Get the Best Price at Indiamart: Electronic Modules: dir.indiamart.com/impcat/electronic-modules.html?YTI& Power Modules: dir.indiamart.com/impcat/power-modules.html?YTI& Relay Modules: dir.indiamart.com/impcat/relay-modules.html?YTI&
Hello! Great vid! Curious what’s the minimum mAh lipo battery these boosters are able to still power a 5v sensor. I tried with a 120mAh and my sensor fades after a while. Thanks for your help!
Sir ji, Idea is good.. but be practical.. when light is glowing the smd strip is going to maximum heat and also glue gun's epoxy will be melt. If any doubt do it and then told me.
What kind of hot glue is that? I tried to make a charging circuit with this TP 4056 board (with the battery protection) and hot glue, and the glue only lasted about 30 seconds before it re-melted. The circuit does not get that hot, but warm enough.
Sir I use 18650 battery 4no., With one Tp4056 module and connect with solar panel but relay was not operate. My relay spec. Is 50/60hz jqc-3fc(773)DC06v. Please send a specification of Relay.
using 2 solar panels, one 6v for charger one 5v for the 5v relays . I did not want the relay to take away power from the solar panel for the charger and slow down the battery charge time. so I gave the relay its own panel power source.
O idee buna , dar aplicata gresit. Se leaga sarcina la TP 4056 la bornele ,,out" A good idea, but applied incorrectly. The load is connected to TP 4056 at the "out" terminals
In first project you have connected battery wires and LED wires together. But in fan you have soldered battery and fan on diff terminals. Are you using battery protection in second project ?
My to 4056charging modules red led never sunt off after I charged 3hours, 🙏plz tal me why it's countnusely charge and never stop with 2000mah lithium battery??
Как говорила у меня в школе учительница "за идею 5, а за реализацию 2!" Можно было немного постараться и реализовать все получше и по красивее! Но все же like за старания! ;-)
@@IndianJugaadHacks As spoke my school teacher "for the idea of 5, and for the implementation of the 2!"It was possible to try a little and realize everything better and more beautiful! But still like for the effort! ;-)
according to the schematics at 7:52 only when the solar panel is active it will actuate the relay coil and the LED's will glow with the help of the battery, is should be the opposite: when darkness comes the LED's shines 😃
The relays have 5 connectors, 2 coil, 1 COM, 1 NO-when is the relay coil connected, the NO is connected to COM and 1 NC-when is the relay coil disconnected the NC is connected to COM. He connected the led module to NC ( normal closed )
The 12v relay cut the voltage from the source to the led when sun energize the panel because the output of the pan el solder directly to the relay coil
Hey man, get your hands on a shitload of double sided tape, so that way you can eventually and inevitably pull everything apart to make something new one day ;)
Las conexiones están mal hechas, se conecta todo directamente a bateria, deberia ser al módulo en los pines de out, es ahí donde está la protección El último montaje induce a error, en todos los relés de 5 pines que conozco, los dos pines son la bobina y los otros tres los de utilización.
Get the Best Price at Indiamart:
Electronic Modules: dir.indiamart.com/impcat/electronic-modules.html?YTI&
Power Modules: dir.indiamart.com/impcat/power-modules.html?YTI&
Relay Modules: dir.indiamart.com/impcat/relay-modules.html?YTI&
Hello! Great vid! Curious what’s the minimum mAh lipo battery these boosters are able to still power a 5v sensor. I tried with a 120mAh and my sensor fades after a while. Thanks for your help!
Can i use fidget spinner plastic box ?? and mein cold drink bottle use kar sakta hun tread cone ki jgha? Reply me
Sir ji, Idea is good.. but be practical.. when light is glowing the smd strip is going to maximum heat and also glue gun's epoxy will be melt. If any doubt do it and then told me.
What is RELAY for ? What is the fuction of it ?
Can I charge through micro USB with phone charger in this project ?
Why protection not used in tp4056 board.. You should solder out +/- instead of both wires to bat+/-
Totally correct! I was about to say the same thing.
But it occurs to me now that the Samsung battery that was used already has built-in protection.
I want to ask the same question too. If protection is not used,can buy another version with charging function only. Cheaper in price.
मोबाइल की बैटरी में शॉर्ट सर्किट प्रोटेक्शन होता है
Can it leave it connected to the power suplyy?
You are going to start a fire! That board offers slight protection through the outside pins, but you just soldered straight to the battery!!!!!
Does it really charge the battery i have bought one but it does not shows blue it always in red light
Bhai lead acid(Li ion nehi) battery 4v charge karne ke liye mobile charger 5v use kar sakte hai ?
how many Watts of solar panels do you use?
, Please respons
It is possible that this circuit will provide 4A current by marely changing resistor.. if not any 2A/ 3A output hack
You can use TP 5100 charging module.
This video makes me reconsider the definition of amazing.
can I use this board as a bms,?
For drill machine battery lithium
3.7volts 2500mah *2nos.
Can you charge LiFePO4, battery with this tp4056 board
Does this really work with 4v lead acid battery you used in the 3rd part?
Last video is 👏🏻👏🏻👏🏻👏🏻👏🏻
Great!
Thanks
my lead acid battery not working in this tp4056 module. what way to work
Very Good...!!!
What kind of hot glue is that? I tried to make a charging circuit with this TP 4056 board (with the battery protection) and hot glue, and the glue only lasted about 30 seconds before it re-melted. The circuit does not get that hot, but warm enough.
For the last one can I use a 5v relay please reply
Sar ye modul se tirimmer Ka 3v Ka battery chargerj Kar Sakta hai
Toooo goood 👍👍👍👍🤔
Thanks
Hello, very very good lantern.
Pls., help me : were can i purchase the 4VDC LEDS strip.
Thank you in advance,
Sergio
Link given in video description.
In your description Is not the same item. I tried to find this you used but i didn't find. Can you help please, TNXS!!
Pls., give the type of the 4V led used in your LightFlash - TNXS
Please find 4v smd led strip in online shopping websites.
You can also get from flipkart
Whenever i use a Li-ion battery do i have to use the TP 4056 or can i use directly the USB cable connected to the battery?
Yes! If you use Li-ion battery you have to connect TP 4056 MODULE .
Sir I use 18650 battery 4no., With one Tp4056 module and connect with solar panel but relay was not operate. My relay spec. Is 50/60hz jqc-3fc(773)DC06v. Please send a specification of Relay.
Sir make a same video with ldr this working only High sunlight I made same after watching your video
Sir dose your module heat while charging.????
No
But when I connect my battery to module, while charging it heat very hot
Hassan Khan then theys too much voltage to it..
using 2 solar panels, one 6v for charger one 5v for the 5v relays . I did not want the relay to take away power from the solar panel for the charger and slow down the battery charge time. so I gave the relay its own panel power source.
Instead of charging it with charger can we connect it with 3w 6v solar panel and is there any extra item to be connected
Tp4056 can handle up to 8v. Charging via 6v mini solar panel is ok.
One batrey.. How Batrey 2S 7.4V..? Make modul like what?.. Thx brother
Superb vedio Bhai sabkuchh samaj me aa jata hai.solar kit kaha se milegi please answer.
Amazon se.
Link video ke description me diya hai.
@@IndianJugaadHacks Thanks for reply Bhai 👍mene aap ka chenal subscribe kar diya he.
👍
Si I have done bt tez dhoop m hi kaam kr raha hai relay thodi si kam dhoop hoti hai to led onn ho jati hai give solution
Where i will get battey charger kit , i used to live in Mumbai
Link in description
beautiful lamp
Thnx
Can it charge 3.7v lipo batteries
Yes
Good video using some things
Thanks
O idee buna , dar aplicata gresit. Se leaga sarcina la TP 4056 la bornele ,,out"
A good idea, but applied incorrectly. The load is connected to TP 4056 at the "out" terminals
love you brother, thank you for the video!!!!
Welcome
Two battery outputs are there in the board pls tell for what purpose
Not two output for battery one output for battery and one output for device
In first project you have connected battery wires and LED wires together. But in fan you have soldered battery and fan on diff terminals. Are you using battery protection in second project ?
Bhut badhiya video Bhai tere video se ek problem solving ho gya
Thnks
hi, should the load be disconnected when the battery is being charged?
No need, you can draw current from the output when it is charging
Bro 3.7 volt ki mobile battery charge hogi
Yes
All mobile battery charge hogi pakka
Power bank ki 4 batri laga sakte he kya is bord me
Laga sakte hai.
My to 4056charging modules red led never sunt off after I charged 3hours, 🙏plz tal me why it's countnusely charge and never stop with 2000mah lithium battery??
Bro I charge my self made neckband 2200 mah battery ... It charges within 20-40 mins...
Blue LED also turn on....
Can I use negative terimal wire in switch?
Yes
what is the out put voltage
Nice project 👌
Thanks
If we don’t want to connect it with led strips and want to connect it with 1w bulbs or less then 1 w ?
Mitesh Dhanani uni
There must be a huge market in India for diy CRAP!! :-))
Sir answer dejiye kam dhoop m led off nai hoti
Bhi aap power bank ka sarkit bord kaha se parches korte ho
Amazon
Does it charge 18650 li ion battery
Yes! It can charge 18650 li ion battery.
@@IndianJugaadHacks kya do battery ek sath parallel jodkar only one TP4056 SE CHARGE kar sakte hai
@@luckyrathod5345 yes why not but it will take more time to charge
Как говорила у меня в школе учительница "за идею 5, а за реализацию 2!" Можно было немного постараться и реализовать все получше и по красивее! Но все же like за старания! ;-)
Thnx
Plz write in English.
@@IndianJugaadHacks As spoke my school teacher "for the idea of 5, and for the implementation of the 2!"It was possible to try a little and realize everything better and more beautiful! But still like for the effort! ;-)
Thnx
All mobile battery charge hogi
Yes
Good...
Thanks
Hello very nice video but the smd led module link is not the same as the ones in your video.
Thnks
Vraiment top. :-) Jolie vidéo.
Thnks.
Thnks
At which online shopping app you buy all this materials Plz send back comment Plz Plz Plz. ?..
Do not turn on the device connected to tp4056 when your charging it. It's on the datasheet. If you want to burn your house have fun!
Thnks for information
Bro pls explain me how to connect lead acid battery with mobile charger to double pole three way switch
Can the battery run on the device if the batgery is being charging
No It Will Kill The Phone Immediately Because There’s 220volts going inside the mobile battery slot
Good ideas 👍
Thnks.
rly??? for load on this module have other place like "out +/-". In other way u will kill your battery
Thnks for comment
That guy is stupid. He's putting stupid video for views.
How much time it take to charge 4000 mah battery
It would show that it is charged because this module is designed for charging 18650 li - ion battery only which ranges to 1500-2500 mah
according to the schematics at 7:52 only when the solar panel is active it will actuate the relay coil and the LED's will glow with the help of the battery, is should be the opposite: when darkness comes the LED's shines 😃
👍
Right bro...😂😂
The relays have 5 connectors, 2 coil, 1 COM, 1 NO-when is the relay coil connected, the NO is connected to COM and 1 NC-when is the relay coil disconnected the NC is connected to COM. He connected the led module to NC ( normal closed )
In last project what does the 12v relay do?
What does it do? I'm unsue3
Unsure
The 12v relay cut the voltage from the source to the led when sun energize the panel because the output of the pan el solder directly to the relay coil
Ye board konsi market m milega
Link in description
I make power bank the battery will charge and i use old charger to connect battery the mobile will not charge plz reply bro plz plz
Bro mobile charger needs 220v AC
Supply .
What I want to do
You have to use power bank module.
Kha sa mille ga cip j kon c ha name Kya ha
Good job
Thnks
Sir isse 1 0000 mah ki battery ko char g kar sakte hai ?
Ha lakin bht dayr lay ga
Bro aap kitne watt ka solidring iron use krte ho
25watt
25 Watts ka soldering iron
You earned my sub good job bro
Thanx
Man, you’re overriding the protection circuit against overdischarge. Not a good idea.
Thnks for comment
this module good work with 6v solar panel
Thnx for comment.
Bro when battery charge and output is released at same time how to fix it plz
It's charger output not a problem
bravissimo. complimenti!
Thnx.
bhai ye kit ke bina nhi bnega solar lite kya
Nahi
good idea
Thnx.
can I use 5v relay
Yes
Почему подключил аккумулятор без контроля разряда?
This charging module must use heat sink to reduce the heat from IC TP 4056, or change the R3 to 1.8K OHM, to make charging current to be 700mA.
it charges completely fine without one
Nice and clean looking lamp! Im impressed!
Thanks
Relay 5 volt kabuse kiya maine
I will connect for your structure correctly but the battery cannot charge and the blue light is flash
Plz check battery.
I use samsung battery its condition is Good
Oh! Then you have to check output
Voltage by multi meter.
What's voltage battery op or module op
And how much of its voltage have
Nice
Thnx
this is like a 70s movie, the dialogue is like 50% volume while music is blasted at 250%
Hay you mess the over discharge featur
TP4056 is battery charge with protection
nice
Thanks for your valuable comment
Charging module kha par milta hai
Amazon link given in description.
bhai 6v relay amazon pe mil jye g
Yes
ruclips.net/user/my_videos?ar=2&o=U&pi=1
Link not open.
ruclips.net/video/3JDDXAAN5XM/видео.html
It is not recommended to use hot glue on battery, charging module and leds.... Charging module and leds are turning hot and melt the glue
relay not work is panel ampire low and low voltage ..relay power cumsuption so bad charging
How can we connect it with 3w 6v solar panel
Thnks for your precious comment
And watch videos with concentrate to trace the connection.
Where is the over discharge protection
TP4056 is battery charge with protection
bhai ye kitna ampire ka relay hai
Hey man, get your hands on a shitload of double sided tape, so that way you can eventually and inevitably pull everything apart to make something new one day ;)
Las conexiones están mal hechas, se conecta todo directamente a bateria, deberia ser al módulo en los pines de out, es ahí donde está la protección
El último montaje induce a error, en todos los relés de 5 pines que conozco, los dos pines son la bobina y los otros tres los de utilización.