@@ApocalypticFTW1776 That may help, but after 5 years of working on a range, I seriously doubt it. Let's be honest, most people who are gonna buy this are just gonna mag dump into a perm anyway.
I am a retired firearms/unified tactics/rapid deployment instructor for a large Sheriffs Office. Some of your theories hold water but some are a little too broad in scope. My Department had all the major ammo manufacturers out at our range. We did gel, Sheetrock and various other ballistic testing. We found that the Winchester Silver tip 9mm 124 grain hollow point were the best for human targets. Yes, we tested .45, 10mm, .40, .380, .357 etc etc. The problem children of the group was 9 pellet double 00 buck and .45 acp. They both penetrated over 13 complete sheet rock walls. .223 broke up within 2 double sided walls. My point is this, there is no such thing as “shocking or knock down power”. We found that no matter the caliber, shot placement was key (obviously). Shot placement should always be in the “CNS” or central nervous system. Tip of the nose to the belly button in a straight line. The triangle of the eyes and chin is best. We trained to hit those areas. What I always told my fellow Deputies was this. “Aim small”, “miss small”. Don’t aim at a “person”, aim at the top button of their shirt, tip of the nose etc etc. you’ll be surprised how natural point of aim can be so accurate.
Having quite literally watched as a Glock 17 discharged into my chest, at contact range, as in against my cheat, and my body absorbing every single ounce of energy as the bullet came to a complete stop, within me, I can tell you for a fact, that despite it being a 125 grains speer gold dot, +p, I did not move at all from that muzzle. Though it did do a good amount of damage within me.
I still think this system would absolutely SHINE in one of the chassis systems, particularly in the Meta or the P-iX. Having their binary system in my PTR, and also not owning a single Glock, I don't have a reason to acquire one of these, but I can see these being pretty popular.
They can screech all they want, but after the bump stock and FRT bans just got struck down there's not a lot they can do about it short of passing new federal legislation no matter who the next president puts in charge of the ATF
@@TheLastSaneAmericanlotta good the nfa is doing keeping honest ppl honest i call it the list of criminals and thug’s favorite and most popular weapons cause their the only ones that have them now
I reccomend using a steel guide rod for all the folks planning on using this for fast shooting training, the excessive heat build up can melt your stock plastic rod, its just very thin and heat builds up around it fast.
Linked to GB guns and saw the GP with this product installed. Going to read about it now. That platform,I just might be able to get on board with .Should make for some very short yet fun range trips. The dust from the gravel road entrance at the out door range I go to,when I do go to a range,has usually settled before I’m heading back out.With one of these FA/GP setups,have a feeling my truck is gonna get some of my own entrance dust on it while exiting..Gotta read it ,but with enough training ,that combo could probably have some real life benefits in certain situations.These are the days .A lot of variety for sure!Have a good one.
Good vid. Its an excellent tool. Like any tool you have to be adebt using it. With the right ammo it would be something id use for charging bear. The extra shot or two could be just enough to save your rear. And its fun.
For a unique slide and trigger combo you can't get anywhere else? I bought a stopped frame and basic parts for about 125, to total this is under a grand.
I'm being really picky, but I hate the huge "Franklin Armory" billboard on the side. Other than that, It does seem to be well thought out. I like the indicator on the back of the slide. Its great that it is optic ready. Honestly, my opinion is that if a person is going all in on a build like this, you might as well spend the extra $250-300 on a tax stamp and engraving, so you had the option to put a stock on it.
@@XuroX. It's as close to a G-18 as you are going to get legally. Unless you know someone with a gun dealership that some how got one of the few G-18's in the United States. Only dealer samples were allowed to be imported. So yes really it is. I'm not even considering the ignorant masses of a certain demographic that owns illegally converted weapons with their " Glock switches". I like my freedom too much. So it is as close as you can get without becoming a felon.
@@mikeh.753 2nd half of this statement is pretty offensive wording wise. But gun conversation wise im definitely intrigued in mastery of this set up as a potentially feasible carrying defense against the switch epidemic that is indeed plaguing the streets. Legal, not many recorded vids
@@AWFMEMPHIS first of all- that wasn’t offensive. But most importantly, my best advice would be to not carry an automatic or binary gun. When you need a gun for self defense, you don’t want to mag dump. You want to be able to conserve your ammo and make accurate shots. That keeps you in the fight for longer and limits potential danger to bystanders. A switch isn’t useful in 99% of self defense scenarios- it’s only useful for assassinations or ambushes.
Cool thing to have for ppl who have the disposable income,like you mentioned..Not something that interests me personally (at this time,no matter the cost or amount of money I have/don’t have.Or any Glock,for that matter rather have more ammo to shoot in some of my other guns )BUT,keeping an open mind..As always. Thanks for sharing us different things that are on the market though. Take care GB. PS. Saw the OG Dangers tour of the AR manufacturing plant & the really nice guns that they make that you were visiting that same day. One where that lady put the heat to a PSA AR that OG already had & swapped out the barrel for one of theres. The 2Kish AR that’s supposedly relatively light weight and,if someone purchases one,you have the option to have it upgraded with any new & improved parts,for life for free …That gun appears to have a lot of thought/engineering involved in its creation. Going to be looking into that one deeper. Try & find a dealer and get one in hand. Respect & value all of your knowledge and experience…Also OG’s. Take care and keep up the good work G.
Or you could look at it as: For the price you're paying for R&D, unique parts, a unique trigger and slide assembly for a little more than the price a quality slide was a few years ago.
Awesome informational video. Franklin Armory is a quality manufacturer. The binary trigger kit is definitely not inexpensive,, however it's a legal way to rapidly fire your Glock 17. Surprised Glock has never offered a stock binary pistol. Great shooting, 😄👌. You'll need to obtain some 24 round Glock magazines 😄 You and Toya have a great weekend 😄🙏
@@drerod89 no, still banned: “Trigger modifier”, any modification that repeatedly activates the trigger of a firearm, including, but not limited to, trigger cranks, binary triggers and hellfire triggers.
@@LJR_LIMITED That's the new law right? I remember reading the legislature site about a year ago, and bump stocks, and trigger cranks were mentioned by name, but I don't remember seeing binary triggers specifically
the two rounds in the pairs diverge more than I expected...but it's still accurate enough to have some utility Will there be a future where this capability becomes a common factory feature? I wouldn't think it would be inherently much more expensive
A lot of people don't know that the Glock 17 and the Glock 18 have a slightly different frame. Apparently, the Glock 18 has longer rails for more reinforcement. I think this kit should be tested and one of the "shoot it until it breaks meltdown videos."
For that I'm afraid you'll have to wait for one of the paid/sponsored videos by the channels that make videos for a living. I'm unpaid and have a real job so I have neither the time nor funding for such a thing.
Be wary of Franklin Armory QC or Ruger QC? I have a PC Charger too and considered the FA binary, I’m not on it for the price they want for it at FA though. Soon enough the market will be flooded with low quality lesser known manufacturers overseas and high quality well known manufacturers in the U.S., both copying the FA Binary’s design then tweaking design or materials to loophole the patent. I’d expect the high quality binaries to drive FA’s price down far af, similar to Geissele’s triggers dropping in price or losing market share with the release of the Larue MBT for $100. And the low quality binaries will drive the price of the high quality binaries down at the same time, hopefully. I got burnt on the Geissele triggers for $300-$400 before the Larue MBT came out and am not biting that bait ever again. I still love the Geissele’s but only at the $200 max price point. Any more than that and I default to Larue’s MBT trigger for $100.
Very cool. Love the selector. Having a giant "Franklin Armory" badge with Ben Franklin's profile? on the side ruins it. Thank God they didn't paint the lettering white.
@GBGuns I just don't like large badging on anything. Takes away from the gun imo. Same reason I won't buy a stribog. I just don't want or need my guns to be walking billboards for the company.
Awesome, however.. I live in the suburbs and my local gun range doesn’t allow rapid fire. I really wish I had a bunch of land to shoot whenever I wanted. Unfortunately we have a DEI boarder czar making everything insanely expensive
Honestly I'm surprised it took then this long to come up with the idea, I always thought it was a no-brainer. With stuff like this on the legal market in most states there's no reason for anyone to risk a felony by getting a Glock switch.
Got a oddball question. I have a g34 sbr but cant find out that if you have the franklin trigger in it, can another slide be put on and work as a normal glock and then switch back to the binary slide when you want to use it that way? just something iv wondered, would be kinda a pain to have to swap out the trigger and slide to go back to a longer set up for hunting and stuff.
@@caveymoley Its something iv wondered about, I even tried asking franklin armory but no response, and not been able to get an answer from anyone that had one sadly.
@@lukeabram1674 seriously and the slides aren’t even appealing anyone who buys this is basically promoting them for free wiyh the big ass engraved Franklin armory name in the slide looks like garage to me if I had $800 to waste on it I still wouldn’t just for that reason
Not that I have $$$$. Laying around to buy the conversion, but I’m concerned that the switch would prevent successfully mounting an optic as they all overhang the sides. The switch looks to go above the plate that Franklin included for aesthetics.
If on binary if the last burst is one round, is there any saftey feature besides having to put it on single, if not after one shot and a reload driving the mag into the gun, if the finger isnt holding the trigger will it go off when the slide is forward, can you demonstrate that, showing the results?
I love bump firing my ars and keltec s2000 carbine and verious other xarbines. Its a gas man. To have a glock with this capability is the best. I can bump fire pistols but this really looks too cool. How much?
It’s cool but if you ever gotta use it for defensive purpose, when the cops show up, it’s getting confiscated I prefer guns I can afford to replace without spending half a pay check..
@@mimzy4319no he’s just a smart individual unlike you you lack common sense and brains why would I pay $800 for a binary system when I could get a 3d printer and print out switches for 1/4 of the price ?
Unique slide required for a unique trigger, patented, this is jot as inexpensive to make as a regular slide or trigger, plus it was designed instead of simply copying.
@@GBGuns Respectfully, it’s just a gimmicky tool for people to make noise and show off. And quiet possibly cause injury or death to an inadequately trained kid, or adult. I’ve on occasion shot the 18C and I must admit it definitely put a smile on my face. I mean you no disrespect at all sir.
Full Review: www.gbgunsdepot.com/post/franklin-armory-binary-triggers-glock-17-and-grand-power-stribog-tested
RIP to the ceiling, baffles and target runners at indoor and outdoor ranges. Glad that’s not my problem anymore 🤣
Haha, I worked at one too for a while
Ah those poor ceiling tiles
Lots of hanger hits coming 😂
This man speaks truths
@@ApocalypticFTW1776 That may help, but after 5 years of working on a range, I seriously doubt it. Let's be honest, most people who are gonna buy this are just gonna mag dump into a perm anyway.
This changes the game for the glock SBR kits.
👀DUDE!🤫🤫🤫🤫🤫🤫
@@kingzb3 maybe if it was reliable
@@BamBlamboTv is it not>?
Seemed like nice guys over there when I called and needed an xtra spring. Hopefully they sell a million of these.
I am a retired firearms/unified tactics/rapid deployment instructor for a large Sheriffs Office. Some of your theories hold water but some are a little too broad in scope. My Department had all the major ammo manufacturers out at our range. We did gel, Sheetrock and various other ballistic testing. We found that the Winchester Silver tip 9mm 124 grain hollow point were the best for human targets. Yes, we tested .45, 10mm, .40, .380, .357 etc etc. The problem children of the group was 9 pellet double 00 buck and .45 acp. They both penetrated over 13 complete sheet rock walls. .223 broke up within 2 double sided walls.
My point is this, there is no such thing as “shocking or knock down power”. We found that no matter the caliber, shot placement was key (obviously). Shot placement should always be in the “CNS” or central nervous system. Tip of the nose to the belly button in a straight line. The triangle of the eyes and chin is best. We trained to hit those areas.
What I always told my fellow Deputies was this. “Aim small”, “miss small”. Don’t aim at a “person”, aim at the top button of their shirt, tip of the nose etc etc. you’ll be surprised how natural point of aim can be so accurate.
Having quite literally watched as a Glock 17 discharged into my chest, at contact range, as in against my cheat, and my body absorbing every single ounce of energy as the bullet came to a complete stop, within me, I can tell you for a fact, that despite it being a 125 grains speer gold dot, +p, I did not move at all from that muzzle.
Though it did do a good amount of damage within me.
I still think this system would absolutely SHINE in one of the chassis systems, particularly in the Meta or the P-iX. Having their binary system in my PTR, and also not owning a single Glock, I don't have a reason to acquire one of these, but I can see these being pretty popular.
That's basically what I did, gflex, comp, and reflex 20/20 chassis it's so sweet.
I can’t get my gflex to work in my meta tactical chassis
@@generousghibli6031 it would be nice if it was reliable
That in a carbine kit would be sexy
I was thinking the same thing! I have a few of them but I would be most excited to use it on my Meta Tactical Apex bull-pup conversion kit
@@Mountain_Man that was the exact one I was thinking of....nice 👍🏼
I doubt you'd be able to because of the selector on the slide.
@@InvidiousIgnoramus yeah good point might have to mod it maybe
Honestly for that money you might as well slap a Binary trigger in an AKV, ARV, EP9, etc.
I can already hear the gun grabber conniption fits.
Machine gun, everything that isn’t a musket is a machine gun somehow.
Also machine guns are somehow not arms. lol
They can screech all they want, but after the bump stock and FRT bans just got struck down there's not a lot they can do about it short of passing new federal legislation no matter who the next president puts in charge of the ATF
@@TheLastSaneAmericanlotta good the nfa is doing keeping honest ppl honest i call it the list of criminals and thug’s favorite and most popular weapons cause their the only ones that have them now
Its got a fully semiautomatic 30 clip caliberzine 😂😂
@@TheLastSaneAmerican i love how they made the nfa and just basically asked the criminals to follow their bs laws 😭 lotta good thats been doing
Smiles after the first mag. That looked fairly controllable.
I love it. I'm glad we are this point.
I reccomend using a steel guide rod for all the folks planning on using this for fast shooting training, the excessive heat build up can melt your stock plastic rod, its just very thin and heat builds up around it fast.
This would be an awesome candidate for a radian ramjet!
Linked to GB guns and saw the GP with this product installed. Going to read about it now. That platform,I just might be able to get on board with .Should make for some very short yet fun range trips. The dust from the gravel road entrance at the out door range I go to,when I do go to a range,has usually settled before I’m heading back out.With one of these FA/GP setups,have a feeling my truck is gonna get some of my own entrance dust on it while exiting..Gotta read it ,but with enough training ,that combo could probably have some real life benefits in certain situations.These are the days .A lot of variety for sure!Have a good one.
Yes, with as controllable as a Stribog is, it's an excellent combination. I have a video on that too coming Saturday.
Lol laughed my ass off after that first mag dump for some reason caught me off guard
Just bevause I don't typically run triggers quickly doesn't mean I can't, it's just not normally part of a review
Good vid. Its an excellent tool. Like any tool you have to be adebt using it. With the right ammo it would be something id use for charging bear. The extra shot or two could be just enough to save your rear. And its fun.
800 is nuts.
For a unique slide and trigger combo you can't get anywhere else? I bought a stopped frame and basic parts for about 125, to total this is under a grand.
@@GBGuns what all parts are needed? I’d prefer not to buy a whole nother Glock just to replace the slide
@@mitchellwatters3714 Stripped frames are around 75, then you'll need a frame completion kit (also chearp) barrel (Mine was 50) and a recoil assembly.
This nifty kit is going to be very popular in Chicago.
Nah, those future doctors and scholars use Chinese glock switches.
Nah. These are legal.
The kits are a lot more expensive than a switch
They buy real fully auto switches for around $50 for 20 of them on Amazon and even less on the black market vs $900 for the binary.
Dude, Amazon doesn't sell Glock switches
I'm being really picky, but I hate the huge "Franklin Armory" billboard on the side. Other than that, It does seem to be well thought out. I like the indicator on the back of the slide. Its great that it is optic ready. Honestly, my opinion is that if a person is going all in on a build like this, you might as well spend the extra $250-300 on a tax stamp and engraving, so you had the option to put a stock on it.
Or a micro roni type setup
just fill with jb weld and sand/paint it.
I feel you
This is a legal G-18 for the masses.
Not really
@@XuroX. It's as close to a G-18 as you are going to get legally. Unless you know someone with a gun dealership that some how got one of the few G-18's in the United States. Only dealer samples were allowed to be imported. So yes really it is. I'm not even considering the ignorant masses of a certain demographic that owns illegally converted weapons with their " Glock switches". I like my freedom too much. So it is as close as you can get without becoming a felon.
@@mikeh.753 2nd half of this statement is pretty offensive wording wise. But gun conversation wise im definitely intrigued in mastery of this set up as a potentially feasible carrying defense against the switch epidemic that is indeed plaguing the streets. Legal, not many recorded vids
@@AWFMEMPHIS "2nd half of this statement is pretty offensive wording wise" How exactly? It's just the truth.
@@AWFMEMPHIS first of all- that wasn’t offensive.
But most importantly, my best advice would be to not carry an automatic or binary gun. When you need a gun for self defense, you don’t want to mag dump. You want to be able to conserve your ammo and make accurate shots. That keeps you in the fight for longer and limits potential danger to bystanders. A switch isn’t useful in 99% of self defense scenarios- it’s only useful for assassinations or ambushes.
ATF is pissed
Cool thing to have for ppl who have the disposable income,like you mentioned..Not something that interests me personally (at this time,no matter the cost or amount of money I have/don’t have.Or any Glock,for that matter rather have more ammo to shoot in some of my other guns )BUT,keeping an open mind..As always. Thanks for sharing us different things that are on the market though. Take care GB.
PS. Saw the OG Dangers tour of the AR manufacturing plant & the really nice guns that they make that you were visiting that same day. One where that lady put the heat to a PSA AR that OG already had & swapped out the barrel for one of theres. The 2Kish AR that’s supposedly relatively light weight and,if someone purchases one,you have the option to have it upgraded with any new & improved parts,for life for free …That gun appears to have a lot of thought/engineering involved in its creation. Going to be looking into that one deeper. Try & find a dealer and get one in hand. Respect & value all of your knowledge and experience…Also OG’s. Take care and keep up the good work G.
for the price they charge, a barrel and rod should come with it
Or you could look at it as: For the price you're paying for R&D, unique parts, a unique trigger and slide assembly for a little more than the price a quality slide was a few years ago.
For the price they charge a whole gun should come with it lol
Awesome informational video. Franklin Armory is a quality manufacturer. The binary trigger kit is definitely not inexpensive,, however it's a legal way to rapidly fire your Glock 17.
Surprised Glock has never offered a stock binary pistol.
Great shooting, 😄👌. You'll need to obtain some 24 round Glock magazines 😄
You and Toya have a great weekend 😄🙏
*33 round Glock magazines
this makes way more sense than the G Flex which is binary only. The ability to switch between semi and binary is an awesome tool to have
Gflex doesn't even function half the time on stock glocks and 0% on clones even under ideal tolerances.
G flex is awesome! I love it and it’s cheaper
This in a chassis system would be golden.
The rubber band was broken on mine. Watched the video and reassembly was pretty easy.
love it.. glock 18 without paperwork
Illegal in CA, CT, DC, DE, FL, HI, IA, IL, MA, MD, NJ, NY, RI, and WA
California :(
All democrat run comrade states
I think binaries are legal in MA. That might've changed with the new law they put in place last month
@@drerod89 no, still banned: “Trigger modifier”, any modification that repeatedly activates the trigger of a firearm, including, but not limited to, trigger cranks, binary triggers and hellfire triggers.
@@LJR_LIMITED That's the new law right? I remember reading the legislature site about a year ago, and bump stocks, and trigger cranks were mentioned by name, but I don't remember seeing binary triggers specifically
$899.00 at the website 😳
Save $90
Terrible price honestly.
Not even a good modification for that price either.
Just print a switch
Not even a barrel or recoil assembly. They making a helluva come up .. I doubt anyone fr buying this tho
its like 300 bucks on PSA
the two rounds in the pairs diverge more than I expected...but it's still accurate enough to have some utility
Will there be a future where this capability becomes a common factory feature? I wouldn't think it would be inherently much more expensive
Love it. Well done
Interesting, but I'm not a spray bullets dude. I do love the Glock platform though
I thought I demonstrated well enought aht you can run this as quickly or slowly as you like.
Looks like a great upgrade for the Glock 17 gen 3. But that price is way above anything that I can justify.
I would put a 960 Rowling conversion kit on it.
Missed opportunity to make the serrations compatible with mcks
Great job I agree with you
A lot of people don't know that the Glock 17 and the Glock 18 have a slightly different frame. Apparently, the Glock 18 has longer rails for more reinforcement. I think this kit should be tested and one of the "shoot it until it breaks meltdown videos."
For that I'm afraid you'll have to wait for one of the paid/sponsored videos by the channels that make videos for a living. I'm unpaid and have a real job so I have neither the time nor funding for such a thing.
Super Cool!
ported slide and barrel may work better!
Their binary trigger didn't work in my PC Charger. Sent them the gun, got it back minus their parts & a full refund. They blamed Ruger. Be wary of QC
Be wary of Franklin Armory QC or Ruger QC? I have a PC Charger too and considered the FA binary, I’m not on it for the price they want for it at FA though. Soon enough the market will be flooded with low quality lesser known manufacturers overseas and high quality well known manufacturers in the U.S., both copying the FA Binary’s design then tweaking design or materials to loophole the patent. I’d expect the high quality binaries to drive FA’s price down far af, similar to Geissele’s triggers dropping in price or losing market share with the release of the Larue MBT for $100. And the low quality binaries will drive the price of the high quality binaries down at the same time, hopefully.
I got burnt on the Geissele triggers for $300-$400 before the Larue MBT came out and am not biting that bait ever again. I still love the Geissele’s but only at the $200 max price point. Any more than that and I default to Larue’s MBT trigger for $100.
🤩
I hope they make one for the VP9.
Great video
Thanks!
Thank you very much!
No way 800 too much. Go for it if you want to.
Very cool. Love the selector. Having a giant "Franklin Armory" badge with Ben Franklin's profile? on the side ruins it. Thank God they didn't paint the lettering white.
What's wrong with the name of the company who made it being visible?
@GBGuns I just don't like large badging on anything. Takes away from the gun imo. Same reason I won't buy a stribog. I just don't want or need my guns to be walking billboards for the company.
Would still rather spend the money on ammo. But interesting
A whole 3d printer setup to make unlimited switches would be half the price. If going fast is your goal, you know what to do.
It’s basically double tap from cod zombies so I binary everything to make shooting more fun
$800 (121gigawatts) that’s ridiculous!!!!!!
Awesome, however.. I live in the suburbs and my local gun range doesn’t allow rapid fire. I really wish I had a bunch of land to shoot whenever I wanted. Unfortunately we have a DEI boarder czar making everything insanely expensive
I live in the suburbs too. I drove 90min each way to film this
Can the trigger weight be reduced?
Honestly I'm surprised it took then this long to come up with the idea, I always thought it was a no-brainer. With stuff like this on the legal market in most states there's no reason for anyone to risk a felony by getting a Glock switch.
Let’s see you can get a switch for $30 or this over priced garbage for $800 not even including tax or shipping. Guess what one I’m gonna buy
The Glockomatic!
Got a oddball question. I have a g34 sbr but cant find out that if you have the franklin trigger in it, can another slide be put on and work as a normal glock and then switch back to the binary slide when you want to use it that way? just something iv wondered, would be kinda a pain to have to swap out the trigger and slide to go back to a longer set up for hunting and stuff.
Will the trigger work with a regular slide is a very VERY good question actually...
I feel like it should need to be.
@@caveymoley Its something iv wondered about, I even tried asking franklin armory but no response, and not been able to get an answer from anyone that had one sadly.
I got to get one !
Nice❤
Do they make a 19 size?
For the price point it should be coming with a barrel and recoil spring. Almost a 1,000 USD
For $800 the frame and everything should be included.
@@Callthefedsonme exactly my freaking point
@@lukeabram1674 seriously and the slides aren’t even appealing anyone who buys this is basically promoting them for free wiyh the big ass engraved Franklin armory name in the slide looks like garage to me if I had $800 to waste on it I still wouldn’t just for that reason
Great! Now make it compatible with a g19
Put an afterburner and a long boi on it
Just get a g flex trigger. Less than 200 bucks
Heck no, I rather have the switch
Trying to decide between this and a Gflex
Not that I have $$$$. Laying around to buy the conversion, but I’m concerned that the switch would prevent successfully mounting an optic as they all overhang the sides. The switch looks to go above the plate that Franklin included for aesthetics.
If on binary if the last burst is one round, is there any saftey feature besides having to put it on single, if not after one shot and a reload driving the mag into the gun, if the finger isnt holding the trigger will it go off when the slide is forward, can you demonstrate that, showing the results?
Need the 112MOA red dot for that slide 😂
I was doing fine with irons
Good lord... this is sad 😂 yall abide harddd
Where's your video of violating federal law?
Awesome!! Wish the price was somewhat lower ...
Dang it cost 300 more than an actual g17
More like $500 you can get a used police trade in for about $290
Do they have the slide for a Glock 19, 23 or 20?
perfect for all those g17 police trade ins that just popped up
Even cheaper, I picked up a new frame for about 75
Looked fun, almost as fun as a WOT OR FRT😮
Broken Loadout has entered the chat!
GRAND POWER HAS 2 ROUND BURSTS OUTSIDE USA
Some, yes, and I've shot an AP9 Stribog.
Kit alone is almost the same cost as beretta😂
Gimmick for 800.
Will you test it with a Radian Afterburner?
If that switch doesn’t go to full semi auto I don’t want it
I love bump firing my ars and keltec s2000 carbine and verious other xarbines. Its a gas man. To have a glock with this capability is the best. I can bump fire pistols but this really looks too cool. How much?
Too much
Over $800
Carnikon🎉❤
I hope he's doing ok, I miss his content!
atf after seeing this
14:20 thats it. You just doubling dude. Thats stupid for 800 dollars.
Nice toy but no practical use in CQC or defense
5:54 where did you acquire a Glock 17 gen 3 frame?
One of the major online retailers had them for 75, ironically the same price they were three or four years ago the last time I ordered one.
Run a 33 round stick mag man
I can't Wait til I get mines.. You should try putting a Tungsten guide rod in it to see how it changes your shooting..
Would you EDC it ?
I don't feel the need as I can pair well enough and am nor a fan of Glock, but I could see it as carryable
Is this legal in California? Asking for real.. seems pretty cool
Heck no! You guys got 10 round mags 🌈 🌈🌈🌈
This system would fuck hard in a .460 rowland glock 21 😂
It’s cool but if you ever gotta use it for defensive purpose, when the cops show up, it’s getting confiscated
I prefer guns I can afford to replace without spending half a pay check..
Pass
$800 or more.. Not for me...
Lol you're poor
@@mimzy4319 but very happy.. with the glocks I have and sigs I have
@@mimzy4319no he’s just a smart individual unlike you you lack common sense and brains why would I pay $800 for a binary system when I could get a 3d printer and print out switches for 1/4 of the price ?
would be cooler in .380
Costs as much as two gen 3 glocks or 3 cases of range ammo, yet doesn't include a barrel or recoil assembly. Hm.
Can’t even do a gen 4 or 5 😂
There are more Gen 3s out there than anything else, so it made sense to make for that generation first.
If my Stribog SPA3 would shoot hollow points it would be a great home defense firearm, but it doesn't. So it just sits in the safe.
I hav ea couple SP9A3s and have run dozens of different types of hollow points through it without issue. Which ones have you tried?
You around the Browns camp area?
Or mcguire reservoir area
Yeah.
Near Jewel somewhere
That's $300 worth of product, but I bet people will buy them anyway.
Unique slide required for a unique trigger, patented, this is jot as inexpensive to make as a regular slide or trigger, plus it was designed instead of simply copying.
$800+ tax/shipping. No thanks, years later and my and many others Scorpion binary triggers do not work.
Didn't the A7F get a list of the similar parts that were sold to Ar ppl and then go get them? Matter of time.....$900 toy plus the rest...
Wasting good training ammo. Get the selector switch if you want to get real and waste more good training ammo. Cheers!
How was it a waste? I learned how controllable this is and found my speed limit with it.
@@GBGuns Respectfully, it’s just a gimmicky tool for people to make noise and show off. And quiet possibly cause injury or death to an inadequately trained kid, or adult. I’ve on occasion shot the 18C and I must admit it definitely put a smile on my face. I mean you no disrespect at all sir.