Today, we take the PowerEdge R620 that I picked up from @ServerMonkey and configure the iDRAC port. I typically setup the iDRAC port to update the BIOS, firmware and push out the operating system when I don't want to be inside the cold LAN room setting up the server. Once I'm done with the configuration I kill the connection and remote desktop into the server to continue the configuration. Please enjoy and be safe everyone 🤓
Sub'd because of this vid! I don't need virtual or animated explanations like some around on YT... I need to physically SEE it first, so I can understand what's going on and then I "translate" it in my head into virtual stuff... So THX for this series and therefore the sub! Greetings from Belgium! 😉
@@SVT000 nope, heb het anders gedaan. Trouwens letterlijk net gekocht hehehe. Ga voor NUC (met VMs op) die dan NAS (storage) bediend. Minder verbruik en lawaai ;)
Hey man, Few things to help you out with. Please don't take this as a rant or telling you want to do. 1) iDRACS should always be set on a static IP. ALWAYS! lol (you didn't need to set a DHCP at first) 2) Even if you did DHCP, why not just ping the IP to see if the IP is responding? lol 3) Best practice is to have your physical servers and VMs be on X subnet/vlan then your workstations, wireless, and IoT devices on a separate subnet/vlan (honestly all of those should have their own vlan and subnet to help distinguish what type of device they are by IP). 4) The R620 does work with Chrome. You need to go to the "settings" just above "launch" and change from Java to HTML5. Hit Apply and then you have Chrome support 5) Make sure you add it to the domain.
He could use DHCP reservation to keep the IP the same. However, I set all BMCs with a static IP as well. I use an Excel spreadsheet to manage statically assigned IPs. I like your recommendation of having a separate management network.
@@MichaelStepniewski I agree with your DHCP reservation statement. My choice (as well as yours) to use static is due to if whatever is hosting his DHCP scopes goes down and the iDRAC attempts to reach out to renew IP, it could lose said IP and now be effed. I am a network engineer and help support/manage 30 locations for my company. Since my role is more than just a Network Engineer, we created each said location to have at least 6 vlans/subnets for separating traffic so creating a vlan/subnet scheme was very necessary. Saves a lot of time when tracking down and resolving networking issues.
1) This is correct, but I set up DHCP for the server to get an IP address (temporary). I could of just took a laptop and set it to the same subnet of 192.168.0.x and set it up that way too. Then look at the IP address spreadsheet to see what's available ( yes I have one 😀 ). I did configure a static IP address on it at the end. wait.... did I? 🤔 😂 2) This is correct, but again I try to break down the video into a simple and easy steps. I could have done this video faster, but some people will complain that I'm going to fast and need to slow down. This is me slowing stuff down and breaking things down. lol (also my methods are very stubborn) - I did configure a static IP address at the end - 😂 3) 100% agree with you on this one. VLANs for the win! 4) Crap! didn't know that. I always use Firefox at the 9-5 job and use Chrome when I doing the recordings for you guys. Great tip and I will change my settings. Strange that chrome doesn't have HTML5 enabled by default. 5) adding to the domain I like doing this at a production level. when it's a lab server like this one. I typically add the ESXi server into domain. By the way, I don't see it as a rant. We're all here to learn from each other. No one is perfect. I appreciate the time you took to give me pointers and check out the video. Be safe my friend and thank you. Didn't know you were a Network Engineer. Would love to pick your brain one day.
@@bjtechnewshd I cannot post a screen shot, but I am not talking about enable HTML5 in Chrome, but in the iDRAC. Go back to the Overview Screen on the iDRAC. To the right, where the preview window is, click on settings. In settings you will see "Plug-in type" Change this from Native (or java) and switch it to HTML5. This will allow you to use chrome. Any time you like you are welcome to message me.
@@loganbat1310 When I was looking for it and didn't see it. I said "he might be talking about the iDRAC portal", so I went to Overview > Server > Virtual Console and noticed Plug-in Type set to Java.
I got this same server refurb for like 500. I use it with windows bc of school and have a bunch of different VMs on it. I love having all that power and would love to add sound and maybe even graphics down the road.
Thank you. If you allow me to raise a question, I have R640 and when I power on the server the fans sound is high and the display shows colour bands not the normal texts. It shows no amber LED. Any help please?
You should be able to configure it from the server by using Ctrl E then don’t need to worry about dhcp, what if the idrac was previously configured for static on another machine? Keep in mind I used idrac 6
@BTNHD I don't get any link lights under the ethernet cable port connection to the iDRAC. When I'm in the iDRAC Settings under Network Settings-->NIC Selection: I only see LOM1 to LOM4. Any suggestions on what I need to do?
I've got an old Dell C6100 I what to move out to the garage for domestic harmony reasons, never messed with KVM-IP before, got a few questions about KVM-IP capabilities? Can KVM-IP be used for power off, on, reboot? What's the Video quality and lag time for static and video like? Basically how does it compare to direct connection.
Thank you for the video. Do you need a license to access the IDrac in you own LAN? can con connect a regular ethernet cable? I plug mine but the light on the iDrac port dont turn on.
The r620 has a standard express license. The enterprise license had to be purchased. If there’s a enterprise license that comes with the server then you are in luck.
If you have an Enterprise license and the in DRAC setting if the port is set to dedicated, the dedicated DRAC port will work, but if its on express license you should choose the port as LOM1 (your regular network port becomes shared) , Dedicated network port on works with Enterprise license, you can try googling for a trial Enterprise license, if you havent used on on the server
@@MrTsatia if you put the tag in the support site, it should show under configuration what it was ordered with, however easiest would be to call Dell tech support, because they can verify what license you have and email it to you if you don't have it, even if your out of warranty. In support site after you put your tag, on the right side where there is quick links you can see view product specs, that will show your original order
Hey I have a quick question if any of you can answer I’m a noob my tower won’t connect to any of my USB cables and but will power on is it my mother board and how much would a fix be or how could I find out what’s wrong
You would either need remote access to your network via a VPN or a PC on your local network via a remote access software such as teamviewer, anydesk, etc. You could also make the IP of your iDRAC public facing via your firewall. I would not recommend making the iDRAC public facing for security reasons.
I popped the drives out and booted and got to the life cycle screen, setup dhcp, got my IP, but the default user/pass of root/Calvin doesnt work and the tag on the machine doesnt have a pass on it.
Thanks for the video!! When I go into the network settings I have everything set the same as you..but when I try to update the firmware it still prompts me to configure the network settings. Once I go in there again it is set to DHCP but shows no NIC selected/IP address. When I select any of the NIC options(of the 4) and it is still left blank. Any idea as to what may be the issue?
Duuude! You are awnsome!!! But I need a little extra help. My certificate has been expired. Can you help me to renew the certificate? Model: PowerEdge R610 - iDRAC6
Today, we take the PowerEdge R620 that I picked up from @ServerMonkey and configure the iDRAC port. I typically setup the iDRAC port to update the BIOS, firmware and push out the operating system when I don't want to be inside the cold LAN room setting up the server. Once I'm done with the configuration I kill the connection and remote desktop into the server to continue the configuration. Please enjoy and be safe everyone 🤓
Great just what this newbie was looking for precise and straight talking . Thank you !!!
Sub'd because of this vid! I don't need virtual or animated explanations like some around on YT... I need to physically SEE it first, so I can understand what's going on and then I "translate" it in my head into virtual stuff... So THX for this series and therefore the sub! Greetings from Belgium! 😉
Heb je ook een r620 ?
@@SVT000 nope, heb het anders gedaan. Trouwens letterlijk net gekocht hehehe. Ga voor NUC (met VMs op) die dan NAS (storage) bediend. Minder verbruik en lawaai ;)
Very well done video, for an iDRAC newbie! Thank you!
i do not blame you for stepping out this thing takes its sweet time
Enjoyed it much. Great job BTNHD
So clear and informative video thanks a lot bro
Glad it was helpful!
Hey man,
Few things to help you out with. Please don't take this as a rant or telling you want to do.
1) iDRACS should always be set on a static IP. ALWAYS! lol (you didn't need to set a DHCP at first)
2) Even if you did DHCP, why not just ping the IP to see if the IP is responding? lol
3) Best practice is to have your physical servers and VMs be on X subnet/vlan then your workstations, wireless, and IoT devices on a separate subnet/vlan (honestly all of those should have their own vlan and subnet to help distinguish what type of device they are by IP).
4) The R620 does work with Chrome. You need to go to the "settings" just above "launch" and change from Java to HTML5. Hit Apply and then you have Chrome support
5) Make sure you add it to the domain.
He could use DHCP reservation to keep the IP the same. However, I set all BMCs with a static IP as well. I use an Excel spreadsheet to manage statically assigned IPs. I like your recommendation of having a separate management network.
@@MichaelStepniewski I agree with your DHCP reservation statement. My choice (as well as yours) to use static is due to if whatever is hosting his DHCP scopes goes down and the iDRAC attempts to reach out to renew IP, it could lose said IP and now be effed.
I am a network engineer and help support/manage 30 locations for my company. Since my role is more than just a Network Engineer, we created each said location to have at least 6 vlans/subnets for separating traffic so creating a vlan/subnet scheme was very necessary. Saves a lot of time when tracking down and resolving networking issues.
1) This is correct, but I set up DHCP for the server to get an IP address (temporary). I could of just took a laptop and set it to the same subnet of 192.168.0.x and set it up that way too. Then look at the IP address spreadsheet to see what's available ( yes I have one 😀 ). I did configure a static IP address on it at the end. wait.... did I? 🤔 😂
2) This is correct, but again I try to break down the video into a simple and easy steps. I could have done this video faster, but some people will complain that I'm going to fast and need to slow down. This is me slowing stuff down and breaking things down. lol (also my methods are very stubborn) - I did configure a static IP address at the end - 😂
3) 100% agree with you on this one. VLANs for the win!
4) Crap! didn't know that. I always use Firefox at the 9-5 job and use Chrome when I doing the recordings for you guys. Great tip and I will change my settings. Strange that chrome doesn't have HTML5 enabled by default.
5) adding to the domain I like doing this at a production level. when it's a lab server like this one. I typically add the ESXi server into domain.
By the way, I don't see it as a rant. We're all here to learn from each other. No one is perfect. I appreciate the time you took to give me pointers and check out the video. Be safe my friend and thank you. Didn't know you were a Network Engineer. Would love to pick your brain one day.
@@bjtechnewshd I cannot post a screen shot, but I am not talking about enable HTML5 in Chrome, but in the iDRAC. Go back to the Overview Screen on the iDRAC. To the right, where the preview window is, click on settings. In settings you will see "Plug-in type" Change this from Native (or java) and switch it to HTML5. This will allow you to use chrome.
Any time you like you are welcome to message me.
@@loganbat1310 When I was looking for it and didn't see it. I said "he might be talking about the iDRAC portal", so I went to Overview > Server > Virtual Console and noticed Plug-in Type set to Java.
Great vid we appreciate the attention to detail
Doing this with an R630 I got cheap. Thanks for the guide!
I got this same server refurb for like 500. I use it with windows bc of school and have a bunch of different VMs on it. I love having all that power and would love to add sound and maybe even graphics down the road.
Thank you. If you allow me to raise a question, I have R640 and when I power on the server the fans sound is high and the display shows colour bands not the normal texts. It shows no amber LED. Any help please?
You should be able to configure it from the server by using Ctrl E then don’t need to worry about dhcp, what if the idrac was previously configured for static on another machine? Keep in mind I used idrac 6
Hi BTNHD, where did you buy the iDrac license ?
does have to be done at startup? i have to program this on a server without rebooting. thank you.
thanks so much for this video bro ! God Blass you !
i got to 1:16 mine wont display anything
Very useful. Thank you.
I'm glad you found it helpful!
Great Job!
@BTNHD I don't get any link lights under the ethernet cable port connection to the iDRAC. When I'm in the iDRAC Settings under Network Settings-->NIC Selection: I only see LOM1 to LOM4. Any suggestions on what I need to do?
I've got an old Dell C6100 I what to move out to the garage for domestic harmony reasons, never messed with KVM-IP before, got a few questions about KVM-IP capabilities?
Can KVM-IP be used for power off, on, reboot?
What's the Video quality and lag time for static and video like?
Basically how does it compare to direct connection.
Great video
Thanks!
i got one as a donation from a company, but it has a setup password, do you know the defaults or any way to reset it?
Great job! Thank you!
hey is it possible to use a laptop in place of my keyboard and monitor?
What should I do if when I try and boot up the server it will configure the memory successfully but fail to initialize IDRAC?
Perfect!
Thanks
how did you get in the life cycle controller
Thank you for the video. Do you need a license to access the IDrac in you own LAN? can con connect a regular ethernet cable? I plug mine but the light on the iDrac port dont turn on.
The r620 has a standard express license. The enterprise license had to be purchased. If there’s a enterprise license that comes with the server then you are in luck.
If you have an Enterprise license and the in DRAC setting if the port is set to dedicated, the dedicated DRAC port will work, but if its on express license you should choose the port as LOM1 (your regular network port becomes shared) , Dedicated network port on works with Enterprise license, you can try googling for a trial Enterprise license, if you havent used on on the server
@@eddscall how to verify which license we have?
@@MrTsatia if you put the tag in the support site, it should show under configuration what it was ordered with, however easiest would be to call Dell tech support, because they can verify what license you have and email it to you if you don't have it, even if your out of warranty.
In support site after you put your tag, on the right side where there is quick links you can see view product specs, that will show your original order
Really helpful expect more.. like same
Hi , I need help how do I do it using my laptop coz I need to extract logs
hello.
Good day sir.. the port for Idrac and port for my Internet are plug to the same modem or switch right?
the virtual console on my R620 is windows server 2016. please do you know why its like that?
We can turn on server remotely?
Hey I have a quick question if any of you can answer I’m a noob my tower won’t connect to any of my USB cables and but will power on is it my mother board and how much would a fix be or how could I find out what’s wrong
Hey,
I have a dell poweredge r320. But everything has sat good.
But if i set the ip in the web adress. It says it takes to long to get response
I have solved it
You are sitting right in front of the server. Why do you want to config iDRAC?
Convenience having a tablet or a laptop over a keyboard mouse and monitor and cart
Are you going to do a video on the firmware updates and all the software updates
Thanks Mate!
how to change the iDRAC name in iDRAC9 enterprise?
I have a Dell R720. Is it possible to connect to iDRAC 7 remotely away from home?
You would either need remote access to your network via a VPN or a PC on your local network via a remote access software such as teamviewer, anydesk, etc. You could also make the IP of your iDRAC public facing via your firewall. I would not recommend making the iDRAC public facing for security reasons.
Tanks , very good
iDRAC works in firefox for the r620
I bought one of these second hand, I dont see this idrac stuff, it boots to a vmware page and asks me to log in, ofc I dont have the details.
I popped the drives out and booted and got to the life cycle screen, setup dhcp, got my IP, but the default user/pass of root/Calvin doesnt work and the tag on the machine doesnt have a pass on it.
Thank you!!!
Thank you so much
I cannot log into my r620 idrac7 - says login failed - how do i reset the password to default
will sub thank you so much -- I am setting up a 2 R630 --
BTNHD: " We have to use Internet Explorer "
Cj: "Ah Sh!t, Here We Go Again"
“Just when I thought I was out, they bring me back in” -Scarface when he had to use IE on his R710 config
muito obrigado!! me salvou !
Nice 👍
I use a Mac and Firefox works. And to avoid all the java stuff, I set Console > Plugin Type to HTML5
How to install mikrotik on Dell server plss help me sr
Hay Sir, where is the serial number?
Excelente, Agradecido
When I was setting up the iDRAC, I accidently set the system password in the bios. The question is, can I clear the password?
Clear the bios… old fashioned way by removing the battery on a regular pc, not sure about servers with preos
Thanks for the video!!
When I go into the network settings I have everything set the same as you..but when I try to update the firmware it still prompts me to configure the network settings. Once I go in there again it is set to DHCP but shows no NIC selected/IP address. When I select any of the NIC options(of the 4) and it is still left blank.
Any idea as to what may be the issue?
Not working it keeps saying secure connection failed please help
Tow 1.2 is the minimum supported in Firefox
Thanks this is what I need to know, I have a R710 any Different. (installing proxmox) I will order a R620 and a R720 later, thanks again
R710 will have DRAC6 and its not as good as DRAC7 and 8
Has anyone had trouble opening the virtual console. I tried it with Firefox and chrome. No luck.
Note: it doesn’t open in internet explorer for me. Either
I think it also should work with firefox
Duuude! You are awnsome!!! But I need a little extra help. My certificate has been expired. Can you help me to renew the certificate? Model: PowerEdge R610 - iDRAC6
thanks
Way too many errors. Says to check DNS for ip - no it’s DHCP. Next he says his ip address is One One 12, NO it’s 112 not 1112!!!
and there’s more…
"awesome"
"AMEI"ZING
Default username is 'root' and password is 'Calvin'