Does the green/white wire go to ground inside the CDI ?. In the Honda CT110 Postie wiring diagram there is no green/white, a very short wire from the trigger to ground. I want to use the old Honda CDI.
@@garageadz Sorry, not sure I follow. Some of these engines have a series of gears that bypasses the transmission and allows them to start with the clutch disengaged (so they'll start in gear with the clutch pulled), on others the kickstart turns the gearbox which turns the crank via the clutch (so they need to be in neutral with the clutch lever out in order to kickstart). Just wondering if this engine will kickstart with the clutch lever pulled? DHZ didn't seem too sure...
@fhtyyn yep sorry, to be clear the clutch lever will have a switch on it that disables the starter function. If you don't wire that or don't have the switch, you will be able to start it if in gear or not. I hope this is clearer.
Built my custom gpx mini motocross o it bike with $1000marzocchi forks and flat side oko race carby heavy duty red rims bunch off other stuff list goes on and it's a beast got the bike cheap for $200 stripped it down cleaned it up put the new motor in it and all the new parts worth 1500
possibly, depends what CDI you're using and what the engine is setup to work with. I've done a few mixed with random parts. As long as the casing and signals match the CDI it's usually not an issue.
It's a 8 pin cdi. Uses 7 wires. 12v 12v switch Ground Ground Trigger - Trigger + Ignition to coil Its a 2001 kawasaki prairie 300. But I want to see what the pin out is on the ebay dc cdi because my oem is $200 used and like $600 new
Thanks mate! Im a sparkey who has bought a non runner project and you have helped me out! LEGEND 😊
Just earned yourself a subscriber. I got my son's apollo RFZ engine swapped for a ytx 150 and I got it firing 🔥 thanks to this vid.
Thanks mate, glad I could have helped :)
Thanks for the video about Hungary!
Best video ever mate . You helped me out so much with getting my gpx125 going .👍
Thanks mate I appreciate the feedback :)
Dude you are a legend. Really helped alot, appreciate your time and effort
All good, hope it helps! This stuff isn't really well supported so I'm just happy it's helping others.
Thank you sir your video helped me when i couldnt find shit for info any where else
Welcome to the GPX community, mate.
Thanks, you are a life saver.
ありがとうございます。私のGPX125に付属されてきたCDIの結線の方法が理解出来ました。
おかげで私はそれが助けてくれてうれしいです
Thank u soo much u dont even know that this video is gold to me .thank u for such a great video .
Glad I could help
Does the green/white wire go to ground inside the CDI ?. In the Honda CT110 Postie wiring diagram there is no green/white, a very short wire from the trigger to ground. I want to use the old Honda CDI.
I have the same cdi and wires from engine but my engine doesnt have the red/white wire. What should i do?
does that have rev limiter? and how does it work
Yeah it's got a limiter, cuts ignition.
@@garageadz what pin in the cdi is the limiter becuase mine doesnt seem to have rev limiter?
There's no pin for it, it's done internally of the ecu
@@garageadz okay, thanks
Hey how are you? I would really like to have the wiring diagram. Thank you..
Can you connect an electronic tacho to this plug to get a trigger feed? Which pin?
Does this 8 pin CDI work with a bike that doesn’t run a battery?
Yep it sure does.
Hey, does this engine start in gear or does it need to be in neutral with the clutch out? Cheers
If you wire it up, you can make it start in gear if you want
@@garageadz Sorry, not sure I follow. Some of these engines have a series of gears that bypasses the transmission and allows them to start with the clutch disengaged (so they'll start in gear with the clutch pulled), on others the kickstart turns the gearbox which turns the crank via the clutch (so they need to be in neutral with the clutch lever out in order to kickstart). Just wondering if this engine will kickstart with the clutch lever pulled? DHZ didn't seem too sure...
@fhtyyn yep sorry, to be clear the clutch lever will have a switch on it that disables the starter function. If you don't wire that or don't have the switch, you will be able to start it if in gear or not. I hope this is clearer.
Built my custom gpx mini motocross o it bike with $1000marzocchi forks and flat side oko race carby heavy duty red rims bunch off other stuff list goes on and it's a beast got the bike cheap for $200 stripped it down cleaned it up put the new motor in it and all the new parts worth 1500
I have a megelli 250 r wich uses an 8 pin cdi but the pinout seams to be deferent you think you can maby help me ?
If you want to shoot me an email to adsport@westnet.com.au I'll see if I can help you out mate.
I have the wiring diagram
@garageadz can I get a copy of you’re diagram please
Can I get picture of loom sent thanks
Legend
Bro I got a 8 pin and a 5pin can I use this harness to bypass the 5pin it's a 150cc Logan engine
possibly, depends what CDI you're using and what the engine is setup to work with. I've done a few mixed with random parts. As long as the casing and signals match the CDI it's usually not an issue.
thanks..
😀😀
Thanx!
Do you have one for a dc cdi?
Ah no sorry, I think I do have some half decent wiring diagrams that I've found though. I'll have a look and report back, see if I can help out.
Is your CDI 5 or 6 wire?
It's a 8 pin cdi. Uses 7 wires.
12v
12v switch
Ground
Ground
Trigger -
Trigger +
Ignition to coil
Its a 2001 kawasaki prairie 300. But I want to see what the pin out is on the ebay dc cdi because my oem is $200 used and like $600 new
Do you think you can send me that file? And thanks for the video
I can mate, what's your email address?
Hi can I please get the image
Hi what's your email?
@@garageadz dmanthegreat22@gmail.com
@@garageadz can I get a copy of you’re diagram please
@@nikjackson8 what's your email address?
@@garageadz nikjackson8@googlemail.com
Built a gpx mini chopper that was a weapon and is on RUclips but not very good footage
I went to your channel and checked it out, looks cool! What size flat slide did you go for and what jets did you use? I went for a 24mm OKO
hi could you send wireing digram for longshen z155 cdi unit.thanks keith
Hi sorry for the delay. What's your email address?