I've used them all and like the hand tamper least because it's so labor intensive and gets such a minimal result. I love to use the vibraplate in true sand, gravel, or rock so long as it has containment, but hands down we go to the Jumping Jack when we really have to hit 90-95% compaction in small areas where we can't get a sheep's foot or roller. Loved the video...
Thanks for this!! Another way to get better tamping is to get heavier duty equipment. Would be interesting to see if the 200lb jumping jack can beat a 1000lb plate compactor. For everyone's reference, based on the product links. weights of items in this video are: - hand tamper 9lb head - plate compactor 207lbs - jumping jack 207lbs Viewers should also note that each compaction type performs better or worse on the type of soil. Jumping jacks are much better on expansive soils (clay) than plate compactors.
I gotta say the slope challenge made me chuckle.. I have a job of repairing sloping pavers in my garden.. the hand tamper wins ! Thanks for uploading this video guys 😊
Actually the rammer probably could have done the slope well, and easily, but by working Across from top to bottom, instead of straight up or down - (thx)-
The bottom line, each of these "tools" has its advantages and disadvantages. I have owned a Wacker plate compactor & jumping-jack compactor for many years. The tool that I strongly favor (as a homeowner with a variety of residential tasks) is the plate compactor, hands down.
Yes the plate compactor is very simple and easy to use. Not a back-breaker. I ended up buying a jumping jack after I made this video, but i'm doing more structural things like footers for my garage and house so I wanted the max compaction I could get. Thanks for the reply!
I was looking for a comparison like this and you made a great distinction with some accessible example situations to share. I am sure the possibilities of various work sites are numerous, but I appreciate the help in forming an opinion about each device in your testing scenarios.
Good Video! A big concept that wasn't mention was that a Tamper/Rammer should be used on cohesive material, and a plate compactor is to be used on granular material.
Use the Jumping jack for moistened soils in trenches and deep fills. Not to wet and not too dry. Dry soils can fool You by looking muddy on the surface while being dry as talc under the muddy surface . Extremely wet , muddy and unstable soils and clay can be stabilized by aeration , addition of gravel and lime or cement . In extremely wet areas permeable base materials may be better suited than those with fine clay binder. To prevent excessive water intrusion into a recent backfill during rain , cover the fill with visqueen plastic sheeting over graded fill that facilitates water flow to sump drainage points where it can be pumped out. Then when ready to finish grade and compact the subsoil with the Jumping jack , the plastic can be quickly removed . Without the plastic rain can quickly add enough water to make drying out the sub base very time consuming and costly. The compactor will be hard to run in the “ plastic “ material becoming unmanageable. “ Pumping “ of the subsoil will reflect into the base and pavement surface. Even if a stable crust can be achieved that facilitates paving it will later shrink and fail as the moisture evaporates out in dry summer conditions causing shrinkage and opening of the joints. A trench pave over such base that is subjected to heavy traffic can also undulate under loads causing a wavy bumpy surface. The J or Jumping Jack Tamper Compactor should ideally begin to rebound as the soil achieves maximum density and stability. First courses of asphalt base Rock can be compacted likewise with regrading to a even surface as the trench come up to paving depth. Then the plate compactor can be used. The initial excavation should be wide enough to allow the plate to fit into it full width. On larger broad areas both roller and plate can be used keeping each lift of material to 3-4 inches thick . Vibration will densify materials but can also bring water up into soils in areas of wet substrate. Narrow trenches of approximately 6” width may save on material cost’s like base and asphalt but are more time consuming to compact with small air powered compactors. They can also be filled with controlled density fill a slurry of sand and cement that will settle and harden . Then the surface width can be increased to a depth of approx 2”-3 “ by a width determined by the Engineer or local specifications to form a T Patch that helps to inhibit water intrusion through the joint. Experience has shown that straight line cuts with rough ground faces are easier to work with , professional looking and the new asphalt when rolled and compacted “ Key” into the existing surrounding surface to form a tighter more impervious bound that resists water intrusion. When patching in excess of 2-21/2 “ of asphalt it is best to do it in 2 lifts . Large areas can be done in one lift either in avg. 2” -2and 1/2 “ or Avg 3” try to get the Base finely tuned for grades with finished surface grade in Mind .
Great video. Did you try multiple passes with the vibration plate to see if that increased the compaction any further? Can you get results similar to the jumping jack after multiple passes with the vibration plate?
Great video mate! You made a good point when mentioned that the jumping jack would be the tool of choice when it comes to applications like driveways in which you need a very solid base. 8:19 been there done that 😄
Ever considered that you can do 3 or 4 passes with the plate compactor for every 1 on the jumping jack with less wear on your body and get possibly deeper compaction minute for minute?
I think there is a point where the plate compactor cannot compact anymore due to the energy it puts out. The jumping jack tamper generates more energy at compaction than the plate tamper. So no matter how many passes you do with either, there is a point where each machine simply cannot compact anymore and it boils down to which can "hit" harder.
It wont happen. Jumper is just too powerful and with a smaller foot, would eat up a plate, even if you ran the plate all day. Mind you, ALL reputable companies use a jumper in ditches where settling is a no no and we have professional soil testers on site who would toss you and your plate out when back filling excavations. We have gone as deep as 21 feet with storm sewers using 2A modified with 12" lifts and never had a compaction fail nor a street settle/sink. There is a big secret to running a jumper. Never push it or fight it, always lean it back about 5 degrees and let it jump its way forward plus, never leave it sit in one spot and dig a hole, In short, keep it moving at its pace, not your pace.
@@Rickimusic I am in learning mode here. I am not disputing your claim but it contradicts everything I am reading about the proper way of compacting different types of material. Cohesive V.S. Granular. If a jumping jack if far superior to a plate compactor in every way, why do they make them? Over compaction is a real thing and can be just as bad as under compaction. Trying to learn and there are very few informative resources on the internet on this subject.
Thank you very much for the video. I am convinced that I will only need to buy a hand tamper from Lowes since it can lead to the same depth result when compared to a plate compactor even though it does take longer to do so. I hate to pay at least $ 500 for a plate compactor, which will have very limited use, and to put it in my already tight garage after recently adding a table saw and a miter saw.
Very helpful data. I am filling in potholes with asphalt millings and wanted to be sure that the jumping jack tamper was the tool for the job. Clearly it is.
I put in a rock pad for a 10 X 16 pre-built building I ordered , do you think the plate compactor would be sufficient enough ? I like the idea of having a nice smooth finish.
all depends on your soil and if had been disturbed. if you put it over ground that was not dug up or disturbed and gave it a good tamp. you should be ok.
I've run a diesel jumping jack that was a lot heavier, that thing packed a punch. perhaps look for one like that. they also make an attachment for excavators to compact if you're super serious about it.
No experience with that particular job, but in construction, we would compact the dirt, then compact stone on top of that. same concept. a plate tamper might be tough manuvering in a stall. i would hand tamp or use a jumping jack
After watching your video I now realize that machine compaction is not practical for my 30 degree slope. Looks like wet compaction with a lot of hand tamping is my best choice aside from a compactor mounted on heavy equipment. I'm installing granite steps. Thanks so much, great comparison, awesome job with the video.
appreciate the video. just wondering if I could use the plate compactor to level my lawn.? I had my irrigation system installed and my lawn is now bumpy because of the tire marks from the machine they used. Thanks
@@mightyconker3903 You can aerate after you have leveled off the bumps if your concerned about it. A rake would work for loose dirt but I'm thinking its sod that has ruts in it and you cant rake that out.
Topcon and CST/Berger are two of the top brands when it comes to rotary lasers. Ive used the Topcon often and like the way it performs. The jumping jack tamper will deliver around 3500 lbf (Pound Force) im not sure what PSI it will deliver as this is not a unit of measurement used to describe the force it exerts
@@appalachiandiy2415 I like the video! If the JJack is 20x20" it is delivering 8 lbs/ in2. The 8x8' Ames tamper in your reference is 0.16 lbs/ in2. The razorback in your demo is about the same. The jumping jack has 50 times the compaction capability; which is obvious with your results.
Awesome video, and answered what I needed. Only have a 7.5 sq metre area that I want to pave, I just cannot justify the cost of the plate compacter when it ends up being nearly half the cost just to rent it (things are not cheap down under). Wanted to know if a hand tamper would be good enough and it seems it will. It's not load-bearing anything just enough to keep the pavers straight.
hmmm. never worked around plastic gas line before so I can't say. I would recommend sand or stone dust for your first lift so you don't have to compact then on your next lift compact. That's just my thoughts but maybe check with guys who do that kind of work. and if you find out comment back cuz I would like to know for myself, Thanks!
Great video, very helpful, thanks for sharing it! Question: can I use any of these machines if it is raining? I am trying to level my yard and compact the mason sand but it doesn’t stop raining. With the hand tamper is not being productive. Thanks.
ramer/tamper, I would say no. It has to much force and you will probably just make ruts. Try the vibe plate. that is the most gentle with little impact force. and Thanks!
Complete Compaction is not measured by depth. A Resistance meter or geoguage is expensive way . One can use lateral forces applied by machine to meet code requirements for complete compaction. Other methods may cause structural sub-base Deficiencies.
The slope test just hurt my back looking at you doing it. I'm sure not everyone has access to one - but you think using a winch or something to help pull it back up the hill could work? Thanks for sharing!
Thanks for sharing this interesting video. I tried the plate vibrator for my decomposed granite patio; I liked it, but it was very heavy to load and unload off my trailer. I'm going to rent a jumping jack tomorrow, because it seems like it will be easier to manoeuvre on my paths. I have a hand tamper, but it's only for awkward spots. That rental yard looks super. I'd use it if I were near by, but I'm in California. Do you think you do a video on using the laser level? Thank you, Daniel
The jumping jack tampers are a little more cumbersome and awkward when loading unloading than the plate tampers. Yes, that seems like it would be a good video for the laser, Thanks for the reply and good luck.
There must be an industrial piece of equipment for slopes, can't imagine a commercial job site having to hand tamp something like that. Video was really good, definitely seems like the plate compactor is the easiest to use overall, although it might drag you a bit. From personal experience I can say the hand tamper is hell on your shoulders and wrists. would love to see if a lawn roller 300-600 pounds is any good.
Yea I don't know what companies would use on slopes. The lawn roller would be interesting but would have to be out in the open and not in tight quarters. thanks for the reply!
@@appalachiandiy2415 absolutely, thanks for the good content. I know for pretty much any thing I'd want to do the plate compactor is the way to go for me unless I had a ranch. I might just buy a lawn roller to see if it will work. Another guy had this lawn leveling tool that looked really interesting too.
@@appalachiandiy2415 this is the guy, fellow RUclipsr with some good info as well. ruclips.net/video/P_nvzs1dCNw/видео.html and the tool ryanknorrlawncare.com/product/lawn-level/
Hello this is a great video. I have to level my ground for a pool. Once I get the dirt leveled do you think the plate would be good enough for an above ground pool?
I would've loved to see if doubling the time with the hand tamper would've achieved a more comparable result to the machines, especially because that would mimick much more what we'd do in the real world.
hmm, in the UK you would never use a "jumping jack" (trench rammer as we call them) for a large area for the obvious reason you show, it produces ridges because it is not the tool for such a job. You were lucky that the compactor plate's engine continued running on that slope, they are supposed to have engine cut outs if the oil level is "wrong" due to use on a slope. I wonder if your hire centre has removed safety features?
Seems like for the slope you could just use an excavator and press, because most buckets are rounded maybe make a special attachment in the shape of a large tamper, make it 4140 steel, maybe 2'x2' and 1/4" thickness, depending on the size of your machine, just so long as it fits the bucket pins/hitch.
@@appalachiandiy2415 is that maybe what we call "State Mix" here in NY? I had some laid yesterday and the guy did not compact it except a little bit of "hand tamping" and I'm researching what should have been done. By the way, I enjoyed your radiant heat video, it inspired me to do mine!
All I can say is , use each tool for the areas each work at the best until you can no longer use it there so's ya don't have to hand tamp 100% of the slope Oh wait this video is years old:) You should be done by now even if you hand stamped it all :) Cool video I just happened on by osmosis or for comparison issues or something like that
I've used them all and like the hand tamper least because it's so labor intensive and gets such a minimal result. I love to use the vibraplate in true sand, gravel, or rock so long as it has containment, but hands down we go to the Jumping Jack when we really have to hit 90-95% compaction in small areas where we can't get a sheep's foot or roller. Loved the video...
Thanks! yea I agree with you 100%
i find that using the hand tamper on asphalt is the best application of the tool particularly in hard to reach spaces for larger equipment
I don’t have a work truck and can’t get a 205 lb plate compactor home. My need is asphalt driveway repairs so hand tamper is only viable choice.
Thanks for this!! Another way to get better tamping is to get heavier duty equipment. Would be interesting to see if the 200lb jumping jack can beat a 1000lb plate compactor. For everyone's reference, based on the product links. weights of items in this video are:
- hand tamper 9lb head
- plate compactor 207lbs
- jumping jack 207lbs
Viewers should also note that each compaction type performs better or worse on the type of soil. Jumping jacks are much better on expansive soils (clay) than plate compactors.
correct, It would be interesting to see weight differences too
This was really useful, thank you, actual data, good comparison on different surfaces, really appreciate the post.
Thank You!
Great job, I learn a lot. You guys spend so much energy doing this video that you should receive an award.
Thank you!
I am so impressed with how thorough you did your comparison test! Thank you for such a usefull video!
@@ibjaime Thank You!
I gotta say the slope challenge made me chuckle.. I have a job of repairing sloping pavers in my garden.. the hand tamper wins ! Thanks for uploading this video guys 😊
haha, thanks
Actually the rammer probably could have done the slope well, and easily, but by working Across from top to bottom, instead of straight up or down - (thx)-
Thank you for this video. Saved me a lot of time and money for renting one for a slope compaction.
The bottom line, each of these "tools" has its advantages and disadvantages. I have owned a Wacker plate compactor & jumping-jack compactor for many years. The tool that I strongly favor (as a homeowner with a variety of residential tasks) is the plate compactor, hands down.
Yes the plate compactor is very simple and easy to use. Not a back-breaker. I ended up buying a jumping jack after I made this video, but i'm doing more structural things like footers for my garage and house so I wanted the max compaction I could get. Thanks for the reply!
@@appalachiandiy2415 any advice on trenc3e
you can see the amount achieved with a hand tamp before he gave up is a good demonstration of the advantage of the plate compactor i.e. more area!
I was looking for a comparison like this and you made a great distinction with some accessible example situations to share. I am sure the possibilities of various work sites are numerous, but I appreciate the help in forming an opinion about each device in your testing scenarios.
Thank You! There wasn't a lot of videos on youtube comparing these, so I figured why not make one.
Black socks and shorts? CLassy. Also a very good comparison video. Have not seen anyone do this, so it was great to see.
Peace Family,
Really appreciated this presentation, keep up the great work.
Respect
thank you for making such comparison on different soil type.
Good Video!
A big concept that wasn't mention was that a Tamper/Rammer should be used on cohesive material, and a plate compactor is to be used on granular material.
Good tip, thanks for the reply
Good video. Really. I’m about to compact soils in a trench and I took away some good info from you. Thanks.
Thanks for taking your time to do this!
Thanks for this! Now I can ignore the people telling me a hand tamper will do next to nothing!
Glad this helped. Its impressive what a little elbow grease can do!
This was so helpfull, we are trying to fix our backyard, and we dont have an idea of any of this. Huge huge help.
Thanks
Thanks!
Use the Jumping jack for moistened soils in trenches and deep fills. Not to wet and not too dry. Dry soils can fool You by looking muddy on the surface while being dry as talc under the muddy surface . Extremely wet , muddy and unstable soils and clay can be stabilized by aeration , addition of gravel and lime or cement . In extremely wet areas permeable base materials may be better suited than those with fine clay binder. To prevent excessive water intrusion into a recent backfill during rain , cover the fill with visqueen plastic sheeting over graded fill that facilitates water flow to sump drainage points where it can be pumped out. Then when ready to finish grade and compact the subsoil with the Jumping jack , the plastic can be quickly removed . Without the plastic rain can quickly add enough water to make drying out the sub base very time consuming and costly. The compactor will be hard to run in the “ plastic “ material becoming unmanageable. “ Pumping “ of the subsoil will reflect into the base and pavement surface. Even if a stable crust can be achieved that facilitates paving it will later shrink and fail as the moisture evaporates out in dry summer conditions causing shrinkage and opening of the joints. A trench pave over such base that is subjected to heavy traffic can also undulate under loads causing a wavy bumpy surface. The J or Jumping Jack Tamper Compactor should ideally begin to rebound as the soil achieves maximum density and stability. First courses of asphalt base Rock can be compacted likewise with regrading to a even surface as the trench come up to paving depth. Then the plate compactor can be used. The initial excavation should be wide enough to allow the plate to fit into it full width. On larger broad areas both roller and plate can be used keeping each lift of material to 3-4 inches thick . Vibration will densify materials but can also bring water up into soils in areas of wet substrate. Narrow trenches of approximately 6” width may save on material cost’s like base and asphalt but are more time consuming to compact with small air powered compactors. They can also be filled with controlled density fill a slurry of sand and cement that will settle and harden . Then the surface width can be increased to a depth of approx 2”-3 “ by a width determined by the Engineer or local specifications to form a T Patch that helps to inhibit water intrusion through the joint. Experience has shown that straight line cuts with rough ground faces are easier to work with , professional looking and the new asphalt when rolled and compacted “ Key” into the existing surrounding surface to form a tighter more impervious bound that resists water intrusion. When patching in excess of 2-21/2 “ of asphalt it is best to do it in 2 lifts . Large areas can be done in one lift either in avg. 2” -2and 1/2 “ or Avg 3” try to get the Base finely tuned for grades with finished surface grade in Mind .
Great video. Did you try multiple passes with the vibration plate to see if that increased the compaction any further? Can you get results similar to the jumping jack after multiple passes with the vibration plate?
Thanks, I'll going to buy jumping jack now first of all, but it's good to have three of them.
If you have the $$$$ yea! Its great to have all 3
5:03 i luv how you get the whole family involved.. lol!
Its always more fun with family!
Great video mate! You made a good point when mentioned that the jumping jack would be the tool of choice when it comes to applications like driveways in which you need a very solid base.
8:19 been there done that 😄
HAHA dude that sucked pulling that stuff up the hill! Thanks for the reply
filling in a trampoline hole and turning into an eventual fire pit. going with the jumping jack. thanks for the video
cool! no problem, thanks for the reply
Thank you for this great video. Helped a lot in determining what to use for my garage pavers.
Great! I'm glad it helped
Great laser! I bought the same one years ago.
Yes, I use mine a lot
Ever considered that you can do 3 or 4 passes with the plate compactor for every 1 on the jumping jack with less wear on your body and get possibly deeper compaction minute for minute?
I think there is a point where the plate compactor cannot compact anymore due to the energy it puts out. The jumping jack tamper generates more energy at compaction than the plate tamper. So no matter how many passes you do with either, there is a point where each machine simply cannot compact anymore and it boils down to which can "hit" harder.
It wont happen. Jumper is just too powerful and with a smaller foot, would eat up a plate, even if you ran the plate all day. Mind you, ALL reputable companies use a jumper in ditches where settling is a no no and we have professional soil testers on site who would toss you and your plate out when back filling excavations. We have gone as deep as 21 feet with storm sewers using 2A modified with 12" lifts and never had a compaction fail nor a street settle/sink. There is a big secret to running a jumper. Never push it or fight it, always lean it back about 5 degrees and let it jump its way forward plus, never leave it sit in one spot and dig a hole, In short, keep it moving at its pace, not your pace.
@@Rickimusic I am in learning mode here. I am not disputing your claim but it contradicts everything I am reading about the proper way of compacting different types of material. Cohesive V.S. Granular.
If a jumping jack if far superior to a plate compactor in every way, why do they make them? Over compaction is a real thing and can be just as bad as under compaction.
Trying to learn and there are very few informative resources on the internet on this subject.
Thank you very much for the video. I am convinced that I will only need to buy a hand tamper from Lowes since it can lead to the same depth result when compared to a plate compactor even though it does take longer to do so. I hate to pay at least $ 500 for a plate compactor, which will have very limited use, and to put it in my already tight garage after recently adding a table saw and a miter saw.
Great! I'm glad this video helped you out. Storage is always a huge problem, finding room for all of our toys!
Is tool rental an option where you are?
The nearest store that have tool rentals is 100 miles away. Rental is my last resort anyway.
@@joekelley1734 Yes, there are multiple stores that offer tool rentals
@@passion830217 Man! that sucks.
Wow! Great informative video. Thank you for taking the time to do this video for people like me who don't know. God Bless you.
Thank you!
great test buddy. I hope you are well. keep it up.
Thanks
Building my own house and about to compact my footer down with some powdery gravel. I think I will use a cheap jackhammer with a tamper bit.
So the little guy is the chief giving instructions how you do the work.
@SY haha yea he like to find his way into the vids
@@appalachiandiy2415 I believe so!
Can i use ramer/jumper inside house?
I am worried about vertical foundation, as displacing soil could damage it.
What you think?
just stay about a foot away from it. Are you going to pour a slab? Also, make sure you got some good ventilation if gas powered
Thanks for the great comparison!
Absolutely!
Should you wet soil before you start to compact?
great title,r u still active posing on yt
I try to post at least once a month
Did I just find the legendary thingamabob?
Very helpful data. I am filling in potholes with asphalt millings and wanted to be sure that the jumping jack tamper was the tool for the job. Clearly it is.
What if you're making a footing that's 4 feet deep? Is the only option a hand tamp?
ohh, well yea prob, unless you can get an attachment tamper for a mini excavator
Great video! Just what I was looking for.
Great! glad it helped
I put in a rock pad for a 10 X 16 pre-built building I ordered , do you think the plate compactor would be sufficient enough ? I like the idea of having a nice smooth finish.
all depends on your soil and if had been disturbed. if you put it over ground that was not dug up or disturbed and gave it a good tamp. you should be ok.
Thank you for making this video. Very helpful!!!!
Awesome tests. Very helpful data.
Thank You!
Do you have a video on that cool laser level??
I do not as of yet. I use it a lot actually and its super handy and not all that expensive. hammerhead is the brand
Awesome job showing all the strengths. Was hoping the jumping jack would do better on a slope - have some pond banks I want to compact!
I've run a diesel jumping jack that was a lot heavier, that thing packed a punch. perhaps look for one like that. they also make an attachment for excavators to compact if you're super serious about it.
Great video. This matches with my engineer recommendations.
That's Great!
Any experience compacting soil and then gravel (5/8 minus, for example) under horse stall mats?
No experience with that particular job, but in construction, we would compact the dirt, then compact stone on top of that. same concept. a plate tamper might be tough manuvering in a stall. i would hand tamp or use a jumping jack
Yes that would work add a lift of 3/ minus first in top of your soil then a thinner life of 5 minus
Thank good to see in use but you didn't address the different soils . clay /cohesive vs sandy
They have air powered hand tampers that have different tamping plates.
thats interesting, I've never seen one of those
After watching your video I now realize that machine compaction is not practical for my 30 degree slope. Looks like wet compaction with a lot of hand tamping is my best choice aside from a compactor mounted on heavy equipment. I'm installing granite steps. Thanks so much, great comparison, awesome job with the video.
Thank you! Wow a 30° slope! That will suck to hand tamp for sure. Good luck
I have to regrade a front yard to add a slope. Ideally I’ll do it over the course of a month or two. Would you recommend the Jack or the compactor?
Great video - very useful advice. Surprised at the jumping jack
Thanks! The jumping jack does pack a punch!
appreciate the video. just wondering if I could use the plate compactor to level my lawn.? I had my irrigation system installed and my lawn is now bumpy because of the tire marks from the machine they used. Thanks
Thanks! Yea a plate compactor would work good for the high spots but if there are deep ruts you might have to add some fill.
thank you. I appreciate your response.
@@ryanhizon9546 Absolutely
Bro if you compact the soil the grass won't grow well. Better to use a take to level soil
@@mightyconker3903 You can aerate after you have leveled off the bumps if your concerned about it. A rake would work for loose dirt but I'm thinking its sod that has ruts in it and you cant rake that out.
Glad I watched. I would of thought the plate compactor would win out.
It is way better for speed, but for compaction, the tamper is the best
If I am 5’1” @130#, female. Will I be able to handle the jumping jack easily?
What kind of laser you use , Which one would you recommend if laser , the best compactor you show ,how many pounds of pressure does it impact?
Topcon and CST/Berger are two of the top brands when it comes to rotary lasers. Ive used the Topcon often and like the way it performs.
The jumping jack tamper will deliver around 3500 lbf (Pound Force) im not sure what PSI it will deliver as this is not a unit of measurement used to describe the force it exerts
@@appalachiandiy2415 I like the video! If the JJack is 20x20" it is delivering 8 lbs/ in2. The 8x8' Ames tamper in your reference is 0.16 lbs/ in2. The razorback in your demo is about the same. The jumping jack has 50 times the compaction capability; which is obvious with your results.
Thank you. looking for something like this.
Your welcome!
8:19 You need a backhoe or excavator to pack a slope. A roller (hand power or driven) is too risky too.
Yea you can do it that way but many people do not have access to machinery like that or know how to run it well
Awesome video, and answered what I needed. Only have a 7.5 sq metre area that I want to pave, I just cannot justify the cost of the plate compacter when it ends up being nearly half the cost just to rent it (things are not cheap down under). Wanted to know if a hand tamper would be good enough and it seems it will. It's not load-bearing anything just enough to keep the pavers straight.
Nice, yes plate compactors are expensive. I typically always rent too
Awesome content! Can I use a jumping jack to compact a 12 inch lift on a plastic gas line?
hmmm. never worked around plastic gas line before so I can't say. I would recommend sand or stone dust for your first lift so you don't have to compact then on your next lift compact. That's just my thoughts but maybe check with guys who do that kind of work. and if you find out comment back cuz I would like to know for myself, Thanks!
Hi guys
am in need to buy manuel compactor and ones with sterring
where do you live? country?
Great video, very helpful, thanks for sharing it! Question: can I use any of these machines if it is raining? I am trying to level my yard and compact the mason sand but it doesn’t stop raining. With the hand tamper is not being productive. Thanks.
ramer/tamper, I would say no. It has to much force and you will probably just make ruts. Try the vibe plate. that is the most gentle with little impact force. and Thanks!
Complete Compaction is not measured by depth.
A Resistance meter or geoguage is expensive way . One can use lateral forces applied by machine to meet code requirements for complete compaction. Other methods may cause structural sub-base Deficiencies.
Super scientific! Yea this was just a simple comparison to how they operated and compacted. Thanks for the reply
The slope test just hurt my back looking at you doing it. I'm sure not everyone has access to one - but you think using a winch or something to help pull it back up the hill could work? Thanks for sharing!
Yeah that could work
@@appalachiandiy2415 Cool! I've never done it, but I'm not so young... so I'm always looking at other ways to not break my back. LOL
Very helpful and self explanatory video
Keep it up bro
Thanks!
Thanks for sharing this interesting video. I tried the plate vibrator for my decomposed granite patio; I liked it, but it was very heavy to load and unload off my trailer. I'm going to rent a jumping jack tomorrow, because it seems like it will be easier to manoeuvre on my paths. I have a hand tamper, but it's only for awkward spots. That rental yard looks super. I'd use it if I were near by, but I'm in California. Do you think you do a video on using the laser level? Thank you, Daniel
The jumping jack tampers are a little more cumbersome and awkward when loading unloading than the plate tampers. Yes, that seems like it would be a good video for the laser, Thanks for the reply and good luck.
Thank you so much for sharing
There must be an industrial piece of equipment for slopes, can't imagine a commercial job site having to hand tamp something like that.
Video was really good, definitely seems like the plate compactor is the easiest to use overall, although it might drag you a bit. From personal experience I can say the hand tamper is hell on your shoulders and wrists.
would love to see if a lawn roller 300-600 pounds is any good.
Yea I don't know what companies would use on slopes. The lawn roller would be interesting but would have to be out in the open and not in tight quarters. thanks for the reply!
@@appalachiandiy2415 absolutely, thanks for the good content. I know for pretty much any thing I'd want to do the plate compactor is the way to go for me unless I had a ranch. I might just buy a lawn roller to see if it will work. Another guy had this lawn leveling tool that looked really interesting too.
@@michael95621 huh, sounds interesting with the lawn leveling tool
@@appalachiandiy2415 this is the guy, fellow RUclipsr with some good info as well. ruclips.net/video/P_nvzs1dCNw/видео.html and the tool ryanknorrlawncare.com/product/lawn-level/
That is neat. thanks!
Hello this is a great video. I have to level my ground for a pool. Once I get the dirt leveled do you think the plate would be good enough for an above ground pool?
I think a plate will work good. tamp the dirt and then tamp your sand on top to make it nice and smooth
@@appalachiandiy2415 👍🏼 thanks for the reply!
Really useful video - great post!
Thank you!
Putting down stone for a carport parking pad. Want to rent a plate compactor but after checking rental prices, I'll be hand tamping 😂
Aww man! Buy some Tylenol then
Thanks for the great video 😊
I would've loved to see if doubling the time with the hand tamper would've achieved a more comparable result to the machines, especially because that would mimick much more what we'd do in the real world.
Need the jumping jack coat to buy.
My is damage.
hmm, in the UK you would never use a "jumping jack" (trench rammer as we call them) for a large area for the obvious reason you show, it produces ridges because it is not the tool for such a job.
You were lucky that the compactor plate's engine continued running on that slope, they are supposed to have engine cut outs if the oil level is "wrong" due to use on a slope. I wonder if your hire centre has removed safety features?
Correct. Its mainly for footer compaction or somewhere you need the highest compaction in a small area.
Great video, very helpful, thank you!
Thanks!
how much does compaction impact a patio slab?
I haven't even gotten into the video yet but appreciate you doing this video it's exactly what I was looking for
Seems like for the slope you could just use an excavator and press, because most buckets are rounded maybe make a special attachment in the shape of a large tamper, make it 4140 steel, maybe 2'x2' and 1/4" thickness, depending on the size of your machine, just so long as it fits the bucket pins/hitch.
Yes if you have an excavator. They also make tampers that are hydraulic driven and fit onto the arm of an excavator.
Thanks for your job guys.
Absolutely
Good compersion
Thank you!
Gran video , gracias por la información
I think doesn't start tamping until 2:30
yes, if you're interested in seeing just the tamping go to 2:35
What is "modified"?
Modified is 2A stone. It's a mixture of 2" down to stone dust. It packs hard and is used under driveways and foundations.
@@appalachiandiy2415 is that maybe what we call "State Mix" here in NY? I had some laid yesterday and the guy did not compact it except a little bit of "hand tamping" and I'm researching what should have been done. By the way, I enjoyed your radiant heat video, it inspired me to do mine!
Excellent Video. Many thanks.
Thank you!
That slope was quite extreme, do you think the plate compactor would have worked in a less steep slope?
Pls I need this machine in Nigeria to start up a small renting business
Great video. Thank you.
Thanks!
Very nice friends ❤️🙏🙏
In the first test, I wonder if the jumping jack woulda left fewer ridges if the soil was drier.
that's possible, it tends to still leave a more uneven pattern than the plate compactor
You need a vibratory roller or an impact compactor behind a tractor to truly compact the soil.
Great Video!
Thanks
Has anyone tried using a jack hammer with a tamper attachment?
Awesome video love the fam in the video wil subscribe thanks
Thanks! Yea they tend to get wrangled in some times
Sideways on the hill😅 Nice video
Yea that was kinda tough!
Great Experience.
Yes it was!
All I can say is , use each tool for the areas each work at the best until you can no longer use it there so's ya don't have to hand tamp 100% of the slope
Oh wait this video is years old:)
You should be done by now even if you hand stamped it all :)
Cool video I just happened on by osmosis or for comparison issues or something like that
Haha, might have just finished up with the slope. That would have taken forever
@@appalachiandiy2415 Ohhhhh yea !!
without question no matter how ya slice it.
that was a difficult grade !
I thought you're supposed to run the jumping jack and then the plate compactor
Alot depends on what your doing. Most will compact dirt/2A stone with the jumping jack then plate vibe finer stone on top
Very helpful.
Thanks!
Precio?