Perfect example of how a video should be made . Easy step by step and simple techniques which makes me come back to your videos for all my repairs. Well done .
You didn't see his beginings. We supported him, but I couldn´t understand half a video, because I´m not native speaker, also. His english is pretty fine now! Improved a lot.
This video should be viral.HollyWood could'nt make this.Dracula fixing a cars ABS fault at night.He speaks exactly like dracula his tone rate and speed.Dang it's night time dark he films it in high quality video with a led shop light.Really a great short video
Man is anyone thinking like what I'm thinking that he sounds like Sesame street Count Dracula. Either wise that's a great video, will check it out on my car thanks.
Peter Finn, I hope you did not take offence at my comment. You have a distinct accent which reminds me of Western European, the lighting in the video and the cadence in your voice almost made it seem the repair was done in secret. (made the video entertaining) My ABS light went on in my van the other day and your fix should be what a DIY person should attempt. I used your method.
DeWALTer_White: i like this video. It is well done and the guy is trying hard to give the best tech explanation in english, which is not his native language. Question is, how good we are to give same explanation in another language that is not ours. Anyway we agree: Great job with this vid. Peter, thanks!
I like a video where they use an actual older vehicle as the example. Most videos use a new car, everything fairly clean and easy to fix. This is a real-world situation like most of us would find. Rusted hub where sensor mounts, trying to fix something late at night with a flashlight, and not always all the perfect tools for the emergency job. That's why it's DIY. Well done!
Tip: When bolts break off and sensor can not be removed, drill right through them with closest sized drill bit to size of sensor. Remove any residue left in hole and make sure no material gets trapped between teeth on sensor ring. Take new sensor and apply a 1/4in ring of silicone sealer on new sensor's base and place sensor all the way down until it is flush with hub surface. Let silicone dry for about 20 minutes and reconnect wire as required. If you ever have to pull sensor out again, it will come out easily since no dirt or rusty bolt will be holding it in place. Never had one pop out, even on off road vehicles.
I just went through this job and believe me, you need to pull the hub off to do a thorough job cleaning the ring gear and backing plate. Plug the bearing races and power wash the ring gear and inside of hub.. Lots of places for magnetic trash and metallic dust to hide. After my first attempt of pulling sensor and cleaning gear through the hole, the ABS light returned in a few miles. I pulled the sensor again and it had a full beard of magnetic dust again. Time to pull the hub and get serious. Power wash hub interior (with bearing area sealed off) and backing plate. Dry with compressed air at full force.
Yeah, some parts are really pretty rusty out there, I think You definitely can fix them up and running pretty well - thnx Peter 👍At least its pretty nice that wheel bearings is still in good conditions.
😂🤣😆😆😆 ... I felt that I was listening to a Russian Mobster working on his car at night in his spare time...to stop himself from gunning down his lousy henchman. Looooooooll. Great video. Don't come after me. ☺😂👣👀🤣🤣🤣🤣😆 Respect!!! Thank you from Aamerika!!
I found it very comical to hear many of you guys fixed on this nice guy’s accent , but pretty sure he speaks more than 5 languages , as most of us Europeans do . Question to all these douche bags , how many languages do u speak , besides English ??. Hey Pete never mind these knuckle head comments , you did a great job on this .
لكُل فني أوهآوي شخصياً من هوآة أعملها بنفسّك ( DIY ) من الضروري يكون من ضمّن عدتّك قيآس الكلّبّر سلآيد caliper slide أقل شيء ولو عندّك معهُم المكرومتّر micrometer . لكآن زيآدّة الخير بركّة /// سهل أستخدآمهُما وأذا صعُب عليك أستخدآم أياً منهما أكتــُب بالغوغّل gogoole كيف تستخدم !!! How to use caliper slide how to use micrometer gauge وروح للأشرطّة / المقآطّع ( فديو Video ) لقياس وووقرآئــة سمآكّة قُرص الفرآمّل ( الروتّر rotor ) ؛ أفضل آستخدآم قيآس الكلبّر سلآيد caliper slide عن أستخدآم المكرومتّر micrometer لأن أستخدآم الكلبّر سلآيّد caliper slide وقرآئتهُ أفضل وأضمّن وأسهـّـل . You can measure the brake rotor minimum thickness with caliper slide or with micrometer . For me I rather and . preferred use caliper slide مُلآحــظــّـة مُهمّة جداااً ؛ لا تستخدّم زيت غير الزيت الموصوف لفرآمّل سيآرتّك !!! مثلاً ؛ أذا مكتوب على غطاء علبّة الريت اللي فوق الكبآس الشيخ زيت عيآر دوت 3 DOT فضروري تضيف له زيت ( سآئل ) من نوع / لزوجّة ( عيآر ) دوت 3 === 3 DOT اللي هي نفس علبّة 21 . هنا تقدّر تضيف لُه زيت / سآئل عيآر دوت 4 ========== DOT 4 . ولآكن ليس العكّس /لا تُضيف دوت 3 === 3 DOT لزيت دوت 4 ==== DOT 4 . طــبعاً ؛ فيه دوت 5 --- DOT 5 وفيه دت 6 --- DOT 6 لا تخلطهُم أبداً .
Thanks for posting, but did the sensor ring cleaning work? Presumably you had an ABS fault message? I'm trying to resolve an ABS fault message from the right hand rear wheel of my 2002 Volvo V70XC and the ABS sensor ring is difficult to clean as it's concealed and only accessible by removing the sensor and inserting a small file into the sensor hole and you can't see what you are doing. Any advice would be appreciated thanks.
Nice video by Peter Finn. Taking ones time and dealing with the little details is the key to getting to the desired result. "It can´t be nothing. It must be totally clean". How true.
I'm an immigrant but so far I think than this is the ever worse accent than I heard in my last over 20 years. This could be a great accent for a stand up comedy... Im just wonder if this is his first job in America... Other than that, he made a pretty informative video for many people from youtube. I will give him a huge thanks for his very unusual effort!
My abs light came on twice yesterday. I think I will do some cleaning. I will check if my Dremel has some sort of small wire brush that fits inside the sensor hole, this way I can use the dremel while rotating the shaft to clean the abs ring all around without taking the disk and hub assembly off.
What vehicle was this done on... as I have a Subaru Impreza with eminent ABS warning light coming on along with the Traction light, very annoying hoping to clean the ABS and this will solve the issue???
On old cars i find the abs sensor often breaks trying to remove it. Or those little bolts snap. If it doesn't want to come out loosen the axle nut and push the shaft back enough to see the ring and wash it that way. Also check if it's cracked or loose.
problem facing in Chevrolet captiva, DTC U0073, U0121 and P0500 ,,,,suddenly odometer stops working ,all needles(Temperature, rpm, speed etc.) showing 0 reading , ac stops cooling while blower keep running,reverse gear light stops working and all happen intermittently and all together. Can anybody suggest solution?
Good video but the comments make it sound like a chat room. Question friend, did that fix the problem? Also, was the sensor riding on the Tone Ring / Reluctor. Mine has a beveled / rounded shape on my rear sensors and now have two codes cuz I messed with the other passenger side. P1774 and P1775. The sensor is not supposed to touch the reluctor right. Thanks, Great video!
Abdur, you can see on the video that Peter is working on the front right side. The abs ring usually is located on the same place on most cars . On my kia is on the same place.
Peter can you help me, my Toyota Corolla 1997 the check engine light 💡 has come on after i start drive the car 🚗 some times when i drive to the city and and turn the engine off and after that start the car the check engine light 💡 not come on and sometimes she come on when i go over speed 60 km and some times she go off automatically and sometimes she come on when the car gets move . Please help, thank you 🙏
I know that hub. ! The Simpler way is to pop the bottom balljoint and then remove the rut from the drive shaft. Then simply push the drive shaft out. If your going to that extent id recomend fitting a new pair. The parts pritty cheap. Reluctor Ring. Or Triger Ring. Ebays easyest
Okay I'm dealing with the Incredible Hulk that can turn a driveshift connected to a transmission lol but just wondering why since you had that monster strength, why didn't you just put a magnet pick up tool in the hole as turning it?
I have a problem. On my 1996/7 Volvo S40 I cannot pull the wire out of the sensor. I have the whole wheel hub together with the ABS wiring from a 98 car from a junkyard but I cannot pull the wire out of that one either. Any tricks on how to do it on old, more rusted cars? Can you use certain chemicals to help it wiggle out or will that damage anything? The ABS light is constantly on, the whole system has disabled itself. The speedometer and odometer work though. The ABS system stopped working after a wheel bearing replacement job.
Did this fix your problem. I changed the wheel bearing in a 2013 Nissan rogue the The shield on the new one came off and cut the speed sensor off. When I took the old one off I twisted the bolt off holding the sensor so I did what the guy before you did and used the self tapping bolt to hold it in but my abs system isn't working I'm lost on what the problem could be. The New bearing, new sensor or something else I'm going to try to do this next. Thanks for the info
He doesn't play music loud over his talking , and I found him easy to understand . And makes it simple .
Great info and Thank You. :-)
I feel ya man, I hate the videos with all the dang music, I need information, not entertainment.
Perfect example of how a video should be made . Easy step by step and simple techniques which makes me come back to your videos for all my repairs. Well done .
Glad you liked it!
I appreciate how well this video is hard this guy is helping trying very hard in English brilliant video
Thanks. :-) I really appreciate your comment.
como localizar el filtro de la gasolina en un honda accord del2003
You didn't see his beginings. We supported him, but I couldn´t understand half a video, because I´m not native speaker, also. His english is pretty fine now! Improved a lot.
I'm from Finland and definetly he is a native Finn, it is very easy to recognize his accent.
the james bond of mechanics..''I take my 10mm shocket..''
James Bond is create person. :-)
DCTV DubzCo
0
I have a Lexus 300 which the speedometer is not waking what should I do.
I have a Lexus 300 which the speedometer is not waking what should I do.
I have a Lexus 300 which the speedometer is not waking what should I do.
Peter, I appreciate your easy to see and understand videos. You have saved me a lot of money by allowing me to repair these things myself. BRAVO!!
He’s 100% Finnish haha. Talks like my dad. Love it
This video should be viral.HollyWood could'nt make this.Dracula fixing a cars ABS fault at night.He speaks exactly like dracula his tone rate and speed.Dang it's night time dark he films it in high quality video with a led shop light.Really a great short video
Thanks ! 👍😃
A proper mechanic that gets to the route cause of the issue and doesn't just say "It's the ABS control module mate, that'll be £100!"
Man is anyone thinking like what I'm thinking that he sounds like Sesame street Count Dracula. Either wise that's a great video, will check it out on my car thanks.
Ahahahah! This guy is awesome! One sensor, ah ah ah, two sensors! Ah ah ah
Who's fixing this car!? Dracula !!!??? Loved it.
Yeah ! Here is the Man, what likes beef.
Peter Finn, I hope you did not take offence at my comment. You have a distinct accent which reminds me of Western European, the lighting in the video and the cadence in your voice almost made it seem the repair was done in secret. (made the video entertaining) My ABS light went on in my van the other day and your fix should be what a DIY person should attempt. I used your method.
ha,ha,ha
DeWALTer_White: i like this video. It is well done and the guy is trying hard to give the best tech explanation in english, which is not his native language.
Question is, how good we are to give same explanation in another language that is not ours.
Anyway we agree: Great job with this vid. Peter, thanks!
DeWALTer_White 😂😂😂
I like a video where they use an actual older vehicle as the example. Most videos use a new car, everything fairly clean and easy to fix. This is a real-world situation like most of us would find. Rusted hub where sensor mounts, trying to fix something late at night with a flashlight, and not always all the perfect tools for the emergency job. That's why it's DIY. Well done!
Thanks 👍😊
I just have to say: Pretty nice finnish English - keep going, Peter 👍😇
Thanks for taking the time to post your experience, much appreciated.
Thank You for feedback. :-)
Great videon..i cleaned my abs sensors n abs light went out...thank you..
Thx for great video. I now know exactly where sensors are and what to look for. Plz keep up with more great info videos.
Thank You. :-)
These are my jeans, a shorter model *shows ripped up pair of trousers*. Great video.
Ok
😂🤣👏
Tip: When bolts break off and sensor can not be removed, drill right through them with closest sized drill bit to size of sensor. Remove any residue left in hole and make sure no material gets trapped between teeth on sensor ring. Take new sensor and apply a 1/4in ring of silicone sealer on new sensor's base and place sensor all the way down until it is flush with hub surface. Let silicone dry for about 20 minutes and reconnect wire as required. If you ever have to pull sensor out again, it will come out easily since no dirt or rusty bolt will be holding it in place. Never had one pop out, even on off road vehicles.
Thanks 👍
Thanks for comment. 👍
Watching the video for ASMR.
Thanks, you have really helped me with a constant headache.
Hi Sir and Thank You for feedback. :-)
Know we know what happened to all the spies from ''Hogan's Heroes'' !
Thanks for comment 👍😀
KGB agent for sure
Hi very good video brother. Very informative and very professional. Love it. Thank you for making it clear on how to do this job 👍🏾👍🏾😃😃😇😇
Thank You. :-)
My car had the Censor change and cleaned and it started acting up in a two week time why?
I just went through this job and believe me, you need to pull the hub off to do a thorough job cleaning the ring gear and backing plate. Plug the bearing races and power wash the ring gear and inside of hub.. Lots of places for magnetic trash and metallic dust to hide. After my first attempt of pulling sensor and cleaning gear through the hole, the ABS light returned in a few miles. I pulled the sensor again and it had a full beard of magnetic dust again. Time to pull the hub and get serious. Power wash hub interior (with bearing area sealed off) and backing plate. Dry with compressed air at full force.
Great and Thanks for comment. :-)
napalm works too
You probably could clean the ABS ring from under the drive shaft with a wire brush quicker than through the hole.
I didn't understand a word he said, but the video helped me clean my abs sensors.......go figure.
Yeah, some parts are really pretty rusty out there, I think You definitely can fix them up and running pretty well - thnx Peter 👍At least its pretty nice that wheel bearings is still in good conditions.
In other way, you can use carburetor/throttle body cleaner. Just spray at the area that have dirt/debris.
Thanks 😀👍
Not brake cleaner?
😂🤣😆😆😆 ... I felt that I was listening to a Russian Mobster working on his car at night in his spare time...to stop himself from gunning down his lousy henchman. Looooooooll. Great video. Don't come after me. ☺😂👣👀🤣🤣🤣🤣😆 Respect!!! Thank you from Aamerika!!
Oh wow!
Wouldn't be easier to clean it with brake fluid
hello, a little late to the party, But can I use some carb cleaner or brake cleaner on the inside wheel?
Something about a Russian accent and brakes....😃😃
I really enjoyed this video. Hard to get camera focus, light and tool to come together. Great job on what I was interested in.
Thanks ! :-)
Love your accent mannnnnn👍👍👍👍
Thanks! :-)
I found it very comical to hear many of you guys fixed on this nice guy’s accent , but pretty sure he speaks more than 5 languages , as most of us Europeans do . Question to all these douche bags , how many languages do u speak , besides English ??. Hey Pete never mind these knuckle head comments , you did a great job on this .
Hi and Thanks ! :-)
لكُل فني أوهآوي شخصياً
من هوآة أعملها بنفسّك ( DIY )
من الضروري يكون من ضمّن عدتّك
قيآس الكلّبّر سلآيد caliper slide
أقل شيء ولو عندّك معهُم المكرومتّر micrometer .
لكآن زيآدّة الخير بركّة ///
سهل أستخدآمهُما وأذا صعُب
عليك أستخدآم أياً منهما أكتــُب
بالغوغّل gogoole كيف تستخدم !!!
How to use caliper slide
how to use micrometer gauge
وروح للأشرطّة / المقآطّع ( فديو Video )
لقياس وووقرآئــة سمآكّة
قُرص الفرآمّل ( الروتّر rotor ) ؛
أفضل آستخدآم قيآس الكلبّر سلآيد caliper slide
عن أستخدآم المكرومتّر micrometer لأن أستخدآم الكلبّر
سلآيّد caliper slide وقرآئتهُ أفضل وأضمّن وأسهـّـل .
You can measure the brake
rotor minimum thickness with
caliper slide or with micrometer .
For me I rather and
. preferred use caliper slide
مُلآحــظــّـة مُهمّة جداااً ؛
لا تستخدّم زيت غير الزيت
الموصوف لفرآمّل سيآرتّك !!!
مثلاً ؛
أذا مكتوب على غطاء علبّة الريت اللي فوق الكبآس الشيخ
زيت عيآر دوت 3 DOT فضروري تضيف له زيت ( سآئل )
من نوع / لزوجّة ( عيآر ) دوت 3 === 3 DOT اللي هي نفس علبّة 21 .
هنا تقدّر تضيف لُه زيت / سآئل عيآر دوت 4 ========== DOT 4 .
ولآكن ليس العكّس /لا تُضيف دوت 3 === 3 DOT لزيت دوت 4 ==== DOT 4 .
طــبعاً ؛
فيه دوت 5 --- DOT 5
وفيه دت 6 --- DOT 6
لا تخلطهُم أبداً .
This sucls without loud techno beat music over playing instructions 👎
Thanks for posting, but did the sensor ring cleaning work? Presumably you had an ABS fault message? I'm trying to resolve an ABS fault message from the right hand rear wheel of my 2002 Volvo V70XC and the ABS sensor ring is difficult to clean as it's concealed and only accessible by removing the sensor and inserting a small file into the sensor hole and you can't see what you are doing. Any advice would be appreciated thanks.
Hi, please use tester. It tells the accurate part
My super secret 10 mm ice pick agent for real silver sufer w210 wagon 4matic will ride and rollout once again thanks for the guidence.
I knew I wasn't the only one that works on cars with no pants on...
what car and year your working on? I checked my abs and wasn't able to find this.
Nice video by Peter Finn. Taking ones time and dealing with the little details is the key to getting to the desired result.
"It can´t be nothing. It must be totally clean". How true.
Hi, Thanks for comment. :-)
I always wondered what happened to Count Chocula.
1:56 shock it!
Kiitos kommentistasi😀👍
Thankyou for your video 👏👏👏👏
Brilliant advice there.
Take care car friend.
As I spin the CV shaft, I spray the ring with brake cleaner and after use air compressor to blow out anything in there.
Ok
Insert a brush in the hole and spin the disk, then blow with air gun, the spray WD-40 while you spin the disk, and you'll be fine for a while.
Many Thanks 😀👍
Does all e91s have that abs ring? I think i don’t have it. Ps, hyvä video!
Thank You and same to You. 😃
Your voice is so familiar, you sound like Count Dracula from the Sesame Street 😂 thanks for the video bro 👌🏻
Lots of people have made this joke, I can count 1 person, 2 persons, 3 persons ah ah ah
🧛🏻♂️
How can I no if the sensor is not working
Error light
Ok thanks
You've got one of the easy ones! On my Chevy Trailblazer the brakes and rotors have to come off.
Noted 👍
I'm an immigrant but so far I think than this is the ever worse accent than I heard in my last over 20 years. This could be a great accent for a stand up comedy... Im just wonder if this is his first job in America... Other than that, he made a pretty informative video for many people from youtube. I will give him a huge thanks for his very unusual effort!
Thanks Sir, Great Comment. I speak also Spanish. 😀👍
My abs light came on twice yesterday. I think I will do some cleaning. I will check if my Dremel has some sort of small wire brush that fits inside the sensor hole, this way I can use the dremel while rotating the shaft to clean the abs ring all around without taking the disk and hub assembly off.
Good work
I wish. The abs ring on my Jeep XJ is terminally corroded. Years of pulling boats out of the Scottish sea...😭
Thank You for Your comment my Friend. 😀
Thanks, Peter. Very clear and informative. I haven't touched these ABS parts since they were invented!
Thank for feedback. :-)
Same do I, because still there is no reason for that. ☺
I hv a Benz 190E, I really appreciate your videos to clean ABS of my car .👌
What vehicle was this done on... as I have a Subaru Impreza with eminent ABS warning light coming on along with the Traction light, very annoying hoping to clean the ABS and this will solve the issue???
Toyota Corolla
I wiped the rust particles off of the sensor and bead blasted the sensor ring. Then I oiled the sensor ring and the problem was solved.
Good !
Can you cleen those theeth in the hole with brake cleaner? Maybe for a cleaner clean.
Yes
On old cars i find the abs sensor often breaks trying to remove it. Or those little bolts snap. If it doesn't want to come out loosen the axle nut and push the shaft back enough to see the ring and wash it that way. Also check if it's cracked or loose.
Good comment and Let's All folk discuss more 👍😀
maybe dremel's small metal brush gonna be good for "supersonic speed cleaning"? what do u thinking?
Thanks and Good comment. :-)
if i get the failurecode U1417 by a dodge that says unplousible signal on left tire is THAT the failure on it ?
Noted 👍
Can these teeth be cleaned by extra breakcleaner? Good video thx, bob the Belgian🇧🇪🍺
I was wondering too. Probably seeing as it evaporates and is okay for electronics
Thank you Peter. You have a new sub. I've been having random dash ABS light on recently, I will definitely try this as a starting point.
Thanks for the sub!
Now I'll take my jeans - a little bit shorter model :)))))
is where I started to laugth: thanks for a nice sence of humor and video.
@Alexander Skurl... I just found this channel ya'll. These comments got me 😂😂.
It’s the guy from Despicable me! Where’s the minions 😁
Thanks
Thanx! Will have a go myself now I know how to do it.
Have fun!
nice enough guy, but blowing compressed air around brake components? yikes... I hope you have #1 top Russian face mask on face comrade!
Thanks for the tips!
The Wind apparently doesn't blow where @beansandcorn123 is from, at least there is no road dust.
What car? Model? It’s not like mine. Yet it’s basically the same, sure
Corolla 2005
Takie sciemy,o wyciaganiu reka czujnika ABS z widocznie leciwego auta to mozsz pan dzieciom jako bajki puszczac.
Cheap repair become expensive, if you can not buy a new sensor and a new ring which is cheap then why have a car lol.
Thanks for comment. 👍😀
was this car submerged in salt water? those discs are very corroded......
FRom Okhaholma....Thanks 👍😁
problem facing in Chevrolet captiva, DTC U0073, U0121 and P0500 ,,,,suddenly odometer stops working ,all needles(Temperature, rpm, speed etc.) showing 0 reading , ac stops cooling while blower keep running,reverse gear light stops working and all happen intermittently and all together. Can anybody suggest solution?
worthwhile watching only for the beautiful finnish english accent
👍
Hi Peter,
Wasn't it easy to use a small wire brush which can be rotated to clean the ring?
Yes, it should be good idea. :-)
1959 dodge d100 rear end differential front ceal 2wheel drive
Ok
Can i clean with some spray? Spray for clean brakes?
Yes
Is spraying with brake cleaner or electric cleaner ok?
Both works
Good video but the comments make it sound like a chat room. Question friend, did that fix the problem? Also, was the sensor riding on the Tone Ring / Reluctor. Mine has a beveled / rounded shape on my rear sensors and now have two codes cuz I messed with the other passenger side. P1774 and P1775. The sensor is not supposed to touch the reluctor right. Thanks, Great video!
sir, my car also showing abs sensor problem this sensor which side back or fornt break pls.sir explain me.
Hi, you must replace sensor
Abdur, you can see on the video that Peter is working on the front right side. The abs ring usually is located on the same place on most cars . On my kia is on the same place.
10mm shocket for the ABS sensor 😉
Thanks Sir. :-)
A great DIY well presented video. Thanks.
valuable Peter, thank you for your good work ...
Hi, I got to the cleaning part. Wheel off and all. How do you rotate the wheel freely? I just didn't want to risk taking the car off emergency brake
Easy
Peter can you help me, my Toyota Corolla 1997 the check engine light 💡 has come on after i start drive the car 🚗 some times when i drive to the city and and turn the engine off and after that start the car the check engine light 💡 not come on and sometimes she come on when i go over speed 60 km and some times she go off automatically and sometimes she come on when the car gets move . Please help, thank you 🙏
I know that hub. !
The Simpler way is to pop the bottom balljoint and then remove the rut from the drive shaft. Then simply push the drive shaft out. If your going to that extent id recomend fitting a new pair. The parts pritty cheap. Reluctor Ring. Or Triger Ring. Ebays easyest
Thank you!😀
Can we add grease from that hole to the wheel bearing?
No
Couldnt you use throttle body cleaner to clean the senser wheel ?
Good point
Thank you for the explanation
Okay I'm dealing with the Incredible Hulk that can turn a driveshift connected to a transmission lol but just wondering why since you had that monster strength, why didn't you just put a magnet pick up tool in the hole as turning it?
Noted 👍
the "jeans" look more like chinos! But very helpful video - thanks!
Ok
I have a problem. On my 1996/7 Volvo S40 I cannot pull the wire out of the sensor. I have the whole wheel hub together with the ABS wiring from a 98 car from a junkyard but I cannot pull the wire out of that one either. Any tricks on how to do it on old, more rusted cars? Can you use certain chemicals to help it wiggle out or will that damage anything?
The ABS light is constantly on, the whole system has disabled itself. The speedometer and odometer work though. The ABS system stopped working after a wheel bearing replacement job.
Did this fix your problem. I changed the wheel bearing in a 2013 Nissan rogue the The shield on the new one came off and cut the speed sensor off. When I took the old one off I twisted the bolt off holding the sensor so I did what the guy before you did and used the self tapping bolt to hold it in but my abs system isn't working I'm lost on what the problem could be. The New bearing, new sensor or something else I'm going to try to do this next. Thanks for the info
Sensor replace helps too
Mr peter do toyota corolla AE 100 use abs sensor
Noted 👍
Yeah the phonics change the video world, really cool .
Thank You Peter , now I am less worried about doing the job. Just have to figure out which one is bad.
Thank you for comment. :-)
I have been advised at MOT my sensor housing port needs changed..Megane mk2 gt turbo. Looking for information on the difficulty & cost of the job
Ok and thanks. 👍😀
Is it possible that ABS light goes off by doind this?
Yes
@@PeterFinnTheCarDoctor ok tnx
ABS sensor is outside! It's always dirty! Cleaning it will do nothing!
If its the right sensor. It is damaged and will need to be replaced!
Thank You for Your comment my Friend. 😀
Spray some brake cleaner and it will clean up good
Good
Good
Piston ring opel kadeet c16nz installation