layer on the original nand. So you say that if the original nand is dead, you stick there a new nand, re-flash and then have all data back?! Why then you would need a gsx service to recover a missing Wi-Fi or bt MAC address?
This solution is proven to work. You install a new NAND onto the device. Restore Pull NAND and scan it Then program it with the data it recovered And it will work No need to pay for GSX service anymore
@@VCCBoardRepairs this is great, something I wasn’t aware of… unfortunately I do not have a p13, I have the Mijing p12 and I doubt that has that scanning feature
I really really love the video but I have a couple questions, I’ve been watching your channel for a while and I have to say you make great videos and I’m learning from you, now my questions are Do we need to unbound the nand to make earpiece replacement work? Or we only have to unbound if the earpiece speaker is not the original? Number 2 I recently ordered tools I saw on your videos, I have v1se and Irepair dfu p10, but I learned that p10 only support old phones to iPhone X, can I use another nand programmer to unbound and activate with v1se? Or I have to use the jc p13, cos I was planning on getting a different brand, that support up 13 pro max nand programing, p13 is quite expensive with my current situation Number 3 Is it compulsory we use the Jc earpiece speaker flex? Or we can just use another, maybe from a broken phone or a different brand in the market
1. Yes you have to unbind 2. I don't know if other programmer works with JC method 3. No, only JC flex works with JC tools. You can't use another original. V1S won't detect it.
@@VCCBoardRepairs I’m so happy for you answering my questions, thank you so much and again I have one more question, i saw a video where Rewa used jbox and v1se, without unbinding
@@VCCBoardRepairs ihave iphone 13 pro max no imei on *#06# but it was showing no sim when you turn on/off flight mode so i swapped lover board but problem still same when i used 3utools and looked for baseband version build and all needed for perfect baseband everything is fine so i updated phone before and after swapping lower board but problem is still same do you have any other suggestion for repair it ?
brow this information is a little wrong, to unlock unbide you no longer need to remove the nand, it is also possible to do the same procedure using i2c, both methods without removing the nand
really people, who buys an apple that has been bitten into!!! the makers of the telephone destroy your expensive device through updates and you remain so calm because of that.. wow 😂😂😂😂😂
Great to watch a maestro at work… appreciate your gloves too, keeping the interior factory pristine.
Thank you so much sir…Very good information this Video.❤four you From Bangladesh 🇧🇩
You are most welcome
Nice work Jesse, you always make it look easy
Thank you!
This man on a DIFFERENT LEVEL
Thank you! Appreciate the support!
HOLY MOLY !!! DUDE THANK YOU !! , bro ive been having both things but i didnt know this , u a boss thank you
Glad I could help
Great video, thanks you!
Btw. Can you tell what kind of iPhone models need to remove nand to unbind wifi?
A9 based devices and newer, like iPhone 6S and newer.
great content Jesse, but how do you troubleshoot that what is causing the face id to act like this, because even after programing the dot projector i still get errors, such us lower the iPhone, get close to the phone, try setting up face id later, sometimes it just doesn't say anything , and im confused what is causing it, i use clone-dz03 for dot projector, i appreciate the help for the repair community.
You are explaining perfectly
Thank you! Appreciate the support!
Ek number bhai jan from India ❤
I don’t have money to join rewa academy …am getting a bit tutoring from your channel thank you ..but I wish I can get more
Thank you very much!
Is it same method pour iPhone 12? Unbind will not broke wifi ? Thanks !
yes
Yeee, I was waiting for this video 😁
Awesome 🙌
Amazing u r are so detailed in explaining . So this mean if some how the original flex gets damage we can recover the FI. And if this process can be done on 12 and 13 ?Thanks
Correct.
Only works up to iPhone 12 series. Not 13.
13 doesn't even have a flood Illuminator
Hi you need Exactly the JCID Sensor flex or others work too `?
you need JC flex for this to work, as mentioned in the video
thank you jesse this toturial was great, can this v1se progmmer tell if the flex is the original or not?
I don't think it can
I was working on iPhone XS Max Face ID, but screwed up 😢
I was supposed to short the mosfet, but instead removed the capacitor and cut of the golden wires next to the capacitor and also the wires of the led light. I managed to solder the wires back and installed a capacitor back. Now if I test it with the i2c v8i it passes the test, but on the iPhone it doesn’t do anything. No Face ID, no portrait photos. Any steps suggested to take?
in newer IOS versions you have to reflash, otherwise it won't detect the stuff. You could give that a try
Did we still need to unbind the nand if we want to do same thing on 12 series
Yes you can do it without NAND removal
Watch my new video on my channel
you have a great setup to record your videos, do you record everything at the same time then you put everything together with Multicam in FCP?
I record it "live". just 1 video file.
brilliant as always mate
Thank you! Cheers!
Hey brother...i have also a question for u i think as my knowledge in this flex we have to 1st jailbreak the iphone...u done it without jailbreak....is that possible to use jc flex without jailbreak and u directly unbind from the Nand...????? Pls reply....this method is support for all models like x to 12pro max?????
What if we want the True Tone back how are we going to do that at least the True Tone has already been unbound in JCID
it will return when you replace the ear speaker flex with the JC Flex
best video tutoriol boss...i from malaysia
Hi Jesse, great video again man. I was wondering if you could do a video about the P13 ? Thanks and have a good day
This video covers it.
What else do you need to know?
Hey Jesse, is this necessary? Your other video shows you just swapping the chip on the speaker flex. Is this for a different problem?
Yes. It's for when you don't have the original flex
Thank you so much for detailed video
Knowledge able video sir thanks
So nice of you
how long did it take you to do all this?
and how much do you charge to get something like this done?
hard to say. i recorded this across several weeks.
but if i were to do it from scratch, maybe 1-2 hours total
Love for you This video meant a lot to me
Thank you!
Hlw sir
Which JBox Use for Unbind And Jailbreak Iphone X to 14PM if Any Please Reply
i'm not sure
42:02 what do you think about qianli iatlas if you can try them or make a video aboit them they sould help in this type of situations
i have them, but haven't used them much.
Nice but did u try to without opening nand jc new update has ability to unbind the earspeaker flex without removing nand !! I think !! That's the option for fiting unbind option for if u make on video for me please!! Cause i am curiouse about it
Not yet! I am curious about that too!
Excellent work 👌
Super , I like it . Good job
Its possible use p11f or i must use the P13?
Only JC P13
@@VCCBoardRepairs How about PRO1000S with BGA110 Module? Also not possible?
No
Is it possible to use none jcid flex?
No. I tried
Very nice job.
Thank you!
Great job ❤
Thank you very much!
Another great video Jess and good to see you back online. I didnt know the P13 could do Iphone 7+ nands? When using the Query disk section of JC software and type in the nand spec (THGBX5G8D4LLDXG) it clearly states that the p13 can read/write this nand., which is in the iphone 7+. Am I right or reading the software wrong?
JC P13 can read and write NAND through Purple mode, not the socket
I have an iPhone X that came in for repair. The phone was shorted on vdd boost. And I was able to remove the short. But now when I try to on the phone on dc power supply, it get stuck on 70mah. Would appreciate some useful help here
Post in my group
Https://www.vccboardrepairs.com/vcc-fb-group
@@VCCBoardRepairs I did
Sir I have iPhone 13 itune error 4013
What is the problem? please help me
Do you have solutions for iOS 17.3.1???
It works with all iOS
Is there a way without raising the nande? ios17. 3
Yes, brushing with jc repair assistant
All the clips that I have received are explained via v1se only via iOS 16
I lost the original sensor of the device
And the client device has ios17. 3.1
great explanation.
Glad you think so!
JC P13 ultimate box PCIE Nand programmer for iPhone dot projector data recovery, Nand data code query, iOS device Nand error repair or expansion, WiFi unbinding, DFU purple screen repair without disassembling, ect.
Hi sir I ordered iPhone 11 motherboard with face Id but they send only motherboard so is it possible to reprogramming and use new face id
Hi you need front camera sensor flex (With IR camera lattice sensor ) if you have you fix that with this method 😊
^^ Correct answer
Thanks
No problem
Props as always! But goddamn, what a series of steps Apple makes you do just to swap a damn speaker
That's apple for you. Trying to take away right to repair
technically, i'm not swapping the speaker, i'm swapping the Face ID sensors
Is this possible with p14pro?
yes but you have to use i2c flex
thanks Boss
Welcome
great job
Be careful when removing the NAND. If you apply too much heat, it could float the CPU and other components on the other side of the board.
Of course. That's literally what I mentioned in the video
ممكن كيف الاستخراج مع البرمجه مافتهمت زين
What days you say at 29:42? I really doubt that….
Your doubts are wrong. I've recovered original SN WiFi BT this way many times
@@VCCBoardRepairs that data is stored on the syscfg layer on the original nand. So you say that if the original nand is dead, you stick there a new nand, re-flash and then have all data back?! Why then you would need a gsx service to recover a missing Wi-Fi or bt MAC address?
This solution is proven to work.
You install a new NAND onto the device.
Restore
Pull NAND and scan it
Then program it with the data it recovered
And it will work
No need to pay for GSX service anymore
@@VCCBoardRepairs this is great, something I wasn’t aware of… unfortunately I do not have a p13, I have the Mijing p12 and I doubt that has that scanning feature
It probably does. But you'll have to check with them about that
Use I2c programer without removing nand
sadly, i recorded this weeks ago, before I knew about i2c solution
I really really love the video but I have a couple questions, I’ve been watching your channel for a while and I have to say you make great videos and I’m learning from you, now my questions are
Do we need to unbound the nand to make earpiece replacement work? Or we only have to unbound if the earpiece speaker is not the original?
Number 2
I recently ordered tools I saw on your videos, I have v1se and Irepair dfu p10, but I learned that p10 only support old phones to iPhone X, can I use another nand programmer to unbound and activate with v1se? Or I have to use the jc p13, cos I was planning on getting a different brand, that support up 13 pro max nand programing, p13 is quite expensive with my current situation
Number 3
Is it compulsory we use the Jc earpiece speaker flex? Or we can just use another, maybe from a broken phone or a different brand in the market
1. Yes you have to unbind
2. I don't know if other programmer works with JC method
3. No, only JC flex works with JC tools. You can't use another original. V1S won't detect it.
@@VCCBoardRepairs I’m so happy for you answering my questions, thank you so much and again I have one more question, i saw a video where Rewa used jbox and v1se, without unbinding
I haven't seen that video so I don't know
@@VCCBoardRepairs ok thank you
nice bro ❤
Thanks 🔥
I did this week ago its worked but today i did same for iphone 13 lattice data recovery isn’t worked
Doesn't work for 13 series
@@VCCBoardRepairs does it work for 12 series i have an 12 pro ear speaker flex replaced before
12 and older. Yes.
@@VCCBoardRepairs ihave iphone 13 pro max no imei on *#06# but it was showing no sim when you turn on/off flight mode so i swapped lover board but problem still same when i used 3utools and looked for baseband version build and all needed for perfect baseband everything is fine so i updated phone before and after swapping lower board but problem is still same do you have any other suggestion for repair it ?
brow this information is a little wrong, to unlock unbide you no longer need to remove the nand, it is also possible to do the same procedure using i2c, both methods without removing the nand
How do you unbind with JC?
My Netflix channel ❤
Thank you! Appreciate the support!
I’ll do you one better...."This is my pornhub channel😂"
unbound that, data lost bro?
In this case, I restored it
mantap
what
Imagine a world where we can just plug in a new part and it works without jumping through hoops to change a serial number.
That would be the day 🥹
video fo jc v1s pro
Yes. It's coming
Nice job...... but i2c method doesn't need nand tear down and all these stress...... jcid should wake up this is new year
Yes I just heard about the i2C method
Show us please, thanks you
no need to do de solder it
i heard that is true for i2C but not sure about JC method
really people, who buys an apple that has been bitten into!!! the makers of the telephone destroy your expensive device through updates and you remain so calm because of that.. wow 😂😂😂😂😂
u r so right bro the phone performance is just goood
Sent you a message for a repair quote on an iphone 12 PRO, never replied.
Under what name? Are you in the USA? Thank you!