Oh thank you man! I try to share tidbits everytime and it may seem in scattering the tidbits all around the videos so they all would watch? Kinda not intentional as engine projects vary and there are some that isn’t related While there are a few that becomes the perfect examples So it is as fun for me while I shoot the videos man :)
Cylinder bore is actually decent, just looked kinda rough after we cleaned it so it was free of oil and such and Ofcourse had to quickly spray wd40 to prevent flash rust It always looks rough after having it cleaned (the old oil always makes it look “okay” ) That’s what makes it hard purchasing used blocks cuz if u pull the head? It “looks” alright until… lol But yes IF honed? Nothing beats that ftw
@@SRDmotorsports Thanks Ralph! Do you know if the pockets are deeper on the YCPs? I'm concerned about the piston-to-valve clearance on a B16A with Tuner 2s.
Ah if it’s b16a 81mm then it’s not related to how b20 pistons are regardless of brand But the 81 is prolly close to CTR so that might be fine after checking clearances
Hi from uk im trying to find pistons to suit b20z with gsr head but really want no higher than 11.5.1 compression im using itr cams this why i change pistons as i understand intererance on valve reliefs Spent the last few weeks hunting for parts but very hard to find anything that dosnt exceed 12.5.1
Oh nice that will be a bigger “beast” 😅 No trouble with the GSR head check this video of ours for the things u need to do to your gsr head so it is ready for a b20vtec conversion application Feel free to ask anything on it man ruclips.net/video/8ERcLeY56Zo/видео.html
No not yet but that would be substantially good on the mid range and torque with a bit of top end That’s what I suggest the owners After they max out the CTR cam and eventually beat their currrent 13.5sec time, Pro1 is my next suggestion
Ive build 2018 a B20 Block with Nippon 84.5mm CTR Pistons, with skunk2 pro 2 cams and it made with pump gas and small exhaust 243hp. With bigger exhaust and no catalytic converter it made over 255hp..engine runs till today without problems.
more than that, whatever the stock bore is as long as it’s perfectly round and honed that’s good I see a lot of nonesense locally where they run oversized rings and file it to fit not understanding the whole ring consistency to bore is no longer perfectly round… plus they also added % more added windage loss
Even Jaspers b20vtec on 1Up cuz it’s stock bore we made sure the bore is “true” and round and not oval, has 0.0025” piston to wall.. thats 0.06mm since 2018 it’s been running 12.5s and a street car, the full set up is on the video it’s shared I know some did the exact same set up and made 214whp only and 13.3sec 🤣 must of wanted it the way of the local myth builders
@@SRDmotorsports so that block guard is reliable in the engine? the cylinders will last? on stock block without dartons that walls are safe for how much power in your exeprience ? rev 8100? max?
we build now third time b20.. 13 compresion b16 pilished ported head camcats cams block is honded on 85mm with block guard.. need to dyno it and tune.. but like we now its very risky to rev it up now without dartons and block girdle.. 😅
@@josephzaja9210 watch the latest video the b20 rebuild hehe running since 2018 also but now bent valve but block is still okay… Btw what are you guys using to tune with?
hello srd! fan of your videos, do these rods clear oem style b20 pistons well?? (thinking of the ycp p73 style 84mm pistons) the SF website says rods won't clear oem pistons but was thinking that might be a smaller bore b18 problem with this connecting rod. thanks for awesome build video
Love me some b20 vtec builds, my personal favorites , also why H beam and not I beam rods? I know H beam is stronger for boosted applications but heavier, I beam is very strong as well but lighter, I see I beams more fit for an all motor street/track applications
@@StraightOutThaGudda4U hurts my wallet if it was mine hahaha kidding hahah….I’d be tempted to find a t3/t4 just so the rods are at the right place hahaha
@@SRDmotorsports same here I’m running ultra right now even thinking of adding skunk2 piston and rod see how compares to my current type r piston rod crank camshaft cam head package replace with all skunk 2. Was told power is not good for amount of money but what’s not lol 😂
What you mean crankshaft area? Can u identify a “time” marker so we can check? If it’s under the block the brown color is the block having the old oil bed into it (previous owner used old oil too long lol) But it’s cleaned up good
@@SRDmotorsports at 7:12 like the walls looks rusty, or its the old oil. Btw will you make a vid explaining in depth about head porting diy? Like throat ratios and all that Thx!
@@hox2596 yeah 7:12 is old oil that’s cooked it’s not rust cuz it’s aluminum… That video might be too long and too hard to make cuz it’s too “generalized” to do so.. example if on. PR3 head the “bowl” oft times does not need to go too big = it’s already big So in general the throat is more important here But on a D16 the bowl may be a different story…then if we switch it to another brand like Toyota or Volvo (factor in displacement and piston speed) it goes a little bit different again
Actually…as u mentioned it, we never ran a block guard on Hondas I mean the darton MiD sleeves have it built in so it’s fine But Honda’s floating system (not closed deck) has proven to be awesome so we don’t usually run a block guard (The 12.5s we did doesn’t use it) However this block? They built this prior to going to us so we left it as is (they had it all along)
Good day sir, i think i've heard you say you're using a want win adjustable cam gear in one of your build, can you please help me be enlighten? I am also using a want win adjustable cam gear on a sohc engine but upon setting the cam on tdc using the stock cam gear and putting the want win they wont line up perfectly, to be perfectly tdc like the stock cam gear i need to retard the want win a few degree, is this normal?
Yes first of all good Job man! I think want win has two kinds but unlabeled it could be y series (vti) or z series (p08) I say this because my want win seems “normal” for my esi engine on esi head which is set like a p08 But a customer has it and it’s off by 4degrees and to find out? U use ur stock camgear and match the “kunya” to where stock is and that is your ZERO So yeah u can either retard or advance a few deg to match the zero of ur stock camgear
@@SRDmotorsports thank you very much for your fast response, it seems that the want wins tdc mark is advance a little further compared to the stock gear🙂
@@renesandoval7515 amen brother just sharing the love and will keep sharing indeed as I’ve been lucky to meet a few OG back in the forum days and be actual friends and pass on some goods…we make use of the platform we have now for real
Ralph, I always learn something new on your videos. Thanks a lot!
I appriciate that brother!
I wish you were my Nextdoor neighbor. 😆 💪. Awesome 👏🏽 videos thanks amigo
Oh thanks man! next door neighbor got to have good food always? Haha
Great video everytime I wacht one of ur videos I learned something new great content 👍
Oh thank you man! I try to share tidbits everytime and it may seem in scattering the tidbits all around the videos so they all would watch? Kinda not intentional as engine projects vary and there are some that isn’t related
While there are a few that becomes the perfect examples
So it is as fun for me while I shoot the videos man :)
Always watching your videos sir. hope to have an engine build from your shop someday super quality
Oh thanks for those words man! Very much appreciated! And glad what we do… entices proper direction and goals for most :)
Ah if it’s a 81mm bore then it’s diff than the b20
It’s prolly close to CTR which would be fine
As usual, awesome vid. Thanks for the tips 🙏🏼
Yes sir I’m glad it’s useful for all of you guys :) so we all go fasteeeer :)
you have good knowledge
Thank you for the kind words… we always try to share what helps others :)
Awesome video as usual! The cylinder walls looked slightly rough from the video. Would this not affect the build?
Cylinder bore is actually decent, just looked kinda rough after we cleaned it so it was free of oil and such and Ofcourse had to quickly spray wd40 to prevent flash rust
It always looks rough after having it cleaned (the old oil always makes it look “okay” )
That’s what makes it hard purchasing used blocks cuz if u pull the head? It “looks” alright until… lol
But yes IF honed? Nothing beats that ftw
What is the difference between the YCP Gen3 (and how to identify them) and Nippon Racing CTR pistons?
I believe the NPR pistons don’t have the pockets looking like it’s machined after casting
The difference? Little to none compression wise
@@SRDmotorsports Thanks Ralph! Do you know if the pockets are deeper on the YCPs? I'm concerned about the piston-to-valve clearance on a B16A with Tuner 2s.
Ah if it’s b16a 81mm then it’s not related to how b20 pistons are regardless of brand
But the 81 is prolly close to CTR so that might be fine after checking clearances
Hi from uk im trying to find pistons to suit b20z with gsr head but really want no higher than 11.5.1 compression im using itr cams this why i change pistons as i understand intererance on valve reliefs
Spent the last few weeks hunting for parts but very hard to find anything that dosnt exceed 12.5.1
And extremely grateful for all your knowledge you share
@@jap_adz the YCP gen1 should be low enough that’s around 12.3:1 almost
I have a gsr can I put the b20 block with the gsr head and have no trouble?
Oh nice that will be a bigger “beast” 😅
No trouble with the GSR head check this video of ours for the things u need to do to your gsr head so it is ready for a b20vtec conversion application
Feel free to ask anything on it man
ruclips.net/video/8ERcLeY56Zo/видео.html
Have you ever did a b20v build with those same 13.5 pistons and skunk2 pro1 cams?
No not yet but that would be substantially good on the mid range and torque with a bit of top end
That’s what I suggest the owners
After they max out the CTR cam and eventually beat their currrent 13.5sec time, Pro1 is my next suggestion
Ive build 2018 a B20 Block with Nippon 84.5mm CTR Pistons, with skunk2 pro 2 cams and it made with pump gas and small exhaust 243hp. With bigger exhaust and no catalytic converter it made over 255hp..engine runs till today without problems.
how much for the piston to wall clearance bro using nippon racing?@@EJ2BSeries
Niceeeeeeeeee!
What head did you use@@EJ2BSeries
how much piston to wall clearance using cast ycp piston in this video sir?
Same as stock it’s a stock bore
0.04-0.05mm sir?
more than that, whatever the stock bore is as long as it’s perfectly round and honed that’s good
I see a lot of nonesense locally where they run oversized rings and file it to fit not understanding the whole ring consistency to bore is no longer perfectly round…
plus they also added % more added windage loss
Even Jaspers b20vtec on 1Up cuz it’s stock bore we made sure the bore is “true” and round and not oval, has 0.0025” piston to wall.. thats 0.06mm
since 2018 it’s been running 12.5s and a street car, the full set up is on the video it’s shared
I know some did the exact same set up and made 214whp only and 13.3sec 🤣
must of wanted it the way of the local myth builders
@@SRDmotorsports thank you for your explnation sir, really appreciate for your information
while watching your videos, I think that there is hope for the b20 block to not burst, but we are not that lucky..
hope is good but expenses are real
@@SRDmotorsports so that block guard is reliable in the engine? the cylinders will last? on stock block without dartons that walls are safe for how much power in your exeprience ? rev 8100? max?
@@josephzaja9210 the owner decided on that block guard but if I can choose, I don’t run a block guard it hinders coolant flow sometimes
we build now third time b20.. 13 compresion b16 pilished ported head camcats cams block is honded on 85mm with block guard.. need to dyno it and tune.. but like we now its very risky to rev it up now without dartons and block girdle.. 😅
@@josephzaja9210 watch the latest video the b20 rebuild hehe running since 2018 also but now bent valve but block is still okay…
Btw what are you guys using to tune with?
Did the customer ever dyno the car? What did it make before and after?
No not yet actually the block is still here cuz customer keeps improving plans hehe
What was the main an rod bearings clearance?
Mains we shoot for 0.0015s give or take a thou. And on the rods it’s 0.0018-0.002”
@@SRDmotorsports thanks I’m doing the same build but I going boost what u think of epoxy block guard
@@michealmiller7724 kinda hard to get it right I mean when done right it seems decent,
But also have done a 350whp b20 turbo that runs 12s a street motor no blockguard
@@SRDmotorsports thanks man good information
hello srd! fan of your videos, do these rods clear oem style b20 pistons well?? (thinking of the ycp p73 style 84mm pistons) the SF website says rods won't clear oem pistons but was thinking that might be a smaller bore b18 problem with this connecting rod. thanks for awesome build video
Yeah I believe it should clear 84mm on this one it was fine
@@SRDmotorsports perfect i think i'm going to end up doing the exact same bottom end setup ycp/sf
Oh that’s nice
Love me some b20 vtec builds, my personal favorites , also why H beam and not I beam rods? I know H beam is stronger for boosted applications but heavier, I beam is very strong as well but lighter, I see I beams more fit for an all motor street/track applications
I agree on Hbeam vs Ibeam , just the customer/owner already ordered it hehehe but def agree on that man
@@SRDmotorsports ahhh I see, well the rods won't waste I can tell you that haha still a sweet build
@@StraightOutThaGudda4U hurts my wallet if it was mine hahaha kidding hahah….I’d be tempted to find a t3/t4 just so the rods are at the right place hahaha
@@SRDmotorsports 😂 I would of be thinking the same thing too haha
Hi sir ask lang po b20b phk piston ang gagamitin po na head itr skun 2 valve retainer
Okay
Where can I ship my enging and how much do you charge for work like this to be done. Thanks
We are in the Philippines,
The link to the shop page is in the description and we got a pricelist “pinned” on the wall for most of the common stuff :)
Ok I’ll run the pro 1 as my type r seems limited as of now the pro 1 are 800 right now
Depending manifold yeah I can imagine, as these guys run an Ultra Street so I feel they can squeeze a bit more off it
@@SRDmotorsports same here I’m running ultra right now even thinking of adding skunk2 piston and rod see how compares to my current type r piston rod crank camshaft cam head package replace with all skunk 2. Was told power is not good for amount of money but what’s not lol 😂
@@topshelf223 well it ain’t cheap but power is there
why is the crankshaft area so rusty? is that okay to rebuild an engine on?
What you mean crankshaft area? Can u identify a “time” marker so we can check?
If it’s under the block the brown color is the block having the old oil bed into it (previous owner used old oil too long lol)
But it’s cleaned up good
@@SRDmotorsports at 7:12 like the walls looks rusty, or its the old oil. Btw will you make a vid explaining in depth about head porting diy? Like throat ratios and all that Thx!
@@hox2596 yeah 7:12 is old oil that’s cooked it’s not rust cuz it’s aluminum…
That video might be too long and too hard to make cuz it’s too “generalized” to do so.. example if on. PR3 head the “bowl” oft times does not need to go too big = it’s already big
So in general the throat is more important here
But on a D16 the bowl may be a different story…then if we switch it to another brand like Toyota or Volvo (factor in displacement and piston speed) it goes a little bit different again
What is the purpose of the block guard on the NA application?
Actually…as u mentioned it, we never ran a block guard on Hondas I mean the darton MiD sleeves have it built in so it’s fine
But Honda’s floating system (not closed deck) has proven to be awesome so we don’t usually run a block guard (The 12.5s we did doesn’t use it)
However this block? They built this prior to going to us so we left it as is (they had it all along)
piston brand??
Ycp
@@SRDmotorsports tq
no probs :)
yeeeee
It’s running now owner got the block they retuning alot hopefully means more power
Should’ve been faster in the 1/4 mile. I ran a 13.0 stock block, stock ports just cams and e85 on a base map
yep depends on the track that was a road with timing points mocked up and pump gas
But nice
And it already ran 13.1 on oem cams too
Good day sir, i think i've heard you say you're using a want win adjustable cam gear in one of your build, can you please help me be enlighten? I am also using a want win adjustable cam gear on a sohc engine but upon setting the cam on tdc using the stock cam gear and putting the want win they wont line up perfectly, to be perfectly tdc like the stock cam gear i need to retard the want win a few degree, is this normal?
Yes first of all good Job man!
I think want win has two kinds but unlabeled it could be y series (vti) or z series (p08)
I say this because my want win seems “normal” for my esi engine on esi head which is set like a p08
But a customer has it and it’s off by 4degrees and to find out? U use ur stock camgear and match the “kunya” to where stock is and that is your ZERO
So yeah u can either retard or advance a few deg to match the zero of ur stock camgear
@@SRDmotorsports thank you very much for your fast response, it seems that the want wins tdc mark is advance a little further compared to the stock gear🙂
@@aelaeo yes by how many degrees estimate if u check let me know and there is a continuation of info after that hehe
@@SRDmotorsports i don't exactly know the degree but it was the 1st line retarded from the center of the want win cam gear
@@aelaeo oh just one line so that’s good
That’s ur zero
Sometimes it’s 3-4 lines on the gear so it’s always different
#Underrated #views #likes #subscribe #follow #Support 👌👌
Oh man thank you thank you my brother Rene I appriciate that man!
@@SRDmotorsports best videos yet super informative!👌
@@renesandoval7515 amen brother just sharing the love and will keep sharing indeed as I’ve been lucky to meet a few OG back in the forum days and be actual friends and pass on some goods…we make use of the platform we have now for real