+Camry le The brightness is pretty much the same with the LED a bit brighter. The difference is the flashing refresh rate with the LED is much quicker which gives a sharper look.
Hi didn't because is hyber flash i just install the same auxbeam 7440 for the back turn signal is start hyber flash need to install load resistor if you watch his other video for the front led turn signal replacement he showed the Different Between the LED and the regular condenser light
strange country might want to consider an led bulb with anti flashing and build in decoder. I seen one on eBay, laserfit brand low end $30 high end $50.
show the difference in brightness between tail and brake light .. when pressing the break .. if there is NO difference then your product is dangerous to be used at night ...
Nice video! Any Lumen information on these bulbs? A side from LM info in Auxbeam descriptions, I also continued to notice that Auxbeam LED bulbs (some Headlight kits, bulbs like those in the video are less bright with life span less than half of other brands (i.e. These bulbs are rated with 20000 hours while others are rated 50000 hours and some even with 2-years replacements...).
I just did them today on the same vehicle. I was wondering if you got the hyper signal on the dash when signaling, if so what did you do to resolve it?
I did not have hyper flash on my Pathfinder. And I have been using it for over 2 years. If for whatever reason, you have hyperflash, you need to install load resistors on each LED light.
Can you help? I am trying to install third brake led strip on my back windshield and connecting to taillight. led stripe has red,black, white, green and 2 yellows, but my 13 pathfinder’s wiring is different. Taillight/brake light has black, green and white. Which one is which how do I know which wire to connect to which wire on my taillight? Do you know where I can find wiring diagram for my 2013 nissan pathfinder for taillight? Any help will be appreciated..
Hello thank you for your videos! I have a question, do these bulbs require you to change the flasher in your vehicle? I am afraid that my cars turn signal would get “hyper flash”. Thanks!
Depends on the car and the LED light you get. What I showed in this video with this brand of LED and this vehicle does not require new flashers or load resistors. Other cars might need it like some Honda.
hey you said the light at the top is the brake light so i watched the video again, is it not actually the turn signals at the top and the brake light is the bottom one. im confused
Maybe a far fetched ?. Does the led light have to be white or can they be red. I’m thinking red lenses red light white lenses white light. What u think?
Well the factory light bulb which is incandescent is not red. Yes the incandescent bulb puts out a warm white light and not pure white, but it does not need to be red since the lens of the tail light is red. Also be careful of some of the red LED light, they are not very bright.
Quick question I encounter a problem where every time I install led lights for my tail light I have a problem where my abs sensor goes crazy and my rpm won’t pass over 2k
These led’s you installed are they white? Because Amazon link you provided takes me to Amazon, but lights are white in color not red. Isn’t it better to install red led on red housing? I am just asking I have heard people say red on red provides more better color then white in red. Thanks for your reply to previous message. I can understand you can only speak for what u have used. I watch your videos a lot because u have 17 pathfinder and my 13 pathfinder is about same in bulbs and other interior and exterior parts. As a matter of fact I saw your video on how to hardwire dash cam and I followed everything in your video and did it myself and I am a female. I love doing car upgrades. I keep watching your videos so I can do upgrades myself. Can u also show or tell how to change the interior front map lights? I have changed all my lights to led’s in my car, but can’t figure out how to change the front map lights. Thanks
If you install red LED light behind red lens, you will get a 'dark' red color output, but it's not as bright. The original bulb is not red, but an incandescent (warm white) bulb. If you install this white LED light, you will get maximum brightness and the color output through the lens is still red but a shade lighter than the incandescent bulb. It's up to you which one you want to install.
dial2fast oh ok, thanks for explaining. I got it. Actually I have a black tint on my tail light. It is not blackout tint, but just black tint by vivid, I can still see the light through the lens even though it is regular bulb, but I was thinking to make it more brighter. So do u suggest I should go with white or red since i have black tint? Would white led make tail light more brighter even with black tint? I am sure it will actually because led are more brighter then regular bulbs. I don’t have any preference. I can go with either I just want to make my tail light more brighter so other drivers behind me can see better. I appreciate your help and answers. You are a Nissan owner too, so that make things very easy for me. Thanks
dial2fast, Thank you sir, appreciate your help. I did order the white ones that you installed on you pathfinder, but in my pathfinder both bulbs are 7334. Tail light and brake light, so I ordered 2 pairs. I checked online my 2013 pathfinder has 7334 for tail light and brake light. Please keep adding more informative videos on your pathfinder. I watch your channel regularly. Thx
dial2fast, ok so here is the thing. My 13 pathfinder’s tail lights are not all red. Yours are. Mine are red on top, but the bottom is White housing. Turn signal bulb is orange and it’s behind the white housing, so mine only has one bulb for brake and tail light. Yours have two separate bulbs. Which is one for parking and turn and one is break. I ordered the auxbeam from your link and installed it. Mine only has one 7443 that’s it. Other one is 7443 too, but it’s orange and for turn signal. My problem is that I installed the led and it looks good, but when I start the car, light flashes twice then it’s fine, so I had to take them off and put back the original ones. Any idea why it flashes when starting the car? I was sure it will work fine, but I don’t know y it flashed twice first when starting the car. It’s 13 pathfinder and your is 17 so, there shouldn’t be any flashing when starting.
Hi I have 2016 pathfinder. There is brake light on the top and Turn signal light is bottom. They are different location between 2017 and 2016 model. What should I buy to change brake light. Please let me know. Thanks
I looked up the 2016, and it uses the same bulb size: Rear turn 7440NA, and Rear stop light 7443. The position might be different but these are the bulbs that's listed. You can also check your owner's manual which has a section on the bulbs to confirm.
I just installed this auxbeam today on my 2017 nissan pathfinder the break light work just fine the turn signal is start hyber flash need load resistor
I have 2013 Nissan Pathfinder and I want to install the led bulbs on my tail light which is 7443. I see few on Amazon. Like alla, senticusa, auxlight etc. can they work on 2013 Nissan Pathfinder or does my car requires any resistors and stuff? Your reply will be appreciated. Thx
Between brands, the brightness can vary, and also some will have better quality than others, so some might last longer than others. Don't ask me if those brands you listed are any good because there are so many out there. I can only tell you the ones I used have lasted. For my 17, I did not have to install any load resistors. You will have to try your 13 and see.
The small little socket is it the same light use for the interior? I already bought the one mentioned above except its Oxilam w/built in resistor in cAse of hyperflash.
Hi buy the 7440 and 7443 led bulb but they are not to bright.. did you think I need resistors? On you video do you use a resistor or which brand you buy?
The smaller bulb that you did not change, will these bulbs work? www.amazon.com/gp/product/B074155L3M/ref=oh_aui_search_detailpage?ie=UTF8&psc=1 I have some left over from the interior change that I did from one of your other videos.
I believe they are also the 194 bulb. It's been awhile since I took them out. But since they are parking light, and don't flash, you really don't gain much with exterior look by changing them. Just my .02
I hoped that you could have made a comparison between the left and right before replacing the left side in order to see the improvement. Thank you
+Camry le The brightness is pretty much the same with the LED a bit brighter. The difference is the flashing refresh rate with the LED is much quicker which gives a sharper look.
Hi didn't because is hyber flash i just install the same auxbeam 7440 for the back turn signal is start hyber flash need to install load resistor if you watch his other video for the front led turn signal replacement he showed the Different Between the LED and the regular condenser light
strange country might want to consider an led bulb with anti flashing and build in decoder. I seen one on eBay, laserfit brand low end $30 high end $50.
@@dial2fast
Finally a video for a 217 pathfinder! Thankyou!
Thank you Bro!! You made my Day!!!! I just done my 2013 rear side parking light bulb replacement .🤩🤩🤩🤩🤩
show the difference in brightness between tail and brake light .. when pressing the break ..
if there is NO difference then your product is dangerous to be used at night ...
Nice vid thank you, I will go ahead and order them from amazon
Nice video! Any Lumen information on these bulbs?
A side from LM info in Auxbeam descriptions, I also continued to notice that Auxbeam LED bulbs (some Headlight kits, bulbs like those in the video are less bright with life span less than half of other brands (i.e. These bulbs are rated with 20000 hours while others are rated 50000 hours and some even with 2-years replacements...).
I just did them today on the same vehicle. I was wondering if you got the hyper signal on the dash when signaling, if so what did you do to resolve it?
I did not have hyper flash on my Pathfinder. And I have been using it for over 2 years. If for whatever reason, you have hyperflash, you need to install load resistors on each LED light.
I believe the 7443 goes on the brake light if I'm not mistaken
Congratulations Man...
Nice Video ! I did iy myself a real achievement Thanks
did anyone know how to replace the 3rd brake light on nissan pathfinder 2014 or 2013.the one on the very top .ill appreciate.
Following
I guess replacing the red big light piece is the same? I have a 2017 pathrinder and the red light is cracked. Is it that easy? Thank you
Can you help? I am trying to install third brake led strip on my back windshield and connecting to taillight. led stripe has red,black, white, green and 2 yellows, but my 13 pathfinder’s wiring is different. Taillight/brake light has black, green and white. Which one is which how do I know which wire to connect to which wire on my taillight? Do you know where I can find wiring diagram for my 2013 nissan pathfinder for taillight? Any help will be appreciated..
Which lights are the correct bulbs for the interior cargo lights? I bought them and it never work
See this video: ruclips.net/video/oUckxvRLA2I/видео.html
I could not find the 7440 in Amber I already replaced the 7443 white for my Taillights. Again I look for 7440 on Amazon in Amber but no luck
Much appreciate your vids! Quick question: What’s the link for the smaller side marker bulb (the one you didn’t replace)?
The rear side marker light is W5W bulb size. Here is a LED one that will work amzn.to/3k7eON4
thx. simple and easily done...
Mine got the hyper flash. Wish I could fix it
It’s exactly what I want. Thank you
Awesome, thanks for your comment!
Gracias amigo, me sirvió mucho.
Hello thank you for your videos! I have a question, do these bulbs require you to change the flasher in your vehicle? I am afraid that my cars turn signal would get “hyper flash”. Thanks!
Depends on the car and the LED light you get. What I showed in this video with this brand of LED and this vehicle does not require new flashers or load resistors. Other cars might need it like some Honda.
Diode Dynamics seller a new turn signal relay for $15 that addresses this issue.
I really want it to match my other Auxbeam. No resistor needed right? On the 7440. Again I need it in amber for my application
hey you said the light at the top is the brake light so i watched the video again, is it not actually the turn signals at the top and the brake light is the bottom one. im confused
He meant to say the opposite, you are correct he just got it reversed.
Maybe a far fetched ?. Does the led light have to be white or can they be red. I’m thinking red lenses red light white lenses white light. What u think?
Well the factory light bulb which is incandescent is not red. Yes the incandescent bulb puts out a warm white light and not pure white, but it does not need to be red since the lens of the tail light is red. Also be careful of some of the red LED light, they are not very bright.
Hey would the parking light be the same as the interior lights?
Can you send the link for parking light? I'm planning to buy all these three at the same time thanks.
Hello.. will this work in 2013 Nissan Pathfinder SV?
What About lamps in the gate can I fix
Thanks
Quick question I encounter a problem where every time I install led lights for my tail light I have a problem where my abs sensor goes crazy and my rpm won’t pass over 2k
What about the lights on the liftgate
These led’s you installed are they white? Because Amazon link you provided takes me to Amazon, but lights are white in color not red. Isn’t it better to install red led on red housing? I am just asking I have heard people say red on red provides more better color then white in red. Thanks for your reply to previous message. I can understand you can only speak for what u have used. I watch your videos a lot because u have 17 pathfinder and my 13 pathfinder is about same in bulbs and other interior and exterior parts. As a matter of fact I saw your video on how to hardwire dash cam and I followed everything in your video and did it myself and I am a female. I love doing car upgrades. I keep watching your videos so I can do upgrades myself. Can u also show or tell how to change the interior front map lights? I have changed all my lights to led’s in my car, but can’t figure out how to change the front map lights. Thanks
If you install red LED light behind red lens, you will get a 'dark' red color output, but it's not as bright. The original bulb is not red, but an incandescent (warm white) bulb. If you install this white LED light, you will get maximum brightness and the color output through the lens is still red but a shade lighter than the incandescent bulb. It's up to you which one you want to install.
dial2fast oh ok, thanks for explaining. I got it. Actually I have a black tint on my tail light. It is not blackout tint, but just black tint by vivid, I can still see the light through the lens even though it is regular bulb, but I was thinking to make it more brighter. So do u suggest I should go with white or red since i have black tint? Would white led make tail light more brighter even with black tint? I am sure it will actually because led are more brighter then regular bulbs. I don’t have any preference. I can go with either I just want to make my tail light more brighter so other drivers behind me can see better. I appreciate your help and answers. You are a Nissan owner too, so that make things very easy for me. Thanks
@@hinniji If your lens is tinted, then I recommend going with the white color. It will be brighter than installing red LED.
dial2fast, Thank you sir, appreciate your help. I did order the white ones that you installed on you pathfinder, but in my pathfinder both bulbs are 7334. Tail light and brake light, so I ordered 2 pairs. I checked online my 2013 pathfinder has 7334 for tail light and brake light. Please keep adding more informative videos on your pathfinder. I watch your channel regularly. Thx
dial2fast, ok so here is the thing. My 13 pathfinder’s tail lights are not all red. Yours are. Mine are red on top, but the bottom is White housing. Turn signal bulb is orange and it’s behind the white housing, so mine only has one bulb for brake and tail light. Yours have two separate bulbs. Which is one for parking and turn and one is break. I ordered the auxbeam from your link and installed it. Mine only has one 7443 that’s it. Other one is 7443 too, but it’s orange and for turn signal. My problem is that I installed the led and it looks good, but when I start the car, light flashes twice then it’s fine, so I had to take them off and put back the original ones. Any idea why it flashes when starting the car? I was sure it will work fine, but I don’t know y it flashed twice first when starting the car. It’s 13 pathfinder and your is 17 so, there shouldn’t be any flashing when starting.
Hi
I have 2016 pathfinder.
There is brake light on the top and
Turn signal light is bottom.
They are different location between 2017 and 2016 model.
What should I buy to change brake light. Please let me know.
Thanks
I looked up the 2016, and it uses the same bulb size: Rear turn 7440NA, and Rear stop light 7443. The position might be different but these are the bulbs that's listed. You can also check your owner's manual which has a section on the bulbs to confirm.
dial2fast
Thanks.
I just installed this auxbeam today on my 2017 nissan pathfinder the break light work just fine the turn signal is start hyber flash need load resistor
I’m having the same issue on the same vehicle was wondering if you found a solution?
@@wilfredoramos3121 the solution is you need to put load resistor on each side i did that and the problem solved
strange country do you have a site where to buy a good load resistor?
@@sc0rpion604 Amazon or Ebay just search for led turn signal load resistor
They all made in China
I have 2013 Nissan Pathfinder and I want to install the led bulbs on my tail light which is 7443. I see few on Amazon. Like alla, senticusa, auxlight etc. can they work on 2013 Nissan Pathfinder or does my car requires any resistors and stuff? Your reply will be appreciated. Thx
Between brands, the brightness can vary, and also some will have better quality than others, so some might last longer than others. Don't ask me if those brands you listed are any good because there are so many out there. I can only tell you the ones I used have lasted. For my 17, I did not have to install any load resistors. You will have to try your 13 and see.
I want ask you , can you make a video for how to change cvt fluied
My car is still very new with 8k miles, won't be changing the fluid for a long time. Thanks for asking.
I installed this one and it hyper blinks. What should I do
what year is your car
Is this the same installation for the 2018 pathfinder sl?
Yes its the same.
The small little socket is it the same light use for the interior? I already bought the one mentioned above except its Oxilam w/built in resistor in cAse of hyperflash.
I am confused. Isn't 7440 and 7443 the same?
7440 is single filament, and 7443 is dual filament
How did you stop the hyper flash?
The combination of these LED lights and this vehicle does not have hyperflash issue.
No I did this mods already
My 17 pathfinder is hyper flashing I ordered both sets you have don’t know why it’s doing this
Is this will fit on 2019 Pathfinder?
Yes
The bulb 7440 and 7443.. are the same??
7440 is single filament. 7443 is dual filament.
Thanks..
Hi buy the 7440 and 7443 led bulb but they are not to bright.. did you think I need resistors? On you video do you use a resistor or which brand you buy?
@@octavioalfaro8153If you don't think the LED is bright enough, then don't do this mod as you won't be happy.
@@dial2fast so it's depend the brand.. I ready order the auxbeam bulbs will see what's happens..
The smaller bulb that you did not change, will these bulbs work? www.amazon.com/gp/product/B074155L3M/ref=oh_aui_search_detailpage?ie=UTF8&psc=1 I have some left over from the interior change that I did from one of your other videos.
I believe they are also the 194 bulb. It's been awhile since I took them out. But since they are parking light, and don't flash, you really don't gain much with exterior look by changing them. Just my .02
Your .02 cents is creditable. I’ll leave it as is. Thank you
Does the 2016 pathfinder need resistors?