For the 2011 Corolla, there is an inexpensive workaround. I bought a quality brand 1/4 in torque wrench. It generally "clicks when it's supposed to but I was so paranoid after cracking my first filter housing I arrived at a simple workaround that gives me the desired torque, without overtightening. I also do not require a torque wrench. First ... when removing the housing, as gently as possible, unscrew the housing. Do not yank, grab, jerk or wrestle the housing off. Gently, gently unscrew the cap until finger loose. Remove normally after that. When tightening, gently tighten the cap towards the housing (base) surface. Just before you've tightened it fully, ensure you can insert a 0.15mm feeler gauge between the cap and the base. If you have a snug (not tight) fit. You're good to go. But I repeat, gently, gently tighten the housing down to that gap. More and you risk cracking the housing a few months later when you change your filter. Generally that is when the caps crack. This has worked without issue for two full oil changes without leaking and the housing was easy to twist off without an initial jerk or tug to loosen. It just immediately began to twist out as soon as I put the faintest pressure on it. That's it. Guaranteed "decent" accuracy of torque without overtightening and without a torque wrench. Best of days to all.
Just grabbed a new one from Toyota and the parts manager said it’s only hand tight. Their service guy probably tighten it with a wrench and I had to use a breaker bar just to get it off. Torque lb for 17 Camry is only 7-8 foot pounds.
@@kennynhannguyen8666 I don't understand why Toyota made the housing parts this way. If I had been driving and didn't notice the leak, my engine could have locked up. Now it's time to buy more engine oil and a new housing lol
It happens to me today to I have to use a breaker bar to get loose so I figure tied good enough and I cracked it
Hi Den Khoe khong thay Em tren RUclips con Trang voi Chi Lan the Nao? Can khoe Chua
Dạ cám ơn khỏe bình thường.
For the 2011 Corolla, there is an inexpensive workaround.
I bought a quality brand 1/4 in torque wrench. It generally "clicks when it's supposed to but I was so paranoid after cracking my first filter housing I arrived at a simple workaround that gives me the desired torque, without overtightening. I also do not require a torque wrench.
First ... when removing the housing, as gently as possible, unscrew the housing. Do not yank, grab, jerk or wrestle the housing off. Gently, gently unscrew the cap until finger loose. Remove normally after that.
When tightening, gently tighten the cap towards the housing (base) surface. Just before you've tightened it fully, ensure you can insert a 0.15mm feeler gauge between the cap and the base. If you have a snug (not tight) fit. You're good to go.
But I repeat, gently, gently tighten the housing down to that gap. More and you risk cracking the housing a few months later when you change your filter. Generally that is when the caps crack.
This has worked without issue for two full oil changes without leaking and the housing was easy to twist off without an initial jerk or tug to loosen. It just immediately began to twist out as soon as I put the faintest pressure on it. That's it. Guaranteed "decent" accuracy of torque without overtightening and without a torque wrench.
Best of days to all.
Just happened to me on 17 Camry. Dealership did the oil change last. That was my first oil change on my Camry. Thanks for the tip
It happened a lot
Just grabbed a new one from Toyota and the parts manager said it’s only hand tight. Their service guy probably tighten it with a wrench and I had to use a breaker bar just to get it off. Torque lb for 17 Camry is only 7-8 foot pounds.
@@touahero awesome thank you for your information
This just happened to my Camry. Luckily I only started the car for a few seconds
They made cheaper material. The older version made aluminum housing much better & last longer. Thank you for watching
@@kennynhannguyen8666 I don't understand why Toyota made the housing parts this way. If I had been driving and didn't notice the leak, my engine could have locked up. Now it's time to buy more engine oil and a new housing lol
@@starfox4919 yes. I have bought 2 of them 1 extra for in case that happens again
Mine just cracked How do I get mine off TOYOTA CAMRY SE 4 CYL
Oh no. Just be gentle & use the oil filter cap tool line it it up to break it loose. Or use a big channel lock Player Loose it. Good luck
@@kennynhannguyen8666 I went back out and unscrewed it but it's stuck in the oil fill cap now