Hello Sir, I am French 🇫🇷 and fortunately RUclips allows you to activate the subtitles of your videos. I understand everything thanks to you! I just started in micro welding and I'm doing well. However, I need some explanations to understand certain phenomena and that's where your explanations are valuable to me. I loved this explanation video. It expands the explanation of one of your videos on replacing a Nintendo Switch charging connector. You said that "you had to change the tip of your soldering iron to suck the tin into the fixing hole of the legs. If the tip is not the right size, the heat ratio will be unbalanced. Even when heating to 1000 degrees, tin will not melt. Therefore, it is impossible to suck it up with the braid to desolder". This allowed me to understand why I had a lot of trouble sucking tin! A big thank you to you because I also appreciate your videos for the quality and clarity of your explanations during your interventions. I would like to see other videos of this type and above all, keep making detailed videos, it's very important! A big thank you for everything! 👍👍👍👍😉😉😉 Ceddine TEL’A’DOM - From France
@@intercepte Non. Je pense que ce n’est pas une question de matière mais plutôt de taille et de chaleur en fonction du support sur lequel tu travaillera et du résulta que tu souhaites obtenir. J’utilise une station SUGON (qui est 2x moins chère qu’une JBC) sur laquelle j’ai la possibilité d’adapter des embouts JBC (environ 50€ la panne). À plus !
@@Chamussu je sais j'ai compris les formes. Mais moi c'est plus l'aspect qualité et utilisation a long terme. la il semble utiliser les mêmes depuis le début donc elle semble très résistante donc la matière et important pour une bonne transmission de chaleur si elle est mal repartie fausse la température de la station et l'embout peux se détérioré rapidement. donc si tu les payes cher faut mieux avoir toutes les informations pour bien choisir.
I find the actually metal quality makes a big difference. I have a Weller original tip that stays shiny and solder wets up against it well. Ali express tips go brown with oxide and need constant wiping and the solder does not wet well. The golden rule. Crap quality equipment gets a crap ending. Thanks. Your a godsend to society
Thanks, this was such an eye opener! As a beginner you are really wondering whether you're dumb or your equipment is trash. If something feels unreasonably difficult or complicated, you're missing something.
I've watched many videos to try to get a good idea which tips I need. This is the most informative video I could find. Thank you for sharing your knowledge.
Heat inercy, big components diffuse the heat so much that the temperature of the tip decreases. Big ones have more inertia and cool slower therefore heat components better. It's like using a big hammer or a small hammer to destroy a wall. Your strength doesn't change but the mass of the hammer makes the difference. Because it can store more energy.
Well explained sir! Thank you so very much for sharing your knowledge with us. Many people don't know how much time it takes to learn how to properly do the job..
Brilliant video! Making use of the thermal cam to show heat spread on the board really gets the point across about choosing right tip for the job in hand. Awesome, TY!
I’m very much an amateur and use amateur equipment but I was advised to use Hakko T18 tips on my cheap station. One tip costs as much as a dozen generic tips, £8-£11 from PiHut, but they are worth it. I found out the quality of the tip is nearly as important as the shape for heat transfer. The main one I use is the T18-D24 which they call a 'screwdriver' tip but it looks like a chisel to me. Then I use T18-K knife tip and a T18-B conical for tight places. These three do 99% of the things I solder and I still have my cheap ones for when needed. Also, instead of using all my tips in the same holder I have separate holders for each tip and change the all lot. It’s quicker, safer as you’re unscrewing plastic not metal and causes less damage trying to get a hot tip out. I tried using a bent tip but my soldering is mainly my simple boards I build for Arduino Nano, ESP32 and Raspberry Picos. As I said, I’m a total amateur and I’m in awe of what you do.
the demonstration with thermal camera is very instructive. I've found out your channel a few days ago and I was watching your last videos... but this old one that was suggested by youtube is very useful. Thankx for sharing
Great video!! Thank you!! I forgot I changed the tip and was getting nowhere recently. Watched this and realised that the slim tip wasn’t conducting enough heat and that’s why my solder wasn’t melting. I spent ages and coolant understand why, thought the slim tip was what I needed for accuracy but no. Thank you!!
I go 85% normal chisel for heat transfer properties. 5% differently bent chisels (sideways etc.) and that 10% is specialty tips like spades (very VERY wide cartridges) or some such weird contraptions... spoon is amazing for drag soldering etc. but 85% chisel and I can do almost anything as long as leads are accessible. Done even some QFN's with basic chisel from Weller WHS-40 consumer soldering station. As long as you have access to the pads and enough flux, you can move mountains... :D
I really only use two tips, bevel and super fine conical, I also have a knife one that came with my iron, it is sometimes useful but mainly the bevel is my main, I use bevel over the chisel because it is sharper on one side but has bigger surface area on the other side, its great, and the fine conical 0.2mm tip is for super fine smd stuff
I was soldering yesterday & after I took a break to calm down, I figured I was using the wrong tip so I'll try soldering today with a better tip for what I'm doing
Thanks for the video. This information is really useful. Not sure if you have mentioned it but for good heat transfer the soldering iron tip needs to have been tinned correctly. I notice that the ones that you use here are all silvery and shiny which indicates the tips have been tinned.
Thank you so much for this video 🙏❤️.... It's really helpful for me to understand soldering 🙏❤️ concept because no one will tell this to me. 🙏🔥 Please make more videos like this 🙏. I'm student From India 🙏
Thanks. Your stuff is always down to earth and good.Really valued the thermal cam It would be great if you could use it on ts100 and other hollow tube soldering irons with changable tips to see difference heat transfer Have got confused by the fact that the hollow tube changeable irons have "large" 65w power supplies (note your Weller is 200W) and yet people say that the heat exchange to the tips is no good, and yet TS100 has 65W power supply. Is the difference really only the fact the heating element/tip are one piece so heat is efficiently transferred. I appreciate you mainly do board repairs. For no lead boards do you need to go to above 400 degrees Some irons say they goto 480 C which is above TS100 400 degrees?
I got the one of older Weller wtcp-s that have magnstat I think it have 1mm tip can't remember the model but I know it heat to 370c. Only replaced the tip over a year ago still have the same soldering station over 15 years it never gave a single issue :)
Thanks for sharing your knowledge and your expirence. Just a quesyion... Any changes or improvement after a couple of years since that you recorded this video ?
Thanks for sharing your knowledge it us 👍 i was having this dilema and this vídeo clarified me. Keep up with the good work and with this fantastic channel 🤜🤛
very much thank you for giving us amazing tips. i really appreciate and always watching you're videos and learned a lot to you sir. thank you so much You're my inspiration
@@allthegearnoidea6752 "The knife soldering iron tip comes with a slanted tip resembling the shape of a knife. It is great for drag soldering and fixing solder bridges. It is not impossible to do point soldering with this tip, but it is considerably difficult as compared to the other tips."
great video! now i understand why i cant desolder such a small component....got so frustrated....becuz the solder melt but not coming off board easily and having hotter tip destroyed component from reuse....Great knowledge!
Thanks for this video bro. Plz tell me how to clean the tip surface.when I clean the tip after letter work tip become black and then not working proper.
I want to get a metal bed frame and want to fill in the crevices. I notice on some metal chairs that something is used to keep the crevices look gone. Any clue what I can use? Love your video ?
awesome video thanks a bunch !! but you didn't explain what all tip types does and when to use them like the bevel tip for instance I wish you 'll answer me as soon as possible or even make a video about it ! i just subscribed to your channel and again thanks anyway!
Hi sir I've watched your vid which was bass on slodering tips I've just order 40 watts and I'm confused about the tip of it I don't know the size of it could please guide me and let me know which size or number of the tip will fit in I would be very grateful to you thank you
Quick question, I want to desolder SMT Capacitors, with a Weller WMRT with Tip T0054465399N which is 3mm wide. What's the height from the Tip to the fatter top part of the Tip? as I'm not sure the Capacitor will be too high for the Tip to touch the Pads
What tips do you recommend for soldering hdmi ports on ps4 & xbox one and also to solder nintendo switch and other charging ports? I have the hakko FX888D soldering station.
Thanks for the really useful video. I have an interesting repair project on my old washing machine that has a few components that have either shorted or need replacing as a possible fix. Not sure if it will fix the problem, but as it's broken already, I'll be chuffed with the stuff learnt here if I get the components replaced and it makes the washing machine work again. :D Rather that, than one of my retro devices that I really don't want to break.
I could listen to this guy all day!
Agreed
Hmm
Me to
This guy is Awesome! the best tutorials about soldering. Straight forward and no mumbo jumbo something like that. Thanks!
That thermal imagery is worth a million words. Tip geometry matters even more than station setting.
Hello Sir,
I am French 🇫🇷 and fortunately RUclips allows you to activate the subtitles of your videos.
I understand everything thanks to you!
I just started in micro welding and I'm doing well.
However, I need some explanations to understand certain phenomena and that's where your explanations are valuable to me.
I loved this explanation video. It expands the explanation of one of your videos on replacing a Nintendo Switch charging connector.
You said that "you had to change the tip of your soldering iron to suck the tin into the fixing hole of the legs. If the tip is not the right size, the heat ratio will be unbalanced. Even when heating to 1000 degrees, tin will not melt. Therefore, it is impossible to suck it up with the braid to desolder".
This allowed me to understand why I had a lot of trouble sucking tin!
A big thank you to you because I also appreciate your videos for the quality and clarity of your explanations during your interventions.
I would like to see other videos of this type and above all, keep making detailed videos, it's very important!
A big thank you for everything!
👍👍👍👍😉😉😉
Ceddine
TEL’A’DOM - From France
tu sais c'est quoi la matiere de ses embouts ?
@@intercepte Non. Je pense que ce n’est pas une question de matière mais plutôt de taille et de chaleur en fonction du support sur lequel tu travaillera et du résulta que tu souhaites obtenir.
J’utilise une station SUGON (qui est 2x moins chère qu’une JBC) sur laquelle j’ai la possibilité d’adapter des embouts JBC (environ 50€ la panne). À plus !
@@Chamussu je sais j'ai compris les formes. Mais moi c'est plus l'aspect qualité et utilisation a long terme. la il semble utiliser les mêmes depuis le début donc elle semble très résistante donc la matière et important pour une bonne transmission de chaleur si elle est mal repartie fausse la température de la station et l'embout peux se détérioré rapidement. donc si tu les payes cher faut mieux avoir toutes les informations pour bien choisir.
@@intercepte oui je te comprends.
I find the actually metal quality makes a big difference. I have a Weller original tip that stays shiny and solder wets up against it well. Ali express tips go brown with oxide and need constant wiping and the solder does not wet well. The golden rule. Crap quality equipment gets a crap ending. Thanks. Your a godsend to society
Thanks, this was such an eye opener! As a beginner you are really wondering whether you're dumb or your equipment is trash. If something feels unreasonably difficult or complicated, you're missing something.
Alham duleilah.. Whatever i needed for my training... My brother helped me.. Marshallah!!!
Sir, I am a beginner. Your video exactly fitted my need. Thanks a lot
I've watched many videos to try to get a good idea which tips I need. This is the most informative video I could find. Thank you for sharing your knowledge.
Thank you. Explained why I can't remove big solder with small tip
Heat inercy, big components diffuse the heat so much that the temperature of the tip decreases.
Big ones have more inertia and cool slower therefore heat components better.
It's like using a big hammer or a small hammer to destroy a wall. Your strength doesn't change but the mass of the hammer makes the difference. Because it can store more energy.
One of the best soldering videos I've come across. Thank You for sharing essential knowledge.
I used the information you shared in this video and my soldering improved one hundred percent. Thank you very much. I greatly appreciate your help!
Well explained sir! Thank you so very much for sharing your knowledge with us. Many people don't know how much time it takes to learn how to properly do the job..
Brilliant video! Making use of the thermal cam to show heat spread on the board really gets the point across about choosing right tip for the job in hand. Awesome, TY!
I’m very much an amateur and use amateur equipment but I was advised to use Hakko T18 tips on my cheap station. One tip costs as much as a dozen generic tips, £8-£11 from PiHut, but they are worth it. I found out the quality of the tip is nearly as important as the shape for heat transfer. The main one I use is the T18-D24 which they call a 'screwdriver' tip but it looks like a chisel to me. Then I use T18-K knife tip and a T18-B conical for tight places. These three do 99% of the things I solder and I still have my cheap ones for when needed. Also, instead of using all my tips in the same holder I have separate holders for each tip and change the all lot. It’s quicker, safer as you’re unscrewing plastic not metal and causes less damage trying to get a hot tip out. I tried using a bent tip but my soldering is mainly my simple boards I build for Arduino Nano, ESP32 and Raspberry Picos. As I said, I’m a total amateur and I’m in awe of what you do.
the demonstration with thermal camera is very instructive. I've found out your channel a few days ago and I was watching your last videos... but this old one that was suggested by youtube is very useful. Thankx for sharing
most informative you tube micro soldering site. brilliant strait forward easy to follow
Great video!! Thank you!! I forgot I changed the tip and was getting nowhere recently. Watched this and realised that the slim tip wasn’t conducting enough heat and that’s why my solder wasn’t melting. I spent ages and coolant understand why, thought the slim tip was what I needed for accuracy but no. Thank you!!
This has to be my favorite soldering video thus far. Thanx man for taking the time to make this video. Much love man.
Thank you this was super helpful!
I’m really enjoying watching your videos and techniques
NICE! Appreciate this video very much! Noob looking for exactly this kind of info and tips! This is huge! Thank you.
So so helpful Alex. Really appreciate it. Thank you from the UK.
I go 85% normal chisel for heat transfer properties. 5% differently bent chisels (sideways etc.) and that 10% is specialty tips like spades (very VERY wide cartridges) or some such weird contraptions... spoon is amazing for drag soldering etc.
but 85% chisel and I can do almost anything as long as leads are accessible. Done even some QFN's with basic chisel from Weller WHS-40 consumer soldering station. As long as you have access to the pads and enough flux, you can move mountains... :D
my eyes have been opened!!! thank youuuuuuuu
expertise is the key to correct repair,great job Alex.
I really only use two tips, bevel and super fine conical, I also have a knife one that came with my iron, it is sometimes useful but mainly the bevel is my main, I use bevel over the chisel because it is sharper on one side but has bigger surface area on the other side, its great, and the fine conical 0.2mm tip is for super fine smd stuff
I was soldering yesterday & after I took a break to calm down, I figured I was using the wrong tip so I'll try soldering today with a better tip for what I'm doing
Thank you so much for the valuable advise and information. I have to practice using different tips and get used to them. Keep well and take care.
This is a really good video on how to use soldering iron tips. Thank you.
I only use bevel and knife tips
Awesome thermal cam footage btw
this video was very informative I learnt a lot thanks very much.
Thanks for the video. This information is really useful. Not sure if you have mentioned it but for good heat transfer the soldering iron tip needs to have been tinned correctly. I notice that the ones that you use here are all silvery and shiny which indicates the tips have been tinned.
Great close up and thermal is excellent touch.
Thank you so much for this video 🙏❤️.... It's really helpful for me to understand soldering 🙏❤️ concept because no one will tell this to me. 🙏🔥
Please make more videos like this 🙏. I'm student From India 🙏
Amazing. I'm just starting soldering. You are my best teacher :) Thx.
Thanks. Your stuff is always down to earth and good.Really valued the thermal cam It would be great if you could use it on ts100 and other hollow tube soldering irons with changable tips to see difference heat transfer Have got confused by the fact that the hollow tube changeable irons have "large" 65w power supplies (note your Weller is 200W) and yet people say that the heat exchange to the tips is no good, and yet TS100 has 65W power supply. Is the difference really only the fact the heating element/tip are one piece so heat is efficiently transferred. I appreciate you mainly do board repairs. For no lead boards do you need to go to above 400 degrees Some irons say they goto 480 C which is above TS100 400 degrees?
Amazing. I’ll surely check my tips tomorrow :)
Deligintly great job Sir..... Thanks v much. 🇧🇭✌️
Thank you for the lesson.
Good stuff... They taught us this in 2M school week one! #Hooyah #Navy
Jus started watching your channel. Good stuff u put out. I learned allot from you. Thanks
I like your work very much you do all you job professionally
Very precise and on-point explanation.
Very educational! Wow I’ve never been schooled like this
Thank you for the advice!
Very well explained 👍
Excellent video, very helpful. Thanks
I got the one of older Weller wtcp-s that have magnstat I think it have 1mm tip can't remember the model but I know it heat to 370c. Only replaced the tip over a year ago still have the same soldering station over 15 years it never gave a single issue :)
Thanks for the time and effort gone into making this video!
Thanks for sharing your knowledge and your expirence. Just a quesyion... Any changes or improvement after a couple of years since that you recorded this video ?
Think I will be re-watching this a few times to imprint it. I have a lot to learn tho I worry about if my hands are steady enough
Thanks for such a thorough explanation!
my hero,greetings from Europe
Very useful tips.
Thank you.
how long have you been repairing, your knowledge is amazing .
Thanks for sharing your knowledge it us 👍 i was having this dilema and this vídeo clarified me. Keep up with the good work and with this fantastic channel 🤜🤛
very much thank you for giving us amazing tips. i really appreciate and always watching you're videos and learned a lot to you sir. thank you so much You're my inspiration
Hi great video. Can I ask what jobs knife tips are designed for. Thanks
This is a fantastic video / thank you for sharing your knowledge
@NorthridgeFix
Can you please make a video about correct way to use hot air, temps, air speeds?
THANKS!
Immensely helpful! Thank you, sir.
I've learned to use the knife tip for everything.
Can I ask what a Knife tip is designed for. I don’t see people using them? Thanks regards Chris
@@allthegearnoidea6752 "The knife soldering iron tip comes with a slanted tip resembling the shape of a knife. It is great for drag soldering and fixing solder bridges. It is not impossible to do point soldering with this tip, but it is considerably difficult as compared to the other tips."
Assalam Alaykom
I really like to thankyou for the knowledge you are giving that really helps, May Allah have mercy on you. JAZAKALLAH
Excellent lesson, thanks👍🏽
great video! now i understand why i cant desolder such a small component....got so frustrated....becuz the solder melt but not coming off board easily and having hotter tip destroyed component from reuse....Great knowledge!
Very helpful. Thanks!
Thanks for this video bro.
Plz tell me how to clean the tip surface.when I clean the tip after letter work tip become black and then not working proper.
The small tip was not as clean a the bigger one. It was pretty black. Whould it do a better job cleaned..?
wonderful, world class video
Words of a master.
How did u change tip so quick??? That's awesome explanation
MUCH LOVE cant stress that enough!
You accent seems very familiar. Very informative video thank you! I live in Turkey btw any relations?
Sir,
very very important information.
However, how to keep the iron tip Clean and tidy?
Hello sir i am your biggest fan
dont u usually put give small amount of tin on the tip to increase contact area?
Thanks for important work you do 👌
Question, for hdmi port like ps4 and 5 or laptop, can i have to mix low temperature soldering wire to can remove the port ? thx Ali
I watched the whole advertisement and ill share this all over👌👌👌
I want to get a metal bed frame and want to fill in the crevices. I notice on some metal chairs that something is used to keep the crevices look gone. Any clue what I can use? Love your video ?
What tip I should be using to solder TSSOP28 IC component ? Pitch size 0.65mm. I am looking at t12 tips.
Talking about: Just the tip.
Are using T12 soldering iron?
Thanks for video, where can I get good tips. My tips get so brittle after few uses. My station is set at 480°
awesome video thanks a bunch !! but you didn't explain what all tip types does and when to use them like the bevel tip for instance
I wish you 'll answer me as soon as possible or even make a video about it !
i just subscribed to your channel and again thanks anyway!
Could you please tell me which tips to order for the weller
It is certainly an art.
which fLIR camera did you use to make this video?
Can I ask what a knife tip is used for. My JBC micro station came with one and I have no idea what it’s designed for ?
Good information! thanks!
Great video. Any ideas on unsoldering guitar pickup covers?
thank you. this a really good video. thanks.
Hi sir I've watched your vid which was bass on slodering tips I've just order 40 watts and I'm confused about the tip of it I don't know the size of it could please guide me and let me know which size or number of the tip will fit in I would be very grateful to you thank you
Here I been using wrong tip for the well 1010NA I'll switch it up when I have to go for very small components.
Quick question, I want to desolder SMT Capacitors, with a Weller WMRT with Tip T0054465399N which is 3mm wide. What's the height from the Tip to the fatter top part of the Tip? as I'm not sure the Capacitor will be too high for the Tip to touch the Pads
What tips do you recommend for soldering hdmi ports on ps4 & xbox one and also to solder nintendo switch and other charging ports? I have the hakko FX888D soldering station.
THANK YOU AGAIN FOR THESE VIDEO
الله يعطيك العافية
Thanks for the really useful video. I have an interesting repair project on my old washing machine that has a few components that have either shorted or need replacing as a possible fix. Not sure if it will fix the problem, but as it's broken already, I'll be chuffed with the stuff learnt here if I get the components replaced and it makes the washing machine work again. :D
Rather that, than one of my retro devices that I really don't want to break.