Great tutorial on how to install an amplifier for your car audio system! The step-by-step guide made it easy to follow along and understand what needs to be done. Thanks for sharing! #caraudio #ampinstallation #diyproject
Great video! Installing an amplifier for your car audio system is easy when following these steps. Thanks for sharing! #caraudio #bassamp #installationtips
Hey man maybe you help after installing a after market headunit (kenwood) with after market rear and front speakers , no subs no amps, my soeakers sound terrible worst than before, coukdnt even turn up without distortion, so i got a 4 channel amp to power those speakers and my front speakers are so quiet compared to the rear, its bad enoughy i have to turn the head unit volume damm near to 30 just to get some loadness cant harley hear anything at 15, but why is my front speakers so low
They’re gonna sound bad and quite because they’re supposed to be hooked up with an amp. Most aftermarket speakers are designed to be used with an amplifier
Tapped most likely to a fuse down below the drivers side or passenger side maybe IGA1 which is ignition or fuel pump or fuse 18 id check fuse 18 in your manual tho fuse 18 is for my car also I believe there’s a remote wire in the stock headunit you can splice into but that’s a whole lot more work. Make a ring with your remote wire wrap it around one of the silver pieces or rods to your fuse after pulling it out and plug it back in.
you r video should show and talk about the wires connecting to amp with power and remote and what they are. that is what i am trying to lean and all these videos, people skip over that.
When installing the amp I know I ground the amp to the chassis, but do I ground the chassis to the battery? Asking cause the amp says do it this way in the little booklet it comes with.
Bruh my speaker smoking
Damn bruh what song you playing?! 🔥🔥
Speaker chill asf😶🌫️
Bruhhh
😂
Bro just blown his sub
Your next video should be adjusting the sound; radio, amp, and amp at the powered subwoofer. Thx!
Great tutorial on how to install an amplifier for your car audio system! The step-by-step guide made it easy to follow along and understand what needs to be done. Thanks for sharing! #caraudio #ampinstallation #diyproject
Great video! Installing an amplifier for your car audio system is easy when following these steps. Thanks for sharing! #caraudio #bassamp #installationtips
Can you do one with connection of Android radio to external equaliser and amplifier please
But which ports do you plug your RCAs into
Hey man maybe you help after installing a after market headunit (kenwood) with after market rear and front speakers , no subs no amps, my soeakers sound terrible worst than before, coukdnt even turn up without distortion, so i got a 4 channel amp to power those speakers and my front speakers are so quiet compared to the rear, its bad enoughy i have to turn the head unit volume damm near to 30 just to get some loadness cant harley hear anything at 15, but why is my front speakers so low
Did you figure it out
They’re gonna sound bad and quite because they’re supposed to be hooked up with an amp. Most aftermarket speakers are designed to be used with an amplifier
Where did you connect the remote and rc wire too
Tapped most likely to a fuse down below the drivers side or passenger side maybe IGA1 which is ignition or fuel pump or fuse 18 id check fuse 18 in your manual tho fuse 18 is for my car also I believe there’s a remote wire in the stock headunit you can splice into but that’s a whole lot more work. Make a ring with your remote wire wrap it around one of the silver pieces or rods to your fuse after pulling it out and plug it back in.
you r video should show and talk about the wires connecting to amp with power and remote and what they are. that is what i am trying to lean and all these videos, people skip over that.
just remember that the best grounding point is the battery!
that is if the battery is close !
or if you use two batteries !
Where did you buy those spacers?
Hey if to put all cables in drive side is problem?
Yes. Run the power and signal on the opposite side.
@@t8erloveyep
When installing the amp I know I ground the amp to the chassis, but do I ground the chassis to the battery? Asking cause the amp says do it this way in the little booklet it comes with.
Just ground the amp the Chassis.
Im doing an install on an aftermarket radio where do i hookup the remote wire to
Red wire
@@tjbenson6185you wrong bro😂
Imagine if the cordless drill slipped whilst screwing in the subwoofer 😮. That's what hand tools are for
Can I use any hi to low adapter ?
yes you can.. depends on the car ! not every car needs a hi to low converter/adapter
Why do you run the RCA cables and signal cables on the opposite side of the power cable???
To reduce feed back.. on subs it’s not that big of a deal vs an amp for mids and highs but it’s good practice
@@BreakersStereo any idea why my subwoofers would be humming extremely loud as soon as I power on the head unit
Mine has kickback when I turn mine off
Interference from the power cable
When I put the cable to positive my battery is being drained
3:27
Im excited
Me too!! 🤣🤣🤣
Good day po how much subwoofer amplifier set up
$150
What soeakers did you attach to the adapter
2 12s n 1200 wat
Mines not working at all
Check power and ground wires
Just did mines yesterday bro it's working it's probably just a wire that's not working for you
Not me. I bought a 4 channel amp. I dont need a subwoofer. I like my music loud but care much for a lot of bass.