Thank you so much. I fixed my mirror in less than 10 minutes. The collision center wanted to charge $750. The tool needed to not crush the wires is an oxygen sensor socket and can be purchased or rented from Auto Zone or any store that sells auto supplies.
Did this a few years ago on my drivers side using a pipe wrench, but barely tweaked the nut. Now both mirrors are flopping and I’ll be following your instructions exactly. Thanks so much!😊
DUDE!!! Thanks for the lesson. Someone hit my girlfriends mirror yesterday... She wanted to buy one ASAP! TOLD HER WAIT!!! Found your video! SWEET! Can't wait to fix it later on today! -Honest²
YOu sir have made my night. I was upset because kansas city was losing in the 1st quarter and I could not get this mirror fixed. Lexus was trying to charge me $515. I was like go ahead and order it. Then I watched several videos but then I got to yours. The most simplest easiest quickest fix out of all that I've seen. Some guys will pull in the wires all the way out taking the door panel a loose no illuse I must give you credit yours is the best. And we thank you. My wife loves me because of this lol and the Kansas City Chiefs are now winning 23 to 24
Augusta ga My wife drove through the car wash and the flaps Messed up the mirror appearance Alexis Lexus say that the total will be 515.00. I started to buy it after watching 2 other videos did it was a way too much work for me and what I want to do. Then I saw this video. Thank you sir and thank GOD for you tube.
My SC 300 mirror was repaired twice before, and the tube was mangled. What I did was put a long thin bolt down the center of the tube (with a small washer on top), right next to the wires. On the bottom of the support, I put a washer and nut to tighten the spring down. I used a weaker spring. This will never fail again!!!!
Really helpful video. Thanks for posting. A few additional comments/tips for doing this job: * removing mirror: clarifying for viewers that there are two plastic tab/slots at the top and two plastic clips on the bottom, so be sure to only pull outwards from the bottom * screws: as far as I could tell, you only need to remove three screws, not four. The lower right one (which gave me a LOT of trouble due to corrosion) doesn't seem to hold the back of the enclosure on at all. * After hammering the ring back into position as described, I added a small hose clamp onto the post above it. Maybe a little insurance against it ever happening again. * In the While You're There department, check the running light bulb before you put everything back together again.
@@pmrdoctor6429 same here, I think the parts sticking out of the post was worn out too much over time and there's not much for the washer to hang on to
Gracias hermano por tu video ( me pasó lo mismo y vi tu video y así lo hice y me funcionó, gracias por todo ( cómo decimos los cubano here’s un bárbaro) , gracias hermano
This was not as easy to press down on the spring for me. Mine had A LOT of tension and I had to put a lot of body weight on it to get the spring to go down. I watched this video 10 times and spent 3 hours to get the spring in and put the housing back.
great video , quick question i cracked the glass i see i can order new glass, but also on the motor there are 3 plastic clips holding it in 2 are broken, is there a way to replace those? the motor works fine??
I followed the video however when finished the mirror doesn’t go forward or back like if pushed hard like used to and passenger mirror. Did I do something wrong?
Sweet job! Wondering if this trick will work on 2008 GS? I want to basically replace the mirror glass only without having to remove the entire housing! Thanks!
I’m I have a 2017 Lexus NX200t and when I removed the glass their aren’t screws. So I can’t figure out how to separate the housing to get to the shaft. HELP!
Do a vid for Ls430 2001-2003..cant find anything out there and the setup inside is shrouded in plastic and cant get to the spring smh, someone help plzzzzz
Exactly same issue not holding on. I am thinking of using metal putty to see if it will hold onto the post and then try to press the clip in. Don’t know if this will work
Push it down slow and it takes a lot more pressure than you'd think it should. Don't just hit it the first time, pus it down until it catches then tap it on down farther. Good luck
@@wildjc1yeah I did this fix and it worked but when I drove after it broke again. Do you have a fix do I have to hit it harder or just use tape like I have been? Help😂
The Lexus dealership just told me it could cost $150 or I might need a new mirror which costs $1000 to replace and they won’t know for sure until they open it up which is the $150 and if the whole thing needs replacing the $150 is non refundable. Both my mirrors are loose lmao!
Thank you so much. I fixed my mirror in less than 10 minutes. The collision center wanted to charge $750. The tool needed to not crush the wires is an oxygen sensor socket and can be purchased or rented from Auto Zone or any store that sells auto supplies.
I did it myself with an oxygen sensor socket.
how? and did you make a video by any chance?
I just fixed mine in 12 minutes they charged me $350 it's crazy thanks to your video
This 100% helped me fix both of my Lexus side mirrors in less than 1 hour. I ended up using a pipe wrench and rubber mallet! Thank you!
Did this a few years ago on my drivers side using a pipe wrench, but barely tweaked the nut. Now both mirrors are flopping and I’ll be following your instructions exactly. Thanks so much!😊
Thank you for the great tip, fixed this same problem for the cost of the socket. Much appreciated!
DUDE!!! Thanks for the lesson.
Someone hit my girlfriends mirror yesterday... She wanted to buy one ASAP!
TOLD HER WAIT!!! Found your video! SWEET! Can't wait to fix it later on today!
-Honest²
YOu sir have made my night.
I was upset because kansas city was losing in the 1st quarter and I could not get this mirror fixed. Lexus was trying to charge me $515. I was like go ahead and order it. Then I watched several videos but then I got to yours. The most simplest easiest quickest fix out of all that I've seen. Some guys will pull in the wires all the way out taking the door panel a loose no illuse I must give you credit yours is the best. And we thank you. My wife loves me because of this lol and the Kansas City Chiefs are now winning 23 to 24
Fixed my ES350 mirror in 60 seconds with this video. Thank you!
Augusta ga
My wife drove through the car wash and the flaps Messed up the mirror appearance Alexis Lexus say that the total will be 515.00.
I started to buy it after watching 2 other videos did it was a way too much work for me and what I want to do. Then I saw this video.
Thank you sir and thank GOD for you tube.
My SC 300 mirror was repaired twice before, and the tube was mangled. What I did was put a long thin bolt down the center of the tube (with a small washer on top), right next to the wires. On the bottom of the support, I put a washer and nut to tighten the spring down. I used a weaker spring. This will never fail again!!!!
Thank you for the oxygen sensor part. I was worried about damaging the wires.
Thanks for this video, I was able to get it done with a basic wrench and rubber mallet!
Really helpful video. Thanks for posting. A few additional comments/tips for doing this job:
* removing mirror: clarifying for viewers that there are two plastic tab/slots at the top and two plastic clips on the bottom, so be sure to only pull outwards from the bottom
* screws: as far as I could tell, you only need to remove three screws, not four. The lower right one (which gave me a LOT of trouble due to corrosion) doesn't seem to hold the back of the enclosure on at all.
* After hammering the ring back into position as described, I added a small hose clamp onto the post above it. Maybe a little insurance against it ever happening again.
* In the While You're There department, check the running light bulb before you put everything back together again.
The post on mine is too small and narrow for the clip to hold on. I don’t know how you guys were able to do it
@@pmrdoctor6429 same here, I think the parts sticking out of the post was worn out too much over time and there's not much for the washer to hang on to
This worked like a charm. Saved me so much money! Thanks!
Great tips and video guide, fixed my is350c mirror!
Great video, I need to change the mirror glass on my 3IS so thank you!
Thanks for the quick fix!
Fixed my right… then my left broke a few months later so here I am 😂
Gracias hermano por tu video ( me pasó lo mismo y vi tu video y así lo hice y me funcionó, gracias por todo ( cómo decimos los cubano here’s un bárbaro) , gracias hermano
This was not as easy to press down on the spring for me. Mine had A LOT of tension and I had to put a lot of body weight on it to get the spring to go down. I watched this video 10 times and spent 3 hours to get the spring in and put the housing back.
great video , quick question i cracked the glass i see i can order new glass, but also on the motor there are 3 plastic clips holding it in 2 are broken, is there a way to replace those? the motor works fine??
you are awesome! I was about to buy the mirror!
I followed the video however when finished the mirror doesn’t go forward or back like if pushed hard like used to and passenger mirror. Did I do something wrong?
Sweet job! Wondering if this trick will work on 2008 GS? I want to basically replace the mirror glass only without having to remove the entire housing!
Thanks!
What size oxygen sensor did he use.
Thanks you!! My LS has this problem.
I just did this and now my Sideview wont collapse. Was something not aligned when i hammered it? No clue how to take it back off
What size socket should be used?
How do you clip the mirror back on?
What if we don’t have an oxygen sensor
How do I put the mirror back on😂
Does it matter what wire goes where for your defrost? There's a brown and green wire. And I dont know which one goes where.
Might not matter since it's just for defrost, but on mine (2010 ED) brown wire on top, red on bottom.
Could not fix mine as the clip is too small for the post
Which way does the glass pop off? Mine isn't coming off as easy as the video makes it seem.
@David • i couldnt locate them? Im trying to find it for a 2016 IS 300
@David • no unfortunately not. The closest one to me is 4.5hr away.. i guess i could call one tho not a bad idea
I’m I have a 2017 Lexus NX200t and when I removed the glass their aren’t screws. So I can’t figure out how to separate the housing to get to the shaft. HELP!
If you hit the washer too hard, it will fix the problem but you will not be able to swivel the mirror.
What I really need!!! Thank you SIRRRR!!!!
Thank you so much, greatly appreciated.
Do a vid for Ls430 2001-2003..cant find anything out there and the setup inside is shrouded in plastic and cant get to the spring smh, someone help plzzzzz
Great video! What size oxygen sensor socket?
🤣
@@mattlopez5418 whats funny ? Lol I was gona ask the same question 😂
But when you do this does the mirror still fold inward? Or it’s stuck in that position you put it in?
Mirror will function as new
👏👏👏👏 perfect 👌 Thank you Thank you
Great video. But how do you put the actual glass piece back into place?
Late reply but Top clips go on first then push in bottom clips till you hear click.
HUGE THANKS!
What size is the OXYGEN SENSOR TOOL
thanks
Mi auto en ese resorte lleva una funda, hasta ahí me quedo :( is200t 2016
👍 Liked
I'm having the problem that the ring clip isn't grabbing onto the shaft. I've tried bending the prongs in more but still no luck. What should I do?
I’m having the same issue waste of my time tbh
Exactly same issue not holding on. I am thinking of using metal putty to see if it will hold onto the post and then try to press the clip in. Don’t know if this will work
Push it down slow and it takes a lot more pressure than you'd think it should. Don't just hit it the first time, pus it down until it catches then tap it on down farther. Good luck
same here, the ring on the shaft has worn out on my car and the washer cannot grab on to it.
@@wildjc1yeah I did this fix and it worked but when I drove after it broke again. Do you have a fix do I have to hit it harder or just use tape like I have been? Help😂
Don't hammer it to much otherwise u will not be able to hand turn the mirror after everything is back.
The Lexus dealership just told me it could cost $150 or I might need a new mirror which costs $1000 to replace and they won’t know for sure until they open it up which is the $150 and if the whole thing needs replacing the $150 is non refundable. Both my mirrors are loose lmao!
thats how they make money
Lexus IS pretty crappy. Never buying their cars again
Same process for a Lexus HS 250H?
Not fun
?
yup
just broke my mirror..
SLATTTTT LETS GO!!!
Homie needs to learn how to use power tools.
/ 300 400 for that fix ?wow lol
Who else is struggling taking the fuking mirror off