Good job putting some loose blocks in the hole. But, why skimp on the base plates for the bridge? Could make them bigger or same size as the bridge legs.
Excellent idea. Euro cars are impossible to jack up and put a jack stand, simultaneously. I also want to know what is name of the first music track that's being played?
Until last year, I had at least 6 cars in the house hold! All of them European cars (and van). I've got several jacks and jack stands, ramps, etc. I can assure, I NEVER worked on a raised vehicle without a jack stand... Impossible!! I don't think so. LOL 😂
Hello very nice ramp! Is there any reason why you didn't add a ramp to the back wheels just like the front so that you do not need to use a hydraulic jack to jack up the rear? Also do you think 2x9 is strong enough to hold a much larger car about 5000 pounds? Do you think its necessary to reinforce 2x9 with some type of metal bar? Thank you
I watched your video again and I think the reason for not using the ramp for the rear is because it will not clear the car. maybe perhaps is you remove the wheel stop, it just might fit? since you have the stop at front, you do not need a stop for the rear? anyways I like your video a lot and I learned a lot. Thank you.
Hello, I really like this type of ramp and stand. If I were to make these a bit wider at the base (bottom) do you think it would be safe to go higher to say 14-15 inches high? Thank you.
Maybe I'm a bit slow today. How did you get the rear wheels get up on the rear stands? There's nothing shown in the video and nothing at your website. Yet, I don't seen anyone else asking about that.
CAUTION ⚠ - DO NOT LIFT AN UNLOCKED WHEEL, like that! Simple and basic physics, the wheel will roll. As consequence the entire assembly can and will fall! With luck only the underbody of the vehicle will be damaged... And yes, don't ask! ;-)
it would be better if you narrated the process instead of just showing a pile of cut wood blocks with music, we can get music anywhere but the information would have been nice.
Хобби
the best car ramp on youtube
Thank you..
best design I've seen on youtube
thanks for the comment
GOOD OLD AMERICAN KNOW HOW even if your not an American thanks for posting
Clever and useful. Thanks!
Thank You for your comment..
Muito legau e criativo, ótima idéia
obrigado pelo comentário
Nice orange break drum
Good concept. Thankyou. Regards Stephen
Thanks for watching..
Nice job. Greetings from Athlone!
thanks for the comment
thanks for the comment
Can modify design for size of jack. Love the idea
0:55 I would add a strong metal handle on the side of the ramp to make sliding it out, after the car is on the platform, easier.
will do..thank you for the comments..
Great design! Could you please list the dimensions in the description?
you can visit www.jlsetnuper.epizy.com
I like this, along with your other videos. I would like them a lot more if you got rid of the music and replaced it with some narration.
Thank You..
멋지네요
감사합니다
Good job putting some loose blocks in the hole. But, why skimp on the base plates for the bridge? Could make them bigger or same size as the bridge legs.
Yes, I place wider blocks when I go higher..thank for the comments..
很巧妙的设计 well-designed
Thank you
Excellent idea. Euro cars are impossible to jack up and put a jack stand, simultaneously. I also want to know what is name of the first music track that's being played?
thanks for the comment...music track "lonesome avenue the 126ers"
Until last year, I had at least 6 cars in the house hold! All of them European cars (and van). I've got several jacks and jack stands, ramps, etc. I can assure, I NEVER worked on a raised vehicle without a jack stand... Impossible!! I don't think so. LOL 😂
Genius!!!
thanks for the comment
Hello very nice ramp! Is there any reason why you didn't add a ramp to the back wheels just like the front so that you do not need to use a hydraulic jack to jack up the rear?
Also do you think 2x9 is strong enough to hold a much larger car about 5000 pounds? Do you think its necessary to reinforce 2x9 with some type of metal bar? Thank you
I watched your video again and I think the reason for not using the ramp for the rear is because it will not clear the car. maybe perhaps is you remove the wheel stop, it just might fit? since you have the stop at front, you do not need a stop for the rear? anyways I like your video a lot and I learned a lot. Thank you.
@@Sungjuleeyes yes I cannot use a ramp on the back, car is too close to the ground at the back..
yes you can use 2X9, but it should be a solid design.
@@jlsetnuper thank you very much for your reply.
good job.
Thank you
Hello, I really like this type of ramp and stand. If I were to make these a bit wider at the base (bottom) do you think it would be safe to go higher to say 14-15 inches high? Thank you.
Yes , it is safe to work with this ramp, I already tried 16 inch high, as long as the base is solid and wider..thank you
JLS Etnuper thank you very much for the reply. It’s much appreciated.
JLS Etnuper , thank you for the information, its much appreciated.
JLS Etnuper I’m going to download the plans from your website. Thanks again. Howard.
@@howardlee7216 thank you
Clever!
thank you....pls subscribe
nice idea
thank you..
Maybe I'm a bit slow today. How did you get the rear wheels get up on the rear stands? There's nothing shown in the video and nothing at your website. Yet, I don't seen anyone else asking about that.
ruclips.net/video/kDCy6WYn3eU/видео.html
This page cannot be opened, it says that the website is having technical problems.
So, what happened to the plans ??? I go to your site and see nothing ?
The site is down?
Hello, I purchased the plans from your website and I wanted to ask how I download them. Thank you.
when you finish the purchase and click to back to merchant , you should be directed to download site media fire
if you cannot download ..i will send it to your email and print it
pls check your email
JLS Etnuper , Thank you, I got them downloaded. Looking forward to the building of it.
CAUTION ⚠ - DO NOT LIFT AN UNLOCKED WHEEL, like that! Simple and basic physics, the wheel will roll. As consequence the entire assembly can and will fall! With luck only the underbody of the vehicle will be damaged... And yes, don't ask! ;-)
Before lifting..make sure the hand brake or emergency brake is engaged..and it did not roll eversince..thanks for watching..
hi i purchased the plans but after i have downloaded them i get an error when i open the pdf file .
may I have your email address, I will send you another copy of the plan..thanks
Still not working.
I informed him with a comment in his last video. Hopefully he will fix it.
hi ok ive checked my email but nothing showing
open the attachement of the your email
How hard is it to make a video in stead of pictures? Still a nice design
next time we make a video..thanks for the comment
jozef danyi - Please feel free to do it anytime... ;-)
hi I've emailed you directly with details .thanks
i need your email where I can send you the copy of pdf plan..not in youtube comment..thanks
it would be better if you narrated the process instead of just showing a pile of cut wood blocks with music, we can get music anywhere but the information would have been nice.
sorry..maybe next time..
ok ive resent it im with outlook
check your outlook email..
yea i have sent it to your personal email
I did not receive your email on my personal email..do you have a gmail , or yahoo or hotmail?