Clear and simple explanation of how to get it done. I think an important thing to remember is to try to locate a dryer exhaust as far away from an outside A/C unit as you can. Lint blowing out of the dryer vent can clog up an A/C condenser unit in no time at all! Greetings from the USA. Enjoyed your video. Thanks for sharing.
Absolutely awesome stuff. Well edited to keep from being overly long but without skipping any important steps. Some great advice on what tools to use and the tips about putting a screw in to grip and drilling the hole slightly downhill are excellent. Finally, a likeable and clear host. As someone who's just bought their first house, this was an easy subscribe!
Excellent, thanks! One can also use duct seal putty to seal around the vent, which has the advantage of being easier to remove if the vent gets damaged and needs to be replaced. Important to make sure it's sealed very well at the top, because if there's leakage at the top and a good seal at the bottom that will trap moisture in the wall.
WOW that is a hard work way of doing it. I use a 3/8 diameter long drill bit to make a pilot hole from the inside sloping downwards by about 10 degrees right to the outside. There will be a little spalling on the outside brick but that does not matter. Then I use a 4in drill bit with its own internal 3/8 bit which sticks a couple of inches past the end to follow the pilot hole I have already made. The hole is very neat and exactly to size and as it is done in a single action the alignment is exact. Push through solid pipe and then screw covers etc and fill to prevent water ingress. The large drills make the job much quicker and the finish neater. They are not that expensive, I think they can probably be rented but my set includes additional sizes for sink/dishwasher drains and armoured electric cables. It is amazing how many holes you end up drilling into a house.
Those white vinyl hoses are now against code in the USA. You have to use the metallic dryer hose now. The white ones are a fire hazard. Otherwise, great instructional video.
I agree wickedmessenger1....those white plastic hoses are a fire hazard ..However here in the UK manufacturers are still selling dryer with them attached...
As as handyman, I've used this "stitch hole" method many times for up to 12 inch holes with a standard 1/2" hammer drill. Drill small pilot holes around the circumference with 1/4" bit, then enlarge each hole with a larger bit like a 1/2". Definitely slower than a large rotary hammer drill and a diamond hole saw bit. I still can't afford the "big boy" tools and it's out of the question for the DIY home owner. You can rent a professional rotary hammer drill for half a day almost anywhere, but the rental places here will not rent the $300.00 Plus diamond hole saws because homeowners often destroy them.
I baught a 4inch diamond core bit which includes a pilot bit and adapter to use on a standard drill which I already have for £27 off eBay! Less hassle and neater than doing it like he did it
I thought the video was great, I need to do this to my brick home. I purchased it with the dryer venting into the garage and after 8 months I've discovered the problems all that humid air was creating in my garage. My only suggestion, could you please list the parts you used in the video description for you videos such as drill, the bits, the dryer vent kit, etc. Thanks!
Very nice. The only thing I would change is using an aluminum flexible tube from the dryer to the external tube. In many places plastic flexible tubes are not to code.
Great job, but you should drill a single hole right through the centre of the hole from the inside to the outside to give you the reference for the outside hole centre. Just a thought.
Nice one mate. Better for the DIYer as renting or borrowing a core drill is a pain in the arse! PS where are you mate you've not be on in over 7 years..?
Thank you sir. That was the exact tip I was looking to install the duct of my kitchen hood. May I know what is the name of the fitting you installed outside so that I can look for that at the hardware store. Thanking you in advance.
It was not better to use a hole saw? Cleaner and good looking hole plus easier and faster.. 😀 Thanks for sharing anyway. Can I ask why you did not use a sealant or gaskeet between the 2 pipes you put one into the other one?
There's no need to seal the two pipes together they should fit firmly together and not moisture or liquid passes through them so there's no leaks to stop.
Your way to cut the hole slightly downhill was a really good idea. I thought plastic vent duct is already made illegal by local building code. No back draft cover plate on the outside?
Nice video. Nice to see the angle of the hole mentioned also for allowing moisture from the dryer to flow out. Any minimum height as ideally the hose should be angling down to the exit? Was also wondering if a hole saw would be better? Thanks
A hole saw would work fine on the inside. The outside however may prove difficult as it would require a diamond tipped one which could be cost prohibitive. This method is much cheaper even if it is a bit more painstaking. also, I know this is an old comment, but not all viewers will be.
Defeated the purpose drilling a down facing hole if you end up sealing it up on the out side wall side. Wheres the water gonna go, it can't escape? You sealed it up?
That is for a vent not a condenser pipe the vents don't have any moisture pass through from the inside. the sealant and down sloping pipe is to reduce the risk of any external moisture entering the pipe or wall through the whole like heavy rain for example.
To be fair. The best safety gear anyone can have in common sense. If you are stupid and have safety gear on. You will be far worse than someone who has common sense and no safety gear on.
Great video, good sound quality, just amaazed how easy are you drilling with that small drill, is like drilling in a cheese. I got a 3 time bigger Sds hammer drill and take ages to get trough my wall. Thanks for the video!
I have tried using this video for guidance. I have cut a hole in my plasterboard wall only to find some sort of silver material and a horizontal wooden beam that wasn't detected by my stud detector. Any advice?
Great video! Did you use a hammer drill not an SDS drill to do this and what are the dimensions for the long drill bit please and if a hammer drill I presume it had a straight shank? Cheers mate👍
The tip about angling the conduit downwards to let gravity keep moisture from getting in the room/wall is very valuable. Thanks.
i plan to stack my dryer on top of W/M. Will i need to make the hope at the top of that dryer...(probs near the ceiling level?)
Clear and simple explanation of how to get it done. I think an important thing to remember is to try to locate a dryer exhaust as far away from an outside A/C unit as you can. Lint blowing out of the dryer vent can clog up an A/C condenser unit in no time at all!
Greetings from the USA. Enjoyed your video. Thanks for sharing.
I so prefer DIY videos like this, straight to the point clear concise giving you the info you need
One stop shop, I was looking for advise on how to fit a vent into a wall and this is 100% what I needed. Nicely done!
This guy is such a boss, excellent instructional straight to the point
Just check for cables and pipes etc
Many thanks for the video, makes fitting a tumble dryer vent easier when you don't need to use a core drill, didn't realise I could do it this way!
Absolutely awesome stuff. Well edited to keep from being overly long but without skipping any important steps. Some great advice on what tools to use and the tips about putting a screw in to grip and drilling the hole slightly downhill are excellent. Finally, a likeable and clear host.
As someone who's just bought their first house, this was an easy subscribe!
This is a proper tutorial. 2 thumbs up! Cheers from Canada!
Thanks for posting ... my project wasn't a dryer vent, but the tips helped me a lot on my project!
you are one smart guy, I can tell this is not your profession however you thought it thru and mission accomplished...good job dude
Excellent, thanks! One can also use duct seal putty to seal around the vent, which has the advantage of being easier to remove if the vent gets damaged and needs to be replaced. Important to make sure it's sealed very well at the top, because if there's leakage at the top and a good seal at the bottom that will trap moisture in the wall.
Great video - none of the usual ‘like and share’ garbage. Just good info. Worked a treat.
Well done video. Your UK is different than my Texas vocabulary, but your demonstration and recommendations are excellent.
This dude is saving you hundreds between buying a hammer drill and diamond bit and/or renting a setup.
love the sarcasm....love tool rentals
@@jstone1211 what a time waster he must have all weekend 🤭🤭
Excellent, a commonsense, practical demonstration of how to make your calculations for a successful installation.
Really good video, as someone whos diy handicapped this was clear and very helpful. Thanks
This guy is a diy legend! You seem like such a lovely man! Great video!
Awesome. video. I was scared about drilling into my brick exterior but you made me want to attempt it. Thanks
That was useful and instructional. Drilling a big hole in a wall using just regular tools. Thanks.
Thanks for the video, wasn’t sure what was involved with this, now I’m off to buy my appliances. Great instructive video!
8:27 there’s a woman just staring in through the window.
😂😂😂😂
I see her lol
That's the ghost from 3 Men and a Baby...
Peeping tom! 😂😂
It's his neighbour complaining about the brick dust 😂
awesome idea,i will want to buy a core drill bit, but after seen this video i change my mind.thank u.... from Bangladesh
Very nice Cliff! Good job.
You saved me getting a core bit as i only have to drill for two vents long drill bit is much cheeper
Thanks Great video
Brilliant no nonsense video. Well done mate.
WOW that is a hard work way of doing it. I use a 3/8 diameter long drill bit to make a pilot hole from the inside sloping downwards by about 10 degrees right to the outside. There will be a little spalling on the outside brick but that does not matter. Then I use a 4in drill bit with its own internal 3/8 bit which sticks a couple of inches past the end to follow the pilot hole I have already made. The hole is very neat and exactly to size and as it is done in a single action the alignment is exact. Push through solid pipe and then screw covers etc and fill to prevent water ingress. The large drills make the job much quicker and the finish neater. They are not that expensive, I think they can probably be rented but my set includes additional sizes for sink/dishwasher drains and armoured electric cables. It is amazing how many holes you end up drilling into a house.
£100 plus to rent a drill powerful enough for a day.
Clearest instructional ever!
Nice job, simpel way
Thanks for the video! I plan on doing the same thing when installing a portable Heater and AC unit in my workshop.
Those white vinyl hoses are now against code in the USA. You have to use the metallic dryer hose now. The white ones are a fire hazard. Otherwise, great instructional video.
I think it depends where you live. I guarantee you TONS of people still use it.
DEW directed energy doesn't give a F when they want your land!
I agree wickedmessenger1....those white plastic hoses are a fire hazard ..However here in the UK manufacturers are still selling dryer with them attached...
Plastic was never code in North America. They are not meant for heat installs. Only for bathroom venting etc. Not even for range hood venting.
Thanks so much for the brilliant little video. Now I think I can do our install!! (Love your accent)
I'm your 500th subscriber....this is an excellent video.Pity you haven't posted more you would be RUclips success !!.
Nice, clear and no BS. Perfect.
Nice video sir, I have to put a 100mm hole through a brick wall cavity and keep changing my mind between core drill and multiple SDS holes and hammer.
my thoughts about my project were right thanks for the step by step great help im more confident now cheers mate.
Why not use an SDS diamond core bit for a clean hole
nice job. You should do some more videos. This was useful for me when installing an extractor fan for a shower.
I was thinking how can I get the job done with simple tools; and bingo, I've found the solution. Cheers mate/
Impressive organization. Well done!
As as handyman, I've used this "stitch hole" method many times for up to 12 inch holes with a standard 1/2" hammer drill. Drill small pilot holes around the circumference with 1/4" bit, then enlarge each hole with a larger bit like a 1/2". Definitely slower than a large rotary hammer drill and a diamond hole saw bit. I still can't afford the "big boy" tools and it's out of the question for the DIY home owner. You can rent a professional rotary hammer drill for half a day almost anywhere, but the rental places here will not rent the $300.00 Plus diamond hole saws because homeowners often destroy them.
I baught a 4inch diamond core bit which includes a pilot bit and adapter to use on a standard drill which I already have for £27 off eBay! Less hassle and neater than doing it like he did it
Seems like the pipe should be fitted over the outside of the pipe going to dryer instead of inside it.
@@rickeykeeton4770 Absolutely correct. To reduce lint collection at the transition point.
THe last thing you need with a diamond core cutter is a rotary hammer drill
@@johngriffin6624No, with a diamond core cutter, turn off the hammer function and use the rotary function only.
Great. Thank you, some very good tips.
Great video, very encouraging!
Answered all my questions, great video thank you
I thought the video was great, I need to do this to my brick home. I purchased it with the dryer venting into the garage and after 8 months I've discovered the problems all that humid air was creating in my garage. My only suggestion, could you please list the parts you used in the video description for you videos such as drill, the bits, the dryer vent kit, etc.
Thanks!
Just an all round good vid, shows how real people actually get the job done. 👍
EXCELLENT instructions. Easy to understand. Thank you :)
Well done 👍 brilliant video 🎉 the outside cover has it got air flaps so that you don’t get anything coming in spiders mouse etc
Good instruction video, great tips, love it, you make it look easy 😀, thanks
Very nice. The only thing I would change is using an aluminum flexible tube from the dryer to the external tube. In many places plastic flexible tubes are not to code.
Nicely presented project - cheers!
Great job, but you should drill a single hole right through the centre of the hole from the inside to the outside to give you the reference for the outside hole centre. Just a thought.
I'm in the US and I need to do this for my dryer since the past owner put a deck board in front of it. Great info, thanks
Excellent video!!
great diy! thank you!
Great video!
Nice one mate. Better for the DIYer as renting or borrowing a core drill is a pain in the arse!
PS where are you mate you've not be on in over 7 years..?
Nailed it 👌🏻 just what I needed
Thank you. Great information.
Thank you sir. That was the exact tip I was looking to install the duct of my kitchen hood. May I know what is the name of the fitting you installed outside so that I can look for that at the hardware store. Thanking you in advance.
It was not better to use a hole saw? Cleaner and good looking hole plus easier and faster.. 😀 Thanks for sharing anyway. Can I ask why you did not use a sealant or gaskeet between the 2 pipes you put one into the other one?
Hole saw absolutely. They are just not that expensive, you don't have to have an expensive one for a job you may only do once.
There's no need to seal the two pipes together they should fit firmly together and not moisture or liquid passes through them so there's no leaks to stop.
Nice job 👍🏼
Your way to cut the hole slightly downhill was a really good idea. I thought plastic vent duct is already made illegal by local building code. No back draft cover plate on the outside?
Great tutorial. Thanks👍
A bit easier in the U.S. We make our houses out of used popsicle sticks. ;)
😂
😂
😂
Spot the mystery woman in the window at 08.25! Great video, thanks.
Does the internal pipe need to go that high up the wall or can it go lower?
very good informative video
This was great, thank you. How did you know you were drilling exactly dead centre through the exterior brick though? Thanks!
big and very BIG Thanks mate
Great job. Learnt a lot. thanks!
17.41pm how would you do that if you were living on the third floor and unable to get to that outside wall?
Nice video. Nice to see the angle of the hole mentioned also for allowing moisture from the dryer to flow out. Any minimum height as ideally the hose should be angling down to the exit?
Was also wondering if a hole saw would be better?
Thanks
A hole saw would work fine on the inside. The outside however may prove difficult as it would require a diamond tipped one which could be cost prohibitive. This method is much cheaper even if it is a bit more painstaking.
also, I know this is an old comment, but not all viewers will be.
Thanks. Got the job done with this video
Very good job!
Awesome! Thank you! Thumbs up!!!
Thank you!!! We love you, what a dude x
Great job done.👍🏻
I was going to buy a core dril until I saw this!
JUSSTTIINFU3K core drill would lead to a much smoother looking hole to be fair.
@@scottishjimmy9813 It would. But it's permamently hidden, so I don't suppose it makes any difference.
Good video man! I'm doing that for my tumble drier.
Proper job , top marks!
Well done! Thank you sir!
Nice job!
Brilliant video, I now have the inspiration!🙂👍Many thanks!
Thanks for this video
Nice job 👍👍👍👍
Defeated the purpose drilling a down facing hole if you end up sealing it up on the out side wall side. Wheres the water gonna go, it can't escape? You sealed it up?
That is for a vent not a condenser pipe the vents don't have any moisture pass through from the inside. the sealant and down sloping pipe is to reduce the risk of any external moisture entering the pipe or wall through the whole like heavy rain for example.
excellent video, thank you for making it :)
Nice video ❤️👍amazing❤️👍👍😱👍...👍..👍.👍😉❤️😉...🤟
Jesus Christ Ivor. That’s an incredible job. Holy fuck you made it look so easy.
I like how he "advises" the safety gear but---like in the real world---he's not actually using them for the job. ;)
To be fair. The best safety gear anyone can have in common sense. If you are stupid and have safety gear on. You will be far worse than someone who has common sense and no safety gear on.
Cheers for the video. Very helpful. The tips are great 👍
Great video cheers mate!!
great video..
Great video, good sound quality, just amaazed how easy are you drilling with that small drill, is like drilling in a cheese. I got a 3 time bigger Sds hammer drill and take ages to get trough my wall. Thanks for the video!
@8:25 Boss spying on you through the window :)
Ha,ha..You have a very good eyes sight and can see out of a corner of your eyes.
Great video, thank you!
I have tried using this video for guidance. I have cut a hole in my plasterboard wall only to find some sort of silver material and a horizontal wooden beam that wasn't detected by my stud detector. Any advice?
Nice video but why not put the hole in line with the outlet from the appliance to save moisture running back?
Great video! Did you use a hammer drill not an SDS drill to do this and what are the dimensions for the long drill bit please and if a hammer drill I presume it had a straight shank? Cheers mate👍
great video thanks !!!
Brilliant, thank you.