I don't know how much max apmere it supports , But I'm success with It. Thank You. I just tested under 2Amp, 12Volt and it's Okay. *I did not found D1047 Transistor, So I used 2 NPN transistor TIP122 in parallel and it works. Thank you again.*
Yes, I made it on bread board for test. Yes It works very nice. I used a 2k variable resistor on the place of 220 ohm so that the highest volt is under control when it is more than 24v input. And I used 1n5408 power rectifier diode for bridge rectifier. And tip35c transistor for power transistor. Coz it's wattage is more. Great project sir, thnx.
Salam dear, Sir, i need a variable power circuit (adjustable) with following specs. Voltage: 0-40 (Adjustable Ampere: 0.5-70 (Adjustable Battery charge controller relay (auto cut off) kindly update about charges? Contact details: mmchecnec@gmail.com Regards.
Sir multivibrator ckt mei capacitor ke negative pin npn transistor ke base se laga hota hai aur yeh Kaise kaam karta hai.ispar detail vdo banakar samjhaiye.
@@chargedlabs3506 well D1047 transistor is rated for 12 amps. You could easily use it for upto 8 amps with appropriate heat sink. Just don't forget that it's a linear regulator. So bigger heat sink is required.
It was great! I was interested in your style of your showing the schematic diagram ! althou i underestsnd nothing your languageAnd i did enjoy the music during playing.! Good luck.
Yeh ma nai phli video dekhi apki itna achi lgi k foran subscribe kr lya Bhai apny yeh nhi btaya k iska input AC hy ya phr DC wesay mjhy jahan tak lga Dc hy lekin agr kisi dc adapter pr lgaya to un k apny ampere hotay hain hm output pr amp adjust kesay karen gy isay input Ac to Dc bnain plz its a request... Main wait karun ga...🙂
Bro So far I have seen videos on Circuit making. But your way of presentation is very comprehensive. It is very easy to understand the Electronic Circuits better for nubees. Keep up the good work.
Ok sit koi baat nhi... Mujhe bs apka support chahiye.. Taki mein bhi kuch sikh sku.. College wale to kuch btaye nhi sirf 3 saal pr certificate thmaa diya... Ab jb mein kuch krna chahta hu to koi support nhi milta.. Kher thank u for rply..
Sir, i am so impress ,just want to know little think, if you can reply, What is the power factor or efficiency of this circuit? And how much max amp can be use from this circuit? And if u can add digital display then so nice of this circuity.
hi body .i can't undestand how do you conect the green line out of bd139 to 10k potentiometer pin 1 .is it conect to this pin? or it just go to base line of D1047?
sir can manage dc current by this divice when dc motor output is getting up to 1000 volt but we need only 60 volt dc motor and how to see output ampere of dc motor when we torque to motor sir please reply
Oye bro..! Al conectar dos Transistores D1047 en paralelo debo conectar una resistencia de 4.7 ohms 10w en cada patilla de salida de cada transistor..? O solo basta con una resistencia para los dos d1047..? Gracias..!
WHAT TYPE OF TRANSISTOR YOU USE NPN OR PNP BD139 ALSO I WANT TO CONNECT 5AMP TRANSFORMER FOR THAT WHAT I DO >5 AMP IS VERY GOOD FOR THAT BECAUSE WE CAN CONTROL CURRENT AS WELL >PLEASE ,MUST REPLAY AND if we connect 4 lm317 in parallel then it can draw 5 to 6amp as well but the transistor use for current thats the problem >if i know that transistor type then its easy for me to find equivalent> thanks you ! also very nice video >there are many types of videos are in youtube but the current limit function is 1 or 2 videos > thanks again KEEP UP
Hello bro I made this circuit it was well running but d1047 transistor got heated up very soon Today I used my micro motor and it got burned with fumes Please help me what to do Bhai And how will I check my transformer amp
@@armancodeq3642 Possibly if the specs are similar to the D1047. Most circuits use two or more 2N3055 in parallel but it wouldn't hurt to try the 2N3773.
i have implemented your circuit and its almost working but i m facing little problem that current voltage is regulating with same potentiometer means that voltage control potentiometer is also controlling current while current potentiometer is not controlling current. wht could be the reason of it...reply me soon... i got max 2.2 amp....
I don't know how much max apmere it supports , But I'm success with It. Thank You. I just tested under 2Amp, 12Volt and it's Okay.
*I did not found D1047 Transistor, So I used 2 NPN transistor TIP122 in parallel and it works. Thank you again.*
Yes, I made it on bread board for test. Yes It works very nice. I used a 2k variable resistor on the place of 220 ohm so that the highest volt is under control when it is more than 24v input. And I used 1n5408 power rectifier diode for bridge rectifier. And tip35c transistor for power transistor. Coz it's wattage is more. Great project sir, thnx.
Hey
Components k liye site batao
Jaha se buy kr ske
Salam dear,
Sir, i need a variable power circuit (adjustable) with following specs.
Voltage: 0-40 (Adjustable
Ampere: 0.5-70 (Adjustable
Battery charge controller relay (auto cut off)
kindly update about charges?
Contact details: mmchecnec@gmail.com
Regards.
@@prakashchandra9097
Electronicscomp.com
aap diagram or video bhahut jordar Explain hai . very Nice explain Diagram and video
Tq sir , I am from Malaysia.
very nice bro .samjhanay ka tariqa bahut acha hy
Valeu amigo! precisava de um projeto de uma fonte simples e funcional e esse seu projeto caiu como uma luva.
very best power supply and it is complete power supply for marketting
Very high quality circuit.Thanks .
Perfect tutorial video with proper explanation
Very Good...!!!
Sir,
Very nice.
बहुत अच्छा है भाई...धन्यवाद।
ईस डिवाइस से कितने "Amp"और कितने "Volts" तक की बैंटरी चाजॅ करसकते है...???
Ripley plz....???✒Ⓜ
You should have given a minimum of 5mm clearance off the veroboard with that 10 watt resistor... A very good presentation... WELL DONE!!! 9/10
I have made it ..it is working
Thanx sir
What is the input for this cicuit
Input voltage..
@@mohamedibrahimm3627 12 volt ac
Sir multivibrator ckt mei capacitor ke negative pin npn transistor ke base se laga hota hai aur yeh Kaise kaam karta hai.ispar detail vdo banakar samjhaiye.
Aapka samjhane Ka tariqa bohat achha he.thank you.
Very good video
प्रस्तुतिकर्ण बहुत श्रेष्ट है ☝
Bhai apne bohot Acchi tarhe ye samjhaya Or koi ase nahi samjhata very good
Amazing. I try this. And its working good. Thank you brother.
Pls tell me what is the input voltage
@@shafikahmed6889 for input im use trasformer 24v
and input Current ?
@@AGhosh-sb8lf 3 a
Input me saplai konsi ac 220 he ya koi transferred ko saplai he
When I saw the video I almost did not skip it. Now that I've made it, I adore him. Congratulations!
What is the input voltage?
What is the max current it can output
@@chargedlabs3506 well D1047 transistor is rated for 12 amps. You could easily use it for upto 8 amps with appropriate heat sink. Just don't forget that it's a linear regulator. So bigger heat sink is required.
تسلم اخي اسلوب رائع ومفيد جدا
You are great
Excelente 👍👍👍 buen trabajo muchas gracias
Sir thanks for reply this vedio is too good on you tube i can't find this type of vedio you explain perfectly thanks fou this vedio
Video*
Great explaination with diagram superb that's the plus point of videos sir
It was great!
I was interested in your style of your showing the schematic diagram ! althou i underestsnd nothing your languageAnd i did enjoy the music during playing.!
Good luck.
very nice
Compact design.A schematic would be helpful.Also, the audio score volume can be reduced. Thanks for sharing.
Excellent job...I am from Jordan , your efforts highly respected
beautiful circuit
Congratulations for the video...it's Very good
Superb !
nice video
Very helpful project bro.. Amazing
Gostei do vídeos deixei um joinha
Yeh ma nai phli video dekhi apki itna achi lgi k foran subscribe kr lya Bhai apny yeh nhi btaya k iska input AC hy ya phr DC wesay mjhy jahan tak lga Dc hy lekin agr kisi dc adapter pr lgaya to un k apny ampere hotay hain hm output pr amp adjust kesay karen gy isay input Ac to Dc bnain plz its a request...
Main wait karun ga...🙂
Good project
Bro So far I have seen videos on Circuit making. But your way of presentation is very comprehensive. It is very easy to understand the Electronic Circuits better for nubees. Keep up the good work.
Very good and simple to make
Very nice sir
thanks ❗❗❗
excelente
Nicely. its just voltage and current control only
Bro circuit diagram is best
Ok sit koi baat nhi... Mujhe bs apka support chahiye.. Taki mein bhi kuch sikh sku.. College wale to kuch btaye nhi sirf 3 saal pr certificate thmaa diya... Ab jb mein kuch krna chahta hu to koi support nhi milta.. Kher thank u for rply..
très bon travail je vous admire
Can current controlled really? Nice 👍👍👍
Bahut khub
good viedeo
isbandziau sita schema,gan neblogai veikia.like
Nice video Editing
Super bro
i am alrady subscribe this channel great videos thanks
Hello hello mera solar panel 180w ka hai out put DC 36v he charjar cantolar bana he 36v se 12v ya 36v se 36v
Thank you for your guidence
may i use power rresistor 20W 56R,. . bro?
What’s the input ampere? Can I use 24v 5a power adaptor for this project? Willl it work?
yes it will work
@@KiyanisLab thanks bhai
Vare good
Can I glow a DC 12v 200 watt LED light by using this module... please reply
Its good for regulate current.
Good
Excellent
Sir, i am so impress ,just want to know little think, if you can reply, What is the power factor or efficiency of this circuit? And how much max amp can be use from this circuit? And if u can add digital display then so nice of this circuity.
And one more think can I connect this circuit with my 24v 150ah power bank? Its solar power bank. If I can use then it will be very helpful for me.
LM317 3rd leg is for output, but you connect this leg with Vin. Can you please tell me why?
hi body .i can't undestand how do you conect the green line out of bd139 to 10k potentiometer pin 1 .is it conect to this pin? or it just go to base line of D1047?
Very good. Demonstrated in best way. Can you suggest same type of circuit for up to 0 - to 30 volts with 10 amp. current capacity please ? Thanks.
amazing
sir can manage dc current by this divice when dc motor output is getting up to 1000 volt but we need only 60 volt dc motor and how to see output ampere of dc motor when we torque to motor sir please reply
İ make it. İts very good performance
Oye bro..! Al conectar dos Transistores D1047 en paralelo debo conectar una resistencia de 4.7 ohms 10w en cada patilla de salida de cada transistor..? O solo basta con una resistencia para los dos d1047..? Gracias..!
How many volt did you in
Great work bhai... me wait kar raha tha .... thanks bhai .... great
usama khan lm317 20 ki hey ye mehnga circuit hey
@@nafsiatijana4122 tope itne Kam ka circuit hai Yeh bihi mehanga hao tere, leaya
Can this circuit use for the temperature control of peltier
Thank you kiyan bhai answer daynay kay leya
Can I connect 12v 5ah lead acid battery as input to get 12v 0.5amps output?
@@KiyanisLab
Thanks bro, but I have connected 12v 2A load and large heat sinks to the circuit, it's working fine
Sir ये सर्किट को 12v 17amp की bartty की इन पुट दे सकते हैं क्या
Bhai, D1047 transistor ke badle main aur konsa transistor use kaar sakta hain? please baataye joorur...
good you are .
Whic transistor can I use for more current?? D1047 Or bd 139 transistor?? and how much transistor need for 10A current?? please brother tell me.
2n3055 and c1383 and 3 2n3055 for 10A
WHAT TYPE OF TRANSISTOR YOU USE NPN OR PNP BD139
ALSO I WANT TO CONNECT 5AMP TRANSFORMER FOR THAT WHAT I DO >5 AMP IS VERY GOOD FOR THAT BECAUSE WE CAN CONTROL CURRENT AS WELL >PLEASE ,MUST REPLAY
AND if we connect 4 lm317 in parallel then it can draw 5 to 6amp as well but the transistor use for current thats the problem >if i know that transistor type then its easy for me to find equivalent>
thanks you !
also very nice video >there are many types of videos are in youtube but the current limit function is 1 or 2 videos >
thanks again
KEEP UP
Can i use other any resistor instead of 10w 4.7 ohm resistor
Can i use transeformer to variable power supply?
Try to avoid background music
Its 1000% working thanks
But I'm using it at 36volt and 5amp is it ok
Input kitna de rahe ho
Or kaise
@@ashishstark1741 mai transformer use karra hu 15 0 15 ka ac to dc convert kar k
@@somaiyamusa8853 ok bro thanks
Kya app apna no. De sakte ho kuch muje pucha hoga to aapko puchunga
😀👍👏😊belíssimo trabalho, muito bom.🙏 Obrigado! Show de⚽Sp 🇧🇷☕
D1047 transistor in my city not available. What is its its alternate options.
I Want to regulate 19 volts 120 Ampere DC Current To 14.6 Volts DC 120 Ampere What Shall I Do?
Can i replace 4.7ohm 10 watt resistor with 4.7ohm 2 watt or any low value high watt resistor
nice
Hello bro
I made this circuit it was well running but d1047 transistor got heated up very soon
Today I used my micro motor and it got burned with fumes
Please help me what to do Bhai
And how will I check my transformer amp
Thanks bro
i want 20 amp as Ic. Do i need to use a transistor with "Ic=20amp and Icm = 30 amp" in place of D1047 ??
You would want to use 2 or 3 of them in parallel on a large heat sink for so much current. Check some other videos for how to do that.
@@stevec2196
Can i use two 2N3773 silicon transistor as have Ic =16 amp
@@armancodeq3642 Possibly if the specs are similar to the D1047. Most circuits use two or more 2N3055 in parallel but it wouldn't hurt to try the 2N3773.
Input voltage kitna dena chahiye bhai iss variable dc power supply mai jo aap iss video mai dekhaya haa????
Can you please suggest a circuit/ project of Input Volt AC input and out put will be 12Volt to 30 volt DC with 150Amps without transformer
Nice bro
i have implemented your circuit and its almost working but i m facing little problem that current voltage is regulating with same potentiometer means that voltage control potentiometer is also controlling current while current potentiometer is not controlling current. wht could be the reason of it...reply me soon... i got max 2.2 amp....
@@KiyanisLab thanks for ur reply
What's the difference between your other power supply circuits and this one -
1. One using Lm317, D1047 and Lm358
2. One using Lm723, 2n3055 and D313
Lm317, D1047 and Lm358 easy to build also current limiting
Dude can I use a 5ohm 10w resistor Instead of 4.7 ohm 10w resistor.... And also a 4.7k VR POT instead of 5k VR POT?
Kiyani's Lab so there will be no problem if I use a 12v 3 amp transformer for this circuit
Awesome
Sir kya ham isko mobile shop me power supply ke liye use kare ya nahi
i am doing this very beautiful project.... i hope that you will put a circuit protection on this project....
aapako aasheervaad deta hai
Have you made it?