This is lit. I made a similar setup with arduino but using a microservo sg90 and is not as strong as how i want it to push my lock mechanism and this idea and where i want to place the lock would definitely make it work and will be firm to lock the area. Thanx so much for sharing such a great idea, very helpful😊
So, we still need 2 powers right? 5v to arduino and 12v for the solenoid. How if i want to make it just 1 power supply? Did i need IC LM 7805 module or what?
I’m always attracted by those genius projects. And absolutely I’m a real sucker for Arduino and IOT, so could you please tell me the courses or sources to learn this ? I appreciate that ❤️🙏
I made this by using Arduino Nano. When I didn’t connect the solenoid lock, the circuit and relay worked fine. But when I connected the solenoid lock and battery (7.4 V), the circuit stopped working when the solenoid unlocked (LED turned green). However, the circuit still worked fine if the unregistered card was tapped.
On this line: if (content.substring(1) == "83 23 38 BB") Change it to: if(content.substring(1) == "XX XX XX XX" or content.substring(1) == "XX XX XX XX" or ...) add as many as you need for all the keyfobs you want -Ayham Alnasser
In the Serial monitor im not getting anything after putting the card to the sensor it only shows the display message and thats it. What could be the problem?
What if someone stole the right card and access the door. Can u please answer how to overcome that limitation . And Also suggest how to enhance the security for rfid cards
Thanks for the video I got question. How to implement in real situation, in order for us to come out from the room. Do you mind to share maybe some trick or reset button.. This method seems good for entering the room, but I am stuck when how the mechanism when we want to go out. Should we install both rfid sensor inside and outside the room? Tq sir
That can part needs to be explained a bit. Please may you explain what cards need to be used, should the card have a number in order for it to be scanned..
Hello, I wanted to know if you can open a solenoid or two with the same card from the same reader, depending on what you want to do is to use this in a car so when you need to open the passenger door, open both doors Thanks
I have a problem, if I restart the ardiuno the solenoid lock run one or two time after that it does not work, if I disconnect power of solenoid lock, the ardiuno board works very nice, kindly tell me the solution...
hi, why my card ( authorized access ) can loop only one time? after i touch back the rfid, the green led didn't want to light up and solonoid didn't work. it can one time only.
Sir ji mujhe aapki ek help cahiya Maine Arduino rfid door lock banaya h. usme mujhe rfid card ek months access dena h matlab us ek month ki access khatam hone ke baad rfid card se door na open ho. Aap mujhe bata sakte ho uske programming kaise karni hogy plz help. I am waiting your reply. Plz Thank you
Sir, can you make a video on maze solver robot and also a line follower robot which should not stop when the sensors on black line and a white background.
Hi It is great job, but could you please help me to update the code because my lock has two ways, one for opening and another for closing because there is not sprning to plug in. I tryed to do that
hello, I see you haven't gotten a response. On this line: if (content.substring(1) == "83 23 38 BB") Change it to: if(content.substring(1) == "XX XX XX XX" or content.substring(1) == "XX XX XX XX" or ...) add as many as you need for all the keyfobs you want
Amazing! I tried this for my school project and it worked. It helped a lot. Thank you so much :D
Hello, can I use 16v solenoid lock for this project?
Thanks a lot. This video helped me a lot. I was struggling for almost 4 hours & found the solution in this video.
Thanks for posting! My son and I are building this project now :)
How did it go
You're the best love from Bangladesh
This is lit. I made a similar setup with arduino but using a microservo sg90 and is not as strong as how i want it to push my lock mechanism and this idea and where i want to place the lock would definitely make it work and will be firm to lock the area. Thanx so much for sharing such a great idea, very helpful😊
which software are you using for showing connections to us ??
your video will be very helpful to me .
thanks
Do we always need to connect arduino to power even if we have connected solenoid to power
Its possible to allow more than one rfid?
is it possible to alter the time delay on the lock?
Can I do the same thing with a Rasperry Pi???
So, we still need 2 powers right? 5v to arduino and 12v for the solenoid. How if i want to make it just 1 power supply? Did i need IC LM 7805 module or what?
Hi could you please tell me why when i run the code it says MFRC522 is not found i have used all the same parts as in the video
yeah me too
did you download the MFRC552 library? did you install it properly? did you connect the reader properly?
Angelus Reprobi I’ll try downloading the MFRC522 library thank you
@@PureVenomthe1 i dnowalded
a long time ago
I’m always attracted by those genius projects. And absolutely I’m a real sucker for Arduino and IOT, so could you please tell me the courses or sources to learn this ? I appreciate that ❤️🙏
I made this by using Arduino Nano. When I didn’t connect the solenoid lock, the circuit and relay worked fine. But when I connected the solenoid lock and battery (7.4 V), the circuit stopped working when the solenoid unlocked (LED turned green). However, the circuit still worked fine if the unregistered card was tapped.
does the battery power the arduino or does it have to be plugged in
0:51 what programm?
Does it work with Arduino Nano too, or only with the bigger Uno version?
I am looking for information on how to validate several Rfid Tag (mounting arduino uno card + rC522) thank you
On this line: if (content.substring(1) == "83 23 38 BB")
Change it to: if(content.substring(1) == "XX XX XX XX" or content.substring(1) == "XX XX XX XX" or ...)
add as many as you need for all the keyfobs you want
-Ayham Alnasser
how many card can read by this reader and how can we regestor um
It has only 1 card which comes with the rfid sensor
?
In the Serial monitor im not getting anything after putting the card to the sensor it only shows the display message and thats it. What could be the problem?
Would you be locked outside if it ran out of battery?
Great job viral sir 😎😎
What wire did you used?..on the breadboard that is color red
Great project.. next rfid + relay + mysql php
What platform or apps used to run the simulation of the circuit?
could you please tell me which type of software you are using for making virtual circuit
Why do we need the relay, and how can we do and if the reset button is pressed, will the door still open
Does any code is printed on that car or can keep any card
Great video, the circuit and code document on google drive is offline. Could you please upload it again?
Which software use in make circuit diagram in this video?
Fritzing software
I did it, it was fantastic but I need to reset all the system each time I put the card. What should I do?
What if someone stole the right card and access the door. Can u please answer how to overcome that limitation . And Also suggest how to enhance the security for rfid cards
Thanks for the video I got question. How to implement in real situation, in order for us to come out from the room. Do you mind to share maybe some trick or reset button.. This method seems good for entering the room, but I am stuck when how the mechanism when we want to go out. Should we install both rfid sensor inside and outside the room? Tq sir
There is a reset button in the arudino uno. If u press that the door will open
Quel est le logiciel pour tracer le schéma
Bai rfid not read the card during serial monitor Kya problem ho skti h jrur btana
That can part needs to be explained a bit. Please may you explain what cards need to be used, should the card have a number in order for it to be scanned..
What is the schematic software your using in the video
hi, can the solenoid be powered without battery power supply?
Hello, I wanted to know if you can open a solenoid or two with the same card from the same reader, depending on what you want to do is to use this in a car so when you need to open the passenger door, open both doors
Thanks
just connect both selenoid lock to the relay
Como adiciono mais um tag esrou tentando inserir mais um codigo tag e nao consigo o q muda no programa
Is there any solution if badge doest work. How to open manually? Is there ant lock solonoid with key?
Its should be use 2 power?
which battery are u using??
🥺🥺🥺please help me out
Nice Job, How if i want to add another card, in which line i can add the new card code?
Which software you are using for circuit design???
Please tell me
Fritzing software
is it posible to ad different RFID codes?
Hey I have a question. Isn't every RFID tag different so how would we put the right code/signals to the arduino
download the library and run the code, on the monitor page itll tell you the card id
Y didi the RFID module do not taking the RFID card number at serial monitor can you explain the reason
Solenoid Lock and Relay Module works with 12v?? or 5v?
Sir what volts of the battery are you using?
Which camera do you use plz brother tell me
Because i will buy that
can i know what software do you use to sketch the
what software that you use to draw the schematics and can it be like proteus and we can input the coding in the draw
Gran vídeo, gracias por compartir el conocimiento.
Where to connect a button to open the other side of the door without a card ?
Hello. Can you explain how the cards are added?
What kind of battery you used
Please answer ASAP....what battery did u use? And what battery case?...im doing this for my research project
BATTLEGROUND GAMER 18650battery and for case just find 18650 battery case on any shopping web
@@gorden1231996 how can i open the door? If i am inside of it?
hello I would like to know how we should program so that when I type a card, so that its indicates it is that of my mother or my father
Bro, pls make rfid + keypad selenoid door lock video
how do u add the resistor to the bread board?
Which simulation software are you using?
Whats that red wire on the breadboard?
I have a problem, if I restart the ardiuno the solenoid lock run one or two time after that it does not work, if I disconnect power of solenoid lock, the ardiuno board works very nice, kindly tell me the solution...
I have the same problem. Have you figured out why this happens?
hi, why my card ( authorized access ) can loop only one time? after i touch back the rfid, the green led didn't want to light up and solonoid didn't work. it can one time only.
did you figure out the issue? mine just currently started to do that.
@@justinvasquez968 me too ! did you dound the solution ?
can i add a second rfid module?
is it possible to add an lcd to this project?
which is that software used to design the circuit tell me plz
Which software you use?
Thanks for a great video! I have a question: what software did you use to create a diagram?
Schematic
its called 'fritzing' software
Sir ji mujhe aapki ek help cahiya
Maine Arduino rfid door lock banaya h.
usme mujhe rfid card ek months access dena h matlab us ek month ki access khatam hone ke baad rfid card se door na open ho.
Aap mujhe bata sakte ho uske programming kaise karni hogy plz help.
I am waiting your reply.
Plz
Thank you
I am new at this filed, may i know what software you are using and which programming languge you use!
Mohamad Simo it’s the arduino app, u can download it through their website. And for the language you can either use C or C++
@@arthurkayabalian8949 oh thanks a looot 🌷🌷
why i test the component it do not show output at beadboard.......the coding can run
When i connect solenoid lock it works for 1 time. After that i have to reboot it then it works again for 1 time. How to solve this issue ?
#include
#include
#define SS_PIN 10
#define RST_PIN 9
#define LED_G 5 //define green LED pin
#define LED_R 4 //define red LED
#define RELAY 3 //relay pin
#define BUZZER 2 //buzzer pin
#define ACCESS_DELAY 3000
#define DENIED_DELAY 1000
MFRC522 mfrc522(SS_PIN, RST_PIN); // Create MFRC522 instance.
void setup()
{
Serial.begin(9600); // Initiate a serial communication
SPI.begin(); // Initiate SPI bus
mfrc522.PCD_Init(); // Initiate MFRC522
pinMode(LED_G, OUTPUT);
pinMode(LED_R, OUTPUT);
pinMode(RELAY, OUTPUT);
pinMode(BUZZER, OUTPUT);
noTone(BUZZER);
digitalWrite(RELAY, LOW);
Serial.println("Put your card to the reader...");
Serial.println();
}
void loop()
{
// Look for new cards
if ( ! mfrc522.PICC_IsNewCardPresent())
{
return;
}
// Select one of the cards
if ( ! mfrc522.PICC_ReadCardSerial())
{
return;
}
//Show UID on serial monitor
Serial.print("UID tag :");
String content= "";
byte letter;
for (byte i = 0; i < mfrc522.uid.size; i++)
{
Serial.print(mfrc522.uid.uidByte[i] < 0x10 ? " 0" : " ");
Serial.print(mfrc522.uid.uidByte[i], HEX);
content.concat(String(mfrc522.uid.uidByte[i] < 0x10 ? " 0" : " "));
content.concat(String(mfrc522.uid.uidByte[i], HEX));
}
Serial.println();
Serial.print("Message : ");
content.toUpperCase();
if (content.substring(1) == "the UID card or tag goes here") //change here the UID of the card/cards that you want to give access
{
Serial.println("Authorized access");
Serial.println();
digitalWrite(RELAY, HIGH);
delay(ACCESS_DELAY);
digitalWrite(RELAY, LOW);
}
else {
Serial.println(" Access denied");
delay(DENIED_DELAY);
return;
}
}
this should work
is this have a button to open inside?
Hi brother can I use this permanently or its just a prototype. Please reply fast
Really nice job for students room. The sir.
How to add keypad to this circuit?
not sure but cant get LED or buzzer to work
Sir, can you make a video on maze solver robot and also a line follower robot which should not stop when the sensors on black line and a white background.
What battery do u use??
5:24 is the battery required? what is this even for? you just connected the lock with the relay....
the solenoid doorlock requires 12Vdc.
excuse me , one trouble in put th card, how solution
Please if i want to put two or more RFID how can i do l?especially with code
my rfid sensor was working but not the buzzer... the circuit correctly follow the design but still not working... please help me
Worjs with nfc phones?
Link code not found, please repair
www.viralsciencecreativity.com/tutorials/arduino-rfid-solenoid-lock
go check here i got it
@@sharanplays5582 thanks for the help
First tap the card, servo will rotating 180° and the second tapping,servo will return to starting position.
Can i change the coding like above?
Thanks
How would you use servo with solenoid lock?...May be you should go for latch.
how add more cards in program?please help
You might wanna add a diode to the solenoid coil
Hi
It is great job, but could you please help me to update the code because my lock has two ways, one for opening and another for closing because there is not sprning to plug in. I tryed to do that
Hi good day what software/website did u use to draw the circuit diagram
i think it's Fritzing!
i hope you can make a video bout coin operated wifi vendo using arduino...thank you sir...
what simulator used?
Hi i made this whole project but whenever i tap the card the door is getting locked. It is doing opposite
Hello my friend! please tell me, is it possible to install more than 4 cards with different codes? If possible, how can you tell me?
Can i make exit button in rfid arduino
What kind of software is this?
Hi sir gesture switch per ek video banaye
how can i add another tag to be two users?
how to make it non clonable?
Hi
Thank you for your work it is emazing
Please if i want to put two or more RFID how can i do l?especially with code
hello, I see you haven't gotten a response.
On this line: if (content.substring(1) == "83 23 38 BB")
Change it to: if(content.substring(1) == "XX XX XX XX" or content.substring(1) == "XX XX XX XX" or ...)
add as many as you need for all the keyfobs you want
@@AyhamAlnasser how many RFID tags can add?