Thanks sooooo much for this. Just replaced my E8 brew group with your super instructions and it works perfectly again. I was stumped on how to get the thing to come apart. Cheers!!!
thank you for such a great range of videos, as a retailer of Jura in australia you give us better information than the company themselves. I would recommend your services to anyone.
Thank you very much. Your are very good at what you do. This time I have been able to open and clean the machine myself. I will order some parts from your company. You are the best!
As the rest of the viewers. THANK YOU so much for putting these videos available. I just cleaned and refurbished my C65 brew group. However, now the brew group is noisier than before. Is there a tip in the reassembling and mounting that can reduce the noise. Once again, thank you so much for these great Jura training videos.
for Jura E50 I can't find anywhere what gasket is needed for steam valve connected to thermoblock? No picture no info, nowhere. I have there serious leaking hot water under pressure and can't find what is needed there, what type. Could you help me please?
Thanks for your helpful video. I cleaned and reassembled the brew group on my E50 with your help. When I power it up it runs an initiation sequence and finishes with all flashing lights. Any assistance would be much appreciated.
+velotique Do you get hot wter when you operate the machine? Also, the brew group could be incorrectly installed resulting in flashing lights. Please re-do the installation and see if that helps.
+Parts Guru Thanks for your quick response. The brew group was miss-aligned. Fixed it. It would be useful to show how to align the brew group by running through the brew cycle. Thanks, I appreciate all your help.
+velotique I'm now getting water leaking out the bottom of the brew group when coffee is extracted. Water runs out of the drain valve when I switch to steam or water from steam wand. The water line connections to the drain valve is good. Is it the steam/brew solenoid valve or micro switch? Or is it the drain valve on the brew group? Thanks for your help.
Excellent demonstration! My Jura Impressa E9 leaks water at the frother side. The membrane regulator is rusted. How do I take it out to replace it with a new part? Thank you.
+937tubeyou Hello: here's the link to the video that demonstrates how to replace the Jura membrane regulator in Jura E9: ruclips.net/video/tarVahYAR1k/видео.html
This is a a very clear and helpful video which has inspired me to try my hand at cleaning and refurbishing my unit. There is one problem in particular. The spouts appear to be partially blocked with reduced flow and backing up of the coffee so that it spills out between the two spouts. Is there any easy way to fix this problem without dismantling the entire machine? Thank you.
I just finished the refurbishing and cleaning of the brew group C3000 and the malfunction 8 error is now eliminated!! Many thanks for the tutorial it was a blessing to us. Now however, no water is reaching the rinse cycle or entering the grounds, do you have any suggestions. Thank you for the fast delivery of the o-ring sets. What a great service this is!
Hi. I gave it my best shot and took apart the machine, changed and oiled the oil rings and had all the right tools. Alas, when I turned it on my machine made an absolutely horrible sound and then returned to E8. I thought I had followed your directions carefully but I guess not. It's quite possible that I reversed an item while assembling the brew group. Whatever it was, I failed and the thought of disassembling again to find the problem seems overwhelming. It would have been great to have a reassembly video as opposed to watching the disassembly and thinking in reverse. Thanks anyway. :))
+Mary Christine Andrews Hi, the Jura brew group disassembly video is also posted, please click the link below to watch the Jura brew group reassembly video. Hope it helps: ruclips.net/video/W1n7jT6_kEA/видео.html
Hi, We have a Jura Grinder Burr replacement video posted on our RUclips channel. Please watch it to learn how to clean the grinder in Jura espresso machines.
Good evening, I have a Jura E75 and from time to time the coffee ends up in the bottom tray under the coffee grounds. It does not flow from my 2 holes. What could I do. Thank you, Adrian
C9 is similar internally as Impressa E8, E9. It has a solenoid valve located below the thermoblock to control steam/hot water flow from the cappuccino spout
Thank you for the video! Unfortunately I broke a piece off the when trying to get one of the side panels off the brew group. Do you know if it is possible to buy just this part? I glued it and put it back together without difficulty but am worried it is not going to hold.
Parts Guru Hi, it is the left (water tank side) piece. I put everything back together after cleaning and lubricating as you showed (with the glued piece which appears to have held), but it does not work--the error 8 message still happens. I took the top back off and tried to see the problem--the large piston is going up and down as it should several times while machine says heating or rinsing but apparently it cannot progress from there. Not sure if I should take it apart again or look into replacing the whole brew group? Can you tell me the cost for this? Or should I just send it to you at this point?
Cheryl W You may have missed a step during re-assembly. You should re-assembly it correctly by watching our brew group re-assembly video. Depending on how old the brew group is, you may want to replace it with a brand new one. Here is the link to purchase a brand new brew group: www.shop.partsguru.com/Jura-Brew-Group-Impressa-C-E-F-S-Series-0010507.htm We are here to help, should you have more questions.
Very informative video. The issue with my E8 is that the display is stuck at the "Empty Grounds" message. There are no grounds, and nothing I do seems to be able to get the machine to move beyond this message. Is there a sensor that may be stuck or need replacing? If so, where could I find it?
Eric Roman Used coffee grounds are collected in the used coffee container. If the display shows EMPTY GROUNDS, no more coffee can be made until you empty the used coffee container. • Carefully lift and remove drawer since there is water in it. The display shows DRAWER MISSING. Important: Do not unplug the machine while you are emptying the coffee grounds. • Empty the used coffee container and the drawer. • Push the drawer back into the machine. The display still shows DRAWER MISSING. • Place the used coffee container on the tray and insert back into the machine. The display shows READY and you may now continue brewing coffee.
Parts Guru Thanks for the reply. The problem I am having goes deeper than that, unfortunately. I have had the machine for almost a year and a half, and have emptied the grounds container many, many times, so I am familiar with the procedure you outlined. However, the machine is now stuck at the EMPTY GROUNDS message. When I remove the drawer, no DRAWER MISSING message appears. The display stays at EMPTY GROUNDS. There are no grounds to empty. So I was wondering . . . is there a sensor that might be clogged or need replacing?
Eric Roman Pull out the drip tray, and remove the used coffee container. Wait 10 seconds, reinsert the tray without the used coffee container. See if the message disappears. If it does, then pull out the tray again, wait 10 seconds, and replace the used coffee container and reinsert the tray. Perform the above while the machine is on. Hope the above helps!
Just trying to get an answer on the following question: In order to get a fullsized cup of copy my E45 produces only about or less than 1 cm in a normal cup; this has happened since I had overcome the problem with the cleaning program. What could be the cause of this failure? The electronics?
(Answer took a while because of problems with pc) I do not recall why after several efforts the cleaning program came to an end, but after that had happend the aforementioned problem occurred. I you could give me a clou as to where I have to look (after opening etc the machine, I would have the need of the special tool and the appropriate service manual)
I have seen your Jura E85 Brew group replacement. I have also a Jura E85 and I have a problem with the coffeemachine E85, because the coffee contains less beans, so the coffee tast to much watery. I think the coffeemill/grinder grinds to less beans. How can I repair this? There are enough beans in the machine.
Hi again got a new pump in my jura impressa E40 and heats water, but the problem now is when I plug it into mains the water flows non stop in coffee brew and when I switch it over to steam/water nozzle water just flows all the time.
+Totlino Totolonio I think you have reconnected wires wrong to the pump or to magnet valve which is on the same circuit as the pump. To check if pump is being powered by any shorted function in the machine, you should turn the machine off. Disconnect one wire on the pump to isolate the disconnected wire. Turn power to the machine on and see if the pump is still on. If so, then the machine is grounded.
Tyred the wires again as you said,but still same problem. Only when I disconnect a wire then pump stops, but when I press button for coffee I have to put the wire back on so water flows then after coffee brewing is I have to disconnect the wire again or the water flow keeps on flowing.
Hi, You've done the difficult part i.e. removing side panels. The hooks on the side panels are locked into the slots at the top and bottom of the sides.
+Parts Guru Yes, we see it all and when we lock in all the parts, the panels won't move all the way forward so that the hole for the screws on top don't line up no matter how we push or try to move panels. Thanks again for your great video. I am going to post it on my blog, shelleysays.com.
Please ensure the two side panels locking tab in the front of the machine (below the coffee outlet) are pulled down. This allows the side panels to slide all the way to the front. The side panel would not snap in into the locks at the front.
+Shelley Garfinkel I just posted on my blog if you want to read it and comment. I can always edit: www.shelleysays.com/2015/12/super-automatic-coffee-machines-are-not.html
Hi , thank you for your usefull and proffesional pesentation . My problem with my jura c5 is that when i start making my coffee i press the boton and water goes into the tray instead of coffee cup . Then i press the water cleaning boton and no water poors . I repet the water push boton and after 4-5 times water starts . And then i can try to make coffe again and maybe coffee is coming to the cup . If not , no water is coming , the coffee grind is dry in the beem and more water is in the tray . And i start again by trayng to rinse . What is the cause of this ?
Thanks for the Video, just have a question regarding the Jura grinder and wondered if you might know the answer. After accidently putting wet beans in the grinder and trying to make a coffee, I took the grinder apart using your video, cleaned out the caked coffee and put it all back with exception of one very small bearing and spring. (So in total mine had 4 springs and 4 bearings)The other 3 bearings and springs were larger and obvious where they needed to go but I reassembled the unit and all seems to work for 5 coffees now. Any ideas where this would go or for what purpose it serves ?
Teal'c Herman Hi, Are you able to firmly seat the torx screw driver into the screw itself? Try T25 and see if that helps with the firmer grip. Avoid stripping the screw.
Parts Guru Thank you very much for your reply, "I called a friend" who is stronger than me, he managed to unscrew them, it turned out both screws were glued in. Your videos are perfect, I managed to open the machine clean it, disassemble the Brew Group clean it lubricate it and reassemble it, put everything back together and try it unfortunately it still doesn't work and the message that keeps flashing is "switch open" any idea what that means please?
in my Jura E70, coffee does not come out of the spout, noticed the water does not get mix with coffee, coffee grounds go in the container below and water goes in to the tray, the magnet at the bottom of the brew group and the cubical unit does get pulled in like it suppose to, all lines appear to be open, what else can be checked in the coffee machine to fix this problem, appreciate any help.
Ebbie Attar Check the fineness of the used coffee. Is it too fine like flour or table salt grain? Perhaps the grinder burrs need to be replaced. They are likely to be blunted and do not grind enough coffee.
Hi Parts Guru I have a Jura Impressa s9 with the new style jura fine foam frother fitted, When just making a normal coffee, the Frother has started to leak out water at the same time, any ideas please
Hi Guru. I have S9 and this morning it stops producing coffee and espresso. screen said brewing and then enjoy like normal, but nothing coming the machine. any idea?
Hello Parts Guru...Great stuff thanks! I seem to be having trouble with my C9. We use it about 10 times a day to make cappuccinos and have noticed lately that the automatic frother has been having trouble continuing to make froth for the entire 20 seconds. for the first while it is fine and then starts to just spit steam and there is barely any milk entering the system. I have checked the seals on the milk container all the way to the machine and they seem fine. Pump replacement? cleaning? any suggestions? thanks
Hello Kolin, Please clean the cappuccino system thoroughly using the Jura cappuccino cleaner. Is this the only issue you are experiencing? Descaling the machine thoroughly should help as well.
I keep getting the Error8 message all the time on my E8 Jura. If I wait overnight, the machine usually fixes itself, but it happens daily. Great video. Can you tell me materials I need to try to fix it myself? It's soooo expensive to send it out for repair that I am ready to take the plunge and give it a go with your video support. Thanks!
Hi: Its time to rebuild the brew group. 90% of the times, Error 8 results from malfunctioning brew group due to worn out piston seals and o-rings. We sell a complete brew group tune up kit inckuding the oval head tool that you can purchase by clicking the link below: shop.partsguru.com/Jura-Brew-Group-Maintenance-Kit-0010729.htm Also, we have posted a RUclips video that demonstrates how to disassemble and reassemble the brew group. We're here to help, should you have more questions.
Great video. Since I have the E8 and will keep it. I can make sure it is super clean. How often should one clean the inside of their machine? Is there a recommendation for every 6 months or ?? I am going to replace those oval screws with Torx screws.
I called in with this problem and one of the techs had me go through the cleaning cycle and use a toothpick to clear out both spouts, while the water is rinsing through, slide the adjustable spouts up and down to flush any clogs out. it worked for me. A big glob came out the clogged side. I periodically slide it up and down during the cleaning cycle while there is liquid coming through now.
Hello, I have a Jura impressa J6. I waited for 1 week to get the tool for my machine. The computer comes on and says that I should fill the beans. I know that there is probably oil and beans in the grinder. We finally received the tool to twist the grinder but it jumbles the beans still are not going into the grinder. Our Jura is 1 year old and so I know that we should open it up and do something. I don't want to send it to Jura. This is too frustrating!!!! Please can you help. Should my husband open it up and remove the grinder? I don't know. Please reply...
Hi there. My Jura S9 is giving problems with the milk Frothing and heating. It seams like the steam pressure is too low to develop a stream of milk flowing. We've tried to do a cuppachino cleaning or descaling, but not enough pressure to even suck the solution through the throth-ing device. The rotatory switch don't want to adjust the amount/duration of water flow. Any suggestion on what the problem might be?
I followed this and successfully removed the Brew Group from my E80, gave it a good clean and put it back. However, now when I turn the machine on, the motor runs moving the brew group up the screw to the top and then the motor continues making a horrible grinding noise. When I looked closely, the long cylindrical cog that is removed with the brew group is not turning, but the cog that drives this is. I tried to manually wind the brew group back down to the bottom and try again, but the same result - it moves all the way to the top and then tries to carry on going! Any ideas on what to do? Does the motor stop when it CANNOT turn any more, so the issue is that the brew group isn't quite in place so there's a little "give" allowing the small cog to keep turning, albeit noisily. Or is there some kind of sensor that alerts the machine when the brew group is in position that is failing, so the motor continues turning?
@@enriqueyescascruz9907 Of course, I'll try. For starters the grinding noise was because when the brewgroup reached the top, it could go no further, but because the motor didn't stop, it broke the plastic around one of the two screws on the other side (they hold the motor against the tall metal cylinder that drives the brewgroup up and down). Before I could do anything else, I needed to fix this. You may have the same issue. I used a combination of superglue and araldite to cement it back together. As far as the brewgroup itself went, I removed it again and followed this video: ruclips.net/video/W1n7jT6_kEA/видео.html and this time made sure it was in "home position" before reinstalling it. This time when I turned the machine on, it worked perfectly. I hope you have the same success!
quick question. The grinder in my jura machine gets backed up in the grinder(square channel). took the whole grinder pieces and cleaned really good and made sure its dry(not greasy). first brew, thru the grind far out, second brew got backed up in the square channel again. what can cause that? Thank you
Hi, great video, thank you. I was getting error 8 on my C9, I was able to disassemble clean and reassemble the machine, thanks to your videos. But I still have an issue. The machine still makes coffee, but there is a very loud noise from the motor after the coffee is poured and when it ejects the coffee ground it has not been compacted and is still loose. Any help would be appreciated.
Hi Stephen, Please ensure that small white gear on the motor is properly seated in the vertical guide. Check that brew group motor is properly fastened and should not wiggle.
Parts Guru hi, thank you for your response. Everything is seated perfectly and when the brew group is out it moves freely. I have even fitted a new encoder, still the same.
As for the loose coffee grounds in the container, I suggest you adjust the grinder setting to coarser. Make three coffee for the new setting to take effect. Let me know if that helps. By the way, how many cups of coffee have you made on this machine? When was the last time you cleaned the grinder chamber and replace the conical grinder burrs?
Parts Guru thank you so much for your advice, I stripped the brew group down and I had missed some hardened coffee pieces. So now it makes coffee perfectly, unfortunately I now have another issue. When it rinses no water comes through, I’ve checked all the connections and the water comes through when making coffee just not when rinsing.
Hi Parts Guru, my Magimix R500 is just like this machine. When you try brewing the coffee, the sound coming from the pump begins to fade out and trhe whole proccess stops. Is it possible there is a blockeage in the inlet to the brewing unit? It doesn't have the problem while pumping hot water. Cheers-Jorge
Hello Jorge, what happens when you run the hot water cycle? Do you get steady stream of hot water? You also want to check the fineness of the ground coffee beans. If the ground beans are too fine like flour then you need to adjust it to coarser setting like table salt grain. Please feel the fineness between your fingers. Adjust it each notch towards coarser setting. Make three espresso's for the grinder setting to take effect. It's important to adjust the grinder while the grinder is engaged. Hope the above helps!
Please, can you help me with my Jura Impressa e8? It is asking to fill beans when it has beans inside already. Because of that, it doesn't make coffee. What should I look for here as a problem?
Hi Patricia, Did this issue suddenly start? Were you able to make coffee using the grinder? How long have you had this machine? And, when was the last time it was serviced?
I just finished installing the Jura brew group because I had an error 8 message. When I was done I went to use it and now it reads filling system and open tap and I can not make it do anything different. Can you tell me what I could have done wrong.
Please help me : my Jura C5 is making expresso occasionally : water is drained through the drainage valve and not going through the Brewer unit. Is the same when trying to drain ; drains through the drainage valve and does not go to the coffe cup. This happens 80% of time.... I guess is the driange valve which is occasionally leaking ?
Hi Marc, The drainage valve has a white cap that is pressed against the magnet valve needle. The cap is attached to the stem of the spring loaded metal shaft that, when pressed, allows the hot water from the thermoblock into the brew group. Please ensure the drainage valve is properly aligned with the needle on the magnet valve.
I dismantled the drainage valve (ordered the gaskets), put some silicone paste, but still occasionally the drainage valve does not close. When removing the electro valve and acting manually with a screw driver works fine. Looks like to be the electro valve failing, but really strange, maybe still pushing a little sometimes on the white cap. really confusing.
Hello. When i activate my Impressa E60 machine no water or coffe comes out of the coffee spout. The machine makes normal sounds but the water and coffee ends up in the container and drip tray. What can be the problem here.
Great stuff. However I opened it. and it does operate the brew system, but it makes a lot of noise, so maybe it needs calibration? And then it keeps showing No beans all the time. How does the machine know there are no beans? Where is the detector located? I plan to use it with coffee powder so don't care about beans.
+Peter Vekinis Hi, please rebuild the brew group while you have it opened. Replace the brew group piston o-rings and properly lubricate it with food grade lube. The brew group rebuild video is also posted on our channel. The grinder burrs are probably blunted so it doesn't grind coffee beans. You should consider replacing the grinder burrs to start using the freshly ground beans. Try our 50 50 Buzz espresso beans blend. I think you'll like it. Sample is available for free with purchase of parts.
Hello Parts Guru. I have a Jura Impressa E9. A few days ago my machine ceased to work. When I switch on the on the display appears the inscription "Open Top" when I'll do it on the display appears the inscription "Filling System", the machine makes a lot of noise and nothing happens. After about 30 seconds the display appears the inscription "Shut Top". Can anyone help me solve my problem. Thanks
+Andrew Piet Hello, the Open Tap issue is related to the steam valve that's mounted above the boiler and right behind the hot water/steam knob. The cause of malfunctioning is lack of Descaling the machine. If you're using Clearyl filter cartridges, please stop doing so. It's a waste of money. The Clearyl filter removes bad tasting elements from water; it doesn't remove calcium. When the machine is not descaled properly then calcium sediments accumulate inside the water passages and block the water flow. This results in FILL SYSTEM and Open Tap errors. Please try to descale the machine 6 to 8 cycles. Let me know if that helps.
Hello. I tried to descale the machine with descaling solution and vinegar for more then two weeks, but it doesn't help. I still have the same problem. Any suggestion Parts Guru? Thank you. Andrew.
I just finished watching one of your video. I have a Jura Impressa E8 and i am getting an Error 8 message. Do you think i need a new Brew Group or it just needs a good cleaning? I have never taken it apart to clean it.
Hi Chrissy, The video should give you an idea whether to take on the brew group rebuilt project. I encourage you to also watch the brew group disassembly video. That video walks through the entire brew group disassembly process so you will know what it takes to rebuild the brew group or replace the entire unit. If you decide to rebuild, you will only need to purchase the tune up/rebuild kit.
Hi Dusty, This is a problem with one side of dispensing spout clogged with coffee or Calcium. Coffee after extraction from the brew group flows does the tube from brew group as gravity flow (no pressure from the pump. The passage of coffee from brew group to the cup needs cleaning. You need to fill water tank with descaling solution and use 3 or 4 rinse cycles. If you do not have Jura descaling tablets, you can order our descaler powder DSC-6. This is powder form that can be dissolved and filled in the tank.
Why don't you tell the guy what to do? Quick solution, use a paper clip to unclog the spout. Unfold the paper clip and poke the 4 openings in the spout clear.
Quick solution, use a paper clip to unclog the spout. Unfold the paper clip and poke the 4 openings in the spout clear. For a full solution, you need to take the machine apart, remove the spout and clean it. This is easily a 2 hour job for someone not familiar with this, so the paperclip solution is always fine unless you got pests (roach, etc.) stuck in there...
На мой взгляд здесь неправильная эксплотация, кофе сильной обжарки + регулятор помола на минимал, получается то, что видем и это правило как убить любую кофемашину.
![I.N "HALLUCINATION" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/n5B5q1Hwt_U/mqdefault.jpg)
![Jura zetgroep revisie [Nederlands gesproken]](/img/1.gif)
Thanks sooooo much for this. Just replaced my E8 brew group with your super instructions and it works perfectly again. I was stumped on how to get the thing to come apart. Cheers!!!
thank you for such a great range of videos, as a retailer of Jura in australia you give us better information than the company themselves. I would recommend your services to anyone.
Thank you very much. Your are very good at what you do. This time I have been able to open and clean the machine myself. I will order some parts from your company. You are the best!
You guys are the best on youtube when it comes to Jura. Thank you!
As the rest of the viewers. THANK YOU so much for putting these videos available. I just cleaned and refurbished my C65 brew group. However, now the brew group is noisier than before. Is there a tip in the reassembling and mounting that can reduce the noise. Once again, thank you so much for these great Jura training videos.
Hi, ensure that brew group vertical gear is properly seated into the teeth of the small white gear on the brew drive motor.
Thanks again for your support
Great video. Very happy to find this information. Can't wait to open up my Jura and work on that brew group!!
Благодаря этому видео мы с отцом починили свою кофемашину. Винты откручивал проскогубцами.
Thank you parts guru, great video. Now i can clean my machine properly. Well done :)
Thanks a lot
Can you make a vidéo on how to charge the switch that causes the missing basket message please ?
Thank you very much for sharing your knowledge, this video was very helpfull for me.
+Christian-Maurice Duval Glad to hear it. Hopefully you were able to fix your machine.
for Jura E50 I can't find anywhere what gasket is needed for steam valve connected to thermoblock? No picture no info, nowhere. I have there serious leaking hot water under pressure and can't find what is needed there, what type. Could you help me please?
Hello, old style gasket for E50 is no longer available
Thanks for your helpful video. I cleaned and reassembled the brew group on my E50 with your help. When I power it up it runs an initiation sequence and finishes with all flashing lights. Any assistance would be much appreciated.
+velotique Do you get hot wter when you operate the machine? Also, the brew group could be incorrectly installed resulting in flashing lights. Please re-do the installation and see if that helps.
+Parts Guru Thanks for your quick response. The brew group was miss-aligned. Fixed it. It would be useful to show how to align the brew group by running through the brew cycle. Thanks, I appreciate all your help.
+velotique I'm now getting water leaking out the bottom of the brew group when coffee is extracted. Water runs out of the drain valve when I switch to steam or water from steam wand. The water line connections to the drain valve is good. Is it the steam/brew solenoid valve or micro switch? Or is it the drain valve on the brew group? Thanks for your help.
I have a problem with a jura impressa e85 it spills most of the brewed coffee into the tray… can you help me?
Excellent demonstration! My Jura Impressa E9 leaks water at the frother side. The membrane regulator is rusted. How do I take it out to replace it with a new part? Thank you.
+937tubeyou Hello: here's the link to the video that demonstrates how to replace the Jura membrane regulator in Jura E9:
ruclips.net/video/tarVahYAR1k/видео.html
our machine needs to be shipped to you for cleaning and repair. toledo265@aol.com need address to ship
This is a a very clear and helpful video which has inspired me to try my hand at cleaning and refurbishing my unit. There is one problem in particular. The spouts appear to be partially blocked with reduced flow and backing up of the coffee so that it spills out between the two spouts. Is there any easy way to fix this problem without dismantling the entire machine? Thank you.
I just finished the refurbishing and cleaning of the brew group C3000 and the malfunction 8 error is now eliminated!! Many thanks for the tutorial it was a blessing to us. Now however, no water is reaching the rinse cycle or entering the grounds, do you have any suggestions. Thank you for the fast delivery of the o-ring sets. What a great service this is!
Great video. I have an F7 and the coffee is only coming out of one of the two spouts. How do I fix this? Thank you.
Hi. I gave it my best shot and took apart the machine, changed and oiled the oil rings and had all the right tools. Alas, when I turned it on my machine made an absolutely horrible sound and then returned to E8. I thought I had followed your directions carefully but I guess not. It's quite possible that I reversed an item while assembling the brew group. Whatever it was, I failed and the thought of disassembling again to find the problem seems overwhelming. It would have been great to have a reassembly video as opposed to watching the disassembly and thinking in reverse. Thanks anyway. :))
+Mary Christine Andrews Hi, the Jura brew group disassembly video is also posted, please click the link below to watch the Jura brew group reassembly video. Hope it helps:
ruclips.net/video/W1n7jT6_kEA/видео.html
Great video. I have an E8 machine like in the video. What is the best way to clean the grinder on this machine?
Hi, We have a Jura Grinder Burr replacement video posted on our RUclips channel. Please watch it to learn how to clean the grinder in Jura espresso machines.
Good evening,
I have a Jura E75 and from time to time the coffee ends up in the bottom tray under the coffee grounds. It does not flow from my 2 holes. What could I do. Thank you, Adrian
Which auto coffee maker do you thing is the best made?
Thanks for this view! I have a Ena Micro 1. Can I open it and clean it inside?
how different is the C9 from all those models you list as similar please?
C9 is similar internally as Impressa E8, E9. It has a solenoid valve located below the thermoblock to control steam/hot water flow from the cappuccino spout
@@PartsGuruUSA Thanks for that: Does that make accessing the brew head for cleaning any more difficult?
@DManzaluni It does not. Removing the brew unit is same as Impressa E8
Thank you for the video! Unfortunately I broke a piece off the when trying to get one of the side panels off the brew group. Do you know if it is possible to buy just this part? I glued it and put it back together without difficulty but am worried it is not going to hold.
Hi Cheryl:
Which side panel did you break, right or left? We should have a brew group side cover/panel for you.
Parts Guru
Hi, it is the left (water tank side) piece. I put everything back together after cleaning and lubricating as you showed (with the glued piece which appears to have held), but it does not work--the error 8 message still happens. I took the top back off and tried to see the problem--the large piston is going up and down as it should several times while machine says heating or rinsing but apparently it cannot progress from there. Not sure if I should take it apart again or look into replacing the whole brew group? Can you tell me the cost for this? Or should I just send it to you at this point?
Cheryl W
You may have missed a step during re-assembly. You should re-assembly it correctly by watching our brew group re-assembly video. Depending on how old the brew group is, you may want to replace it with a brand new one. Here is the link to purchase a brand new brew group:
www.shop.partsguru.com/Jura-Brew-Group-Impressa-C-E-F-S-Series-0010507.htm
We are here to help, should you have more questions.
Very informative video. The issue with my E8 is that the display is stuck at the "Empty Grounds" message. There are no grounds, and nothing I do seems to be able to get the machine to move beyond this message. Is there a sensor that may be stuck or need replacing? If so, where could I find it?
Eric Roman Used coffee grounds are collected in the used coffee container. If the display shows EMPTY GROUNDS, no more coffee can be made until you empty the used coffee container.
• Carefully lift and remove drawer since there is water in it.
The display shows DRAWER MISSING.
Important: Do not unplug the machine while you are emptying
the coffee grounds.
• Empty the used coffee container and the drawer.
• Push the drawer back into the machine. The display still shows DRAWER MISSING.
• Place the used coffee container on the tray and insert back
into the machine. The display shows READY and you may now continue brewing coffee.
Parts Guru Thanks for the reply. The problem I am having goes deeper than that, unfortunately. I have had the machine for almost a year and a half, and have emptied the grounds container many, many times, so I am familiar with the procedure you outlined. However, the machine is now stuck at the EMPTY GROUNDS message. When I remove the drawer, no DRAWER MISSING message appears. The display stays at EMPTY GROUNDS. There are no grounds to empty. So I was wondering . . . is there a sensor that might be clogged or need replacing?
Eric Roman Pull out the drip tray, and remove the used coffee container. Wait 10 seconds, reinsert the tray without the used coffee container. See if the message disappears. If it does, then pull out the tray again, wait 10 seconds, and replace the used coffee container and reinsert the tray.
Perform the above while the machine is on.
Hope the above helps!
Just trying to get an answer on the following question:
In order to get a fullsized cup of copy my E45 produces only about or less than 1 cm in a normal cup; this has happened since I had overcome the problem with the cleaning program.
What could be the cause of this failure? The electronics?
Hi, What kind of problem did you overcome during the cleaning cycle? Is the machine is stuck in cleaning mode?
(Answer took a while because of problems with pc)
I do not recall why after several efforts the cleaning program came to an end, but after that had happend the aforementioned problem occurred.
I you could give me a clou as to where I have to look (after opening etc the machine, I would have the need of the special tool and the appropriate service manual)
We are in the process of acquiring new ENA Micro machines. Once we have them, we will post a video on how to disassemble them. Stay tuned!
It looks like the impressa c60. Only the clips of the fluidhoses are different and the plug to the coffee outlet.
Is there a part 2???
Do you have a video on how to remove the top panel of an Ena 9 ?
I have seen your Jura E85 Brew group replacement. I have also a Jura E85 and I have a problem with the coffeemachine E85, because the coffee contains less beans, so the coffee tast to much watery. I think the coffeemill/grinder grinds to less beans. How can I repair this? There are enough beans in the machine.
Hi again
got a new pump in my jura impressa E40 and heats water, but the problem now is when I plug it into mains the water flows non stop in coffee brew and when I switch it over to steam/water nozzle water just flows all the time.
+Totlino Totolonio I think you have reconnected wires wrong to the pump or to magnet valve which is on the same circuit as the pump.
To check if pump is being powered by any shorted function in the machine, you should turn the machine off. Disconnect one wire on the pump to isolate the disconnected wire. Turn power to the machine on and see if the pump is still on.
If so, then the machine is grounded.
Tyred the wires again as you said,but still same problem. Only when I disconnect a wire then pump stops, but when I press button for coffee I have to put the wire back on so water flows then after coffee brewing is I have to disconnect the wire again or the water flow keeps on flowing.
+Totlino Totolonio okay, please email pictures of the wires connected to the pump. I think the wires are not connect properly
Is this grinder assembly compatible with an Jura ENA4?
trying to get the side panels back on the ENA3. They came off easily but not going back in place. Any suggestions?
Hi, You've done the difficult part i.e. removing side panels. The hooks on the side panels are locked into the slots at the top and bottom of the sides.
+Parts Guru Yes, we see it all and when we lock in all the parts, the panels won't move all the way forward so that the hole for the screws on top don't line up no matter how we push or try to move panels. Thanks again for your great video. I am going to post it on my blog, shelleysays.com.
Please ensure the two side panels locking tab in the front of the machine (below the coffee outlet) are pulled down. This allows the side panels to slide all the way to the front. The side panel would not snap in into the locks at the front.
+Parts Guru Will try this when the hubby comes home. Thanks!!!!!
+Shelley Garfinkel I just posted on my blog if you want to read it and comment. I can always edit: www.shelleysays.com/2015/12/super-automatic-coffee-machines-are-not.html
So which newer machines would you recommend?
Hi , thank you for your usefull and proffesional pesentation . My problem with my jura c5 is that when i start making my coffee i press the boton and water goes into the tray instead of coffee cup . Then i press the water cleaning boton and no water poors . I repet the water push boton and after 4-5 times water starts . And then i can try to make coffe again and maybe coffee is coming to the cup . If not , no water is coming , the coffee grind is dry in the beem and more water is in the tray . And i start again by trayng to rinse . What is the cause of this ?
Thanks for the Video, just have a question regarding the Jura grinder and wondered if you might know the answer. After accidently putting wet beans in the grinder and trying to make a coffee, I took the grinder apart using your video, cleaned out the caked coffee and put it all back with exception of one very small bearing and spring. (So in total mine had 4 springs and 4 bearings)The other 3 bearings and springs were larger and obvious where they needed to go but I reassembled the unit and all seems to work for 5 coffees now. Any ideas where this would go or for what purpose it serves ?
Hi, I am trying to unscrew the T20 screws to release the Brew Group on Jura C50 but with no success they just would not budge, please help!!!
Teal'c Herman Hi, Are you able to firmly seat the torx screw driver into the screw itself? Try T25 and see if that helps with the firmer grip. Avoid stripping the screw.
Parts Guru Thank you very much for your reply, "I called a friend" who is stronger than me, he managed to unscrew them, it turned out both screws were glued in. Your videos are perfect, I managed to open the machine clean it, disassemble the Brew Group clean it lubricate it and reassemble it, put everything back together and try it unfortunately it still doesn't work and the message that keeps flashing is "switch open" any idea what that means please?
Kahve makinemin atik kahve kismindaki kahveler yuvarlak cikmiyor, sıkıştırılmamış sekilde daginik cikiyor neden olabilir
What do you think is wrong, when in a Z5 " System fill " came out and nothing happen when I push the Rinse button.Thanks
Still best brew unit
in my Jura E70, coffee does not come out of the spout, noticed the water does not get mix with coffee, coffee grounds go in the container below and water goes in to the tray, the magnet at the bottom of the brew group and the cubical unit does get pulled in like it suppose to, all lines appear to be open, what else can be checked in the coffee machine to fix this problem, appreciate any help.
Ebbie Attar Check the fineness of the used coffee. Is it too fine like flour or table salt grain? Perhaps the grinder burrs need to be replaced. They are likely to be blunted and do not grind enough coffee.
Hi Parts Guru I have a Jura Impressa s9 with the new style jura fine foam frother fitted, When just making a normal coffee, the Frother has started to leak out water at the same time, any ideas please
The new frothed is probably not installed properly.
Hi Guru. I have S9 and this morning it stops producing coffee and espresso. screen said brewing and then enjoy like normal, but nothing coming the machine. any idea?
Hello Sasha,
The machine could use TLC. How long have you owned it? You can ship to us for repairs. We are based in near Philadelphia, PA.
Hello Parts Guru...Great stuff thanks! I seem to be having trouble with my C9. We use it about 10 times a day to make cappuccinos and have noticed lately that the automatic frother has been having trouble continuing to make froth for the entire 20 seconds. for the first while it is fine and then starts to just spit steam and there is barely any milk entering the system. I have checked the seals on the milk container all the way to the machine and they seem fine. Pump replacement? cleaning? any suggestions? thanks
Hello Kolin, Please clean the cappuccino system thoroughly using the Jura cappuccino cleaner. Is this the only issue you are experiencing? Descaling the machine thoroughly should help as well.
I keep getting the Error8 message all the time on my E8 Jura. If I wait overnight, the machine usually fixes itself, but it happens daily. Great video. Can you tell me materials I need to try to fix it myself? It's soooo expensive to send it out for repair that I am ready to take the plunge and give it a go with your video support. Thanks!
Hi: Its time to rebuild the brew group. 90% of the times, Error 8 results from malfunctioning brew group due to worn out piston seals and o-rings.
We sell a complete brew group tune up kit inckuding the oval head tool that you can purchase by clicking the link below:
shop.partsguru.com/Jura-Brew-Group-Maintenance-Kit-0010729.htm
Also, we have posted a RUclips video that demonstrates how to disassemble and reassemble the brew group.
We're here to help, should you have more questions.
Great video. Since I have the E8 and will keep it. I can make sure it is super clean. How often should one clean the inside of their machine? Is there a recommendation for every 6 months or ?? I am going to replace those oval screws with Torx screws.
Hi,
my Jura F7 only has one working spout. The left one doesn't work. I think it's blocked. Do you have any suggestions?
Thank you!
I called in with this problem and one of the techs had me go through the cleaning cycle and use a toothpick to clear out both spouts, while the water is rinsing through, slide the adjustable spouts up and down to flush any clogs out. it worked for me. A big glob came out the clogged side. I periodically slide it up and down during the cleaning cycle while there is liquid coming through now.
Hello, I have a Jura impressa J6. I waited for 1 week to get the tool for my machine. The computer comes on and says that I should fill the beans. I know that there is probably oil and beans in the grinder. We finally received the tool to twist the grinder but it jumbles the beans still are not going into the grinder. Our Jura is 1 year old and so I know that we should open it up and do something. I don't want to send it to Jura. This is too frustrating!!!! Please can you help. Should my husband open it up and remove the grinder? I don't know. Please reply...
I'm interested in the ENA Micro also. Thanks!
Hi there. My Jura S9 is giving problems with the milk Frothing and heating. It seams like the steam pressure is too low to develop a stream of milk flowing. We've tried to do a cuppachino cleaning or descaling, but not enough pressure to even suck the solution through the throth-ing device. The rotatory switch don't want to adjust the amount/duration of water flow. Any suggestion on what the problem might be?
I followed this and successfully removed the Brew Group from my E80, gave it a good clean and put it back. However, now when I turn the machine on, the motor runs moving the brew group up the screw to the top and then the motor continues making a horrible grinding noise. When I looked closely, the long cylindrical cog that is removed with the brew group is not turning, but the cog that drives this is.
I tried to manually wind the brew group back down to the bottom and try again, but the same result - it moves all the way to the top and then tries to carry on going!
Any ideas on what to do? Does the motor stop when it CANNOT turn any more, so the issue is that the brew group isn't quite in place so there's a little "give" allowing the small cog to keep turning, albeit noisily. Or is there some kind of sensor that alerts the machine when the brew group is in position that is failing, so the motor continues turning?
Hey Tony would you mind sharing the details on how did you solve this problem? thanks got the same behavior on mine.
@@enriqueyescascruz9907 Of course, I'll try.
For starters the grinding noise was because when the brewgroup reached the top, it could go no further, but because the motor didn't stop, it broke the plastic around one of the two screws on the other side (they hold the motor against the tall metal cylinder that drives the brewgroup up and down). Before I could do anything else, I needed to fix this. You may have the same issue. I used a combination of superglue and araldite to cement it back together.
As far as the brewgroup itself went, I removed it again and followed this video: ruclips.net/video/W1n7jT6_kEA/видео.html and this time made sure it was in "home position" before reinstalling it.
This time when I turned the machine on, it worked perfectly.
I hope you have the same success!
quick question. The grinder in my jura machine gets backed up in the grinder(square channel). took the whole grinder pieces and cleaned really good and made sure its dry(not greasy). first brew, thru the grind far out, second brew got backed up in the square channel again.
what can cause that?
Thank you
Hi, great video, thank you. I was getting error 8 on my C9, I was able to disassemble clean and reassemble the machine, thanks to your videos. But I still have an issue. The machine still makes coffee, but there is a very loud noise from the motor after the coffee is poured and when it ejects the coffee ground it has not been compacted and is still loose. Any help would be appreciated.
Hi Stephen,
Please ensure that small white gear on the motor is properly seated in the vertical guide. Check that brew group motor is properly fastened and should not wiggle.
Parts Guru hi, thank you for your response. Everything is seated perfectly and when the brew group is out it moves freely. I have even fitted a new encoder, still the same.
Hi Stephen,
Can you isolate pop sound while the brew group is returning to home position? Could it be coming from inside the brew group?
As for the loose coffee grounds in the container, I suggest you adjust the grinder setting to coarser. Make three coffee for the new setting to take effect.
Let me know if that helps.
By the way, how many cups of coffee have you made on this machine? When was the last time you cleaned the grinder chamber and replace the conical grinder burrs?
Parts Guru thank you so much for your advice, I stripped the brew group down and I had missed some hardened coffee pieces. So now it makes coffee perfectly, unfortunately I now have another issue. When it rinses no water comes through, I’ve checked all the connections and the water comes through when making coffee just not when rinsing.
Hi Parts Guru, my Magimix R500 is just like this machine. When you try brewing the coffee, the sound coming from the pump begins to fade out and trhe whole proccess stops. Is it possible there is a blockeage in the inlet to the brewing unit? It doesn't have the problem while pumping hot water.
Cheers-Jorge
Hello Jorge, what happens when you run the hot water cycle? Do you get steady stream of hot water?
You also want to check the fineness of the ground coffee beans. If the ground beans are too fine like flour then you need to adjust it to coarser setting like table salt grain.
Please feel the fineness between your fingers. Adjust it each notch towards coarser setting. Make three espresso's for the grinder setting to take effect. It's important to adjust the grinder while the grinder is engaged.
Hope the above helps!
Sorry just noticed your msg! Hot water. Bee unable to make any coffee at all, as the machine stops like the pumps loses power???
Hey parts Guru, it feels like there's a loss of pressure, as I can hear a hissing noise
possibly coming from the brewing unit?
Hi I have Jura impressa 50
I took out a coffee ground tray to empty and now it will not go all the way back in.
Can you help? thank you
Aggie Maiorano Operate the machine without the used coffee grounds tray. Allow the brew group to reset. Re-insert the tray. It should fix the issue.
I would like to order the oval head screw key. How do I do that?
Loretta Castleberry The link to purchase the oval head key is in the description of this video
Please, can you help me with my Jura Impressa e8? It is asking to fill beans when it has beans inside already. Because of that, it doesn't make coffee. What should I look for here as a problem?
Hi Patricia, Did this issue suddenly start? Were you able to make coffee using the grinder? How long have you had this machine? And, when was the last time it was serviced?
I just finished installing the Jura brew group because I had an error 8 message. When I was done I went to use it and now it reads filling system and open tap and I can not make it do anything different. Can you tell me what I could have done wrong.
+Tanya Reis Hi, are you able to use hot water side?
Did you disconnect any water tube connections other than the one going to the brew group?
Does the pump operate when you select hot water or steam?
Please help me : my Jura C5 is making expresso occasionally : water is drained through the drainage valve and not going through the Brewer unit. Is the same when trying to drain ; drains through the drainage valve and does not go to the coffe cup. This happens 80% of time.... I guess is the driange valve which is occasionally leaking ?
Hi Marc, The drainage valve has a white cap that is pressed against the magnet valve needle. The cap is attached to the stem of the spring loaded metal shaft that, when pressed, allows the hot water from the thermoblock into the brew group. Please ensure the drainage valve is properly aligned with the needle on the magnet valve.
I dismantled the drainage valve (ordered the gaskets), put some silicone paste, but still occasionally the drainage valve does not close. When removing the electro valve and acting manually with a screw driver works fine. Looks like to be the electro valve failing, but really strange, maybe still pushing a little sometimes on the white cap. really confusing.
Do you do manual cleaning and what is charge? Jura E8
Yes, we repair the E8. We rebuild the brew group, properly and thoroughly descale the machine and replace the broken parts. Are you located in USA?
Hello. When i activate my Impressa E60 machine no water or coffe comes out of the coffee spout. The machine makes normal sounds but the water and coffee ends up in the container and drip tray. What can be the problem here.
Error code 8. What can I do?
Great stuff. However I opened it. and it does operate the brew system, but it makes a lot of noise, so maybe it needs calibration? And then it keeps showing No beans all the time. How does the machine know there are no beans? Where is the detector located? I plan to use it with coffee powder so don't care about beans.
+Peter Vekinis Hi, please rebuild the brew group while you have it opened. Replace the brew group piston o-rings and properly lubricate it with food grade lube. The brew group rebuild video is also posted on our channel.
The grinder burrs are probably blunted so it doesn't grind coffee beans. You should consider replacing the grinder burrs to start using the freshly ground beans. Try our 50 50 Buzz espresso beans blend. I think you'll like it. Sample is available for free with purchase of parts.
Hello Parts Guru. I have a Jura Impressa E9. A few days ago my machine ceased to work. When I switch on the on the display appears the inscription "Open Top" when I'll do it on the display appears the inscription "Filling System", the machine makes a lot of noise and nothing happens. After about 30 seconds the display appears the inscription "Shut Top". Can anyone help me solve my problem. Thanks
+Andrew Piet Hello, the Open Tap issue is related to the steam valve that's mounted above the boiler and right behind the hot water/steam knob. The cause of malfunctioning is lack of Descaling the machine. If you're using Clearyl filter cartridges, please stop doing so. It's a waste of money. The Clearyl filter removes bad tasting elements from water; it doesn't remove calcium. When the machine is not descaled properly then calcium sediments accumulate inside the water passages and block the water flow. This results in FILL SYSTEM and Open Tap errors.
Please try to descale the machine 6 to 8 cycles. Let me know if that helps.
Thank you for help. I'll try to do that, but I have to buy this tablets. I'll let you know.
Hello. I tried to descale the machine with descaling solution and vinegar for more then two weeks, but it doesn't help. I still have the same problem. Any suggestion Parts Guru? Thank you. Andrew.
I just finished watching one of your video. I have a Jura Impressa E8 and i am getting an Error 8 message. Do you think i need a new Brew Group or it just needs a good cleaning? I have never taken it apart to clean it.
Hi Chrissy, The video should give you an idea whether to take on the brew group rebuilt project. I encourage you to also watch the brew group disassembly video. That video walks through the entire brew group disassembly process so you will know what it takes to rebuild the brew group or replace the entire unit. If you decide to rebuild, you will only need to purchase the tune up/rebuild kit.
hi
I error 1 error and 5 ??
I just change the whole boiler is ok except the error
what should I do ?
Thank you
Pierre
Replaced the temperature/omega sensor.
I'm only getting coffee out of one of the heads , not both. Any assistance ?????
when I press 2 cups only coffee comes out one of the openings. Any suggestions for my Jura e9 ?
Hi Dusty,
This is a problem with one side of dispensing spout clogged with coffee or Calcium. Coffee after extraction from the brew group flows does the tube from brew group as gravity flow (no pressure from the pump.
The passage of coffee from brew group to the cup needs cleaning.
You need to fill water tank with descaling solution and use 3 or 4 rinse cycles.
If you do not have Jura descaling tablets, you can order our descaler powder DSC-6.
This is powder form that can be dissolved and filled in the tank.
Why don't you tell the guy what to do? Quick solution, use a paper clip to unclog the spout. Unfold the paper clip and poke the 4 openings in the spout clear.
Quick solution, use a paper clip to unclog the spout. Unfold the paper clip and poke the 4 openings in the spout clear. For a full solution, you need to take the machine apart, remove the spout and clean it. This is easily a 2 hour job for someone not familiar with this, so the paperclip solution is always fine unless you got pests (roach, etc.) stuck in there...
Peter Nielsen he did and verry clear,and your methode Will not clean.. @partsguru Nice job sir
belissimo, grazie!!
Forgot to mention , I have Jura Impressa e9
Hi did you see the picture
No water out of either side. Just a small amount.
👍
We does anyone buy such an expensive machine that can´t be cleaned easily? I never understood that.
Excellent explanation for a truly horribly designed machine.
На мой взгляд здесь неправильная эксплотация, кофе сильной обжарки + регулятор помола на минимал, получается то, что видем и это правило как убить любую кофемашину.
Caution first:Before any work on the espresso machine, disconnect it from mains voltage!!!!!
Darum keine Jura
What's your address or your phone number thank you