You can buy the tail tidy from Amazon link is below👇 MotoPro Compact Tail Tidy/Fender Eliminator for Husqvarna Svartpilen & Vitpilen 250 amzn.eu/d/3kOmtB6
You have to set the gap between the number plate and mudguard about 5 inches nothing will happen. I have ridden the bike for almost 3k kms. It has never touched the mudguard.
Yes it does get on my back. I have used this fender for 2 months and then replaced it with the stock wheel hugger. The stock wheel hugger does a better job at it.
It's an issue if you ride with pillion. The bottom will touch on steep speed breaker. On normal speed breaker it's not an issue. Solo ride its never an issue.
Same I wanted to say. I bought Start only for the original look.. only thing suitable was tail tidy still we can search for good tail tidy in some biker points
If you mount the tail tidy as it's supposed to fit then yes it will hit the wheel because the gap between the wheel and the number plate has to be more than 5 inches. If you fix it like how I have fixed then no it will not hit the wheel hugger. I am using it with ktm wheel hugger at present.
@@greyandwhite9730 Did you try the ns 200 number plate holder. I think it is more longer which will not hit the hugger. Even with the hugger I am getting dirt on my shoulder and Helmet. So planning to keep both hugger and the plate holder
@@shameempk007 I did think of using the number plate holder of the ns. But the mounting points for this holder don't match on the husky. You have to drill holes on the underside of the panels to fit it. I didn't want to do it so I didn't try.
You get it in RE service center just show them the pic or in a parked RE classic front indicator. They will understand. I don't think you will get this online.
Radiator guards don't make sense to me, They don't offer complete cover as there are gaps for air flow so there is a chance of radiator getting damaged even with the guard. They cost 1500 I think it's very close to what a brand new radiator would cost. I would rather buy a brand new radiator instead. And my biggest problem, you still have to clean the whole thing as it keeps accumulating dirt. And if you think the mud flap looks horrible, It cost me just 95rs. It's keeping my radiator super clean, no mud water has spashed on my radiator after installing it. It has kept the radiator safe from debris flying off from the front wheel. In this case I would take horrible looks over radiator guard any day. Spend your money wisely!
@@greyandwhite9730 if you would take horrible looks over spending money, I think then you should also buy cheap bikes over husqvarna, if you want to add 95 rs cheap things on your bike. If you want to own a bmw you can’t have a maruti mentality.
@@ankitchahar7091 if the radiator guard is not providing me with what I need on my bike, why should I use it. If a mud flap is providing me with what I want then I am going to use it. Is this that difficult for you to understand??
It's a bit too tall for 5'4" may be. You can take a test ride and see if it works out. You can ride the bike reducing the preload on the rear suspension that will further reduce the ride height when you sit. As stock the preload on the rear is set to medium.
You can buy the tail tidy from Amazon link is below👇
MotoPro Compact Tail Tidy/Fender Eliminator for Husqvarna Svartpilen & Vitpilen 250 amzn.eu/d/3kOmtB6
Good video, well explained.
such a detailed and technical explanation... Your bike looks amazing with the mods.. Thanks for sharing and ride safe Buddy!
Superb bro I was looking for the exact stuff and I can see you invest a lot of time and efforts here and we are the bike lovers...... Thankyou so much
amazing video! really loved it!
Such a great looking bike
Now it’s looks perfect 🤘🏻🤘🏻🔥🔥
Wow great video brother 🙌 you’ve convinced me to buy one ☝️
Dont shift number plate to down side, it will scrach of your front mud guard. I experienced the same issue previously when i was changed it to down.
You have to set the gap between the number plate and mudguard about 5 inches nothing will happen. I have ridden the bike for almost 3k kms. It has never touched the mudguard.
Even I did fender extension mod with bs3 Duke extension
Can u please sent the link of mod of no. 3 tail teddy and Royal infield product
bhai aapne ye tail number plate stand kahan se lia plz share share link
Best tail tidy in svartpilen ever…
Thanks👍🏽
can u send that royal enfield brakets link or make a small video on it
Nice mods bro. I own Svartpilen as well and looking for good tail tidy. I hope this one would be good. Please review this after 1000km.
I'll try to make follow up videos or give feedback whenever time permits✌
Can u make a video of tail tidy installation plzz
Hi can you share the link for tale tydi
How's the dirt with that rear fender? does it get over your back?
Yes it does get on my back. I have used this fender for 2 months and then replaced it with the stock wheel hugger. The stock wheel hugger does a better job at it.
It's looking sexy yrr ! I have to do it as well ! ❤
Bro what you did with the wire that use to connect the light above the number plate
I removed it from the chain cover and brought it under the seat.
Nice vlog bro.. What about ground clearance issue on this bike
It's an issue if you ride with pillion. The bottom will touch on steep speed breaker. On normal speed breaker it's not an issue.
Solo ride its never an issue.
Any sort of vibrations on the tail tidy?
Yes It vibrates since it's not mounted directly on the chassis.
Hello bro can you send me the link from where you bought that bracket for tail tidy
www.amazon.in/dp/B0982DNY3S/ref=cm_sw_r_apa_i_FCKE3H9KH3GAGY4S520R_1?_encoding=UTF8&psc=1
It's looking like you really don't like your bike...
Same I wanted to say. I bought Start only for the original look.. only thing suitable was tail tidy still we can search for good tail tidy in some biker points
Can you provide me the link of the tail tidy ?
MotoPro Compact Tail Tidy/Fender Eliminator for Husqvarna Svartpilen & Vitpilen 250 www.amazon.in/dp/B0982DNY3S/ref=cm_sw_r_apan_i_Y8SW9JZCPR6M0YF3F4QM?_encoding=UTF8&psc=1
Does the tail tidy hits the wheel hugger if I keeps hugger?
If you mount the tail tidy as it's supposed to fit then yes it will hit the wheel because the gap between the wheel and the number plate has to be more than 5 inches.
If you fix it like how I have fixed then no it will not hit the wheel hugger. I am using it with ktm wheel hugger at present.
@@greyandwhite9730 Did you try the ns 200 number plate holder. I think it is more longer which will not hit the hugger. Even with the hugger I am getting dirt on my shoulder and Helmet. So planning to keep both hugger and the plate holder
@@shameempk007 I did think of using the number plate holder of the ns. But the mounting points for this holder don't match on the husky. You have to drill holes on the underside of the panels to fit it. I didn't want to do it so I didn't try.
Can you share the link for that indicator bracket?
You get it in RE service center just show them the pic or in a parked RE classic front indicator. They will understand. I don't think you will get this online.
@@greyandwhite9730 thank you!
To keep the radiator safe do you know there is something called Radiator guard instead of mounting this mud guard extension that looks horrible
Radiator guards don't make sense to me,
They don't offer complete cover as there are gaps for air flow so there is a chance of radiator getting damaged even with the guard.
They cost 1500 I think it's very close to what a brand new radiator would cost. I would rather buy a brand new radiator instead.
And my biggest problem, you still have to clean the whole thing as it keeps accumulating dirt.
And if you think the mud flap looks horrible,
It cost me just 95rs.
It's keeping my radiator super clean, no mud water has spashed on my radiator after installing it.
It has kept the radiator safe from debris flying off from the front wheel.
In this case I would take horrible looks over radiator guard any day.
Spend your money wisely!
@@greyandwhite9730 if you would take horrible looks over spending money, I think then you should also buy cheap bikes over husqvarna, if you want to add 95 rs cheap things on your bike.
If you want to own a bmw you can’t have a maruti mentality.
@@ankitchahar7091 if the radiator guard is not providing me with what I need on my bike, why should I use it.
If a mud flap is providing me with what I want then I am going to use it. Is this that difficult for you to understand??
Bro do one video for how to fiting
Please
Thanks for the info.
But please try to be more succinct
Sensible mods😊
Hello if you its tyre hugger... Or wnt to sell...i will buy
I’m 5feet 4inch can I ride this bike I have heard that it’s too tall
It's a bit too tall for 5'4" may be. You can take a test ride and see if it works out.
You can ride the bike reducing the preload on the rear suspension that will further reduce the ride height when you sit. As stock the preload on the rear is set to medium.
Personal opinion you will feel difficult to manage it. I am 5 8. Still my complete foot will not touch ground
Bro I'm 5'4 and i own a svartpilen now for 3 yrs and i have no problem with the height.. it's difficult at first.
Where can you buy that tail tidy
www.amazon.in/dp/B0982DNY3S/ref=cm_sw_r_apan_i_Y8SW9JZCPR6M0YF3F4QM?_encoding=UTF8&psc=1
Why don't you tried classic 350 mirrors or dominar mirrors, maybe that fits your requirements 🤔 this doesn't looks good on this high class bike.
Round mirrors have large blind spot. It becomes an issue on the highway. These wide mirrors offer much better visibility.
Lolipop mirrior😂🤣
Are you Tamil?
No
Hindi me hi bat kr le bhai
You better use ur mother tongue
😂
Bekar hai
pulsar leta vo best hai
Hindi
Sorry my hindi is not very fluent.
Ur insta link bro