Flysky fs-i6s CAT 339DL Hydraulic Excavator Pump Mixing.
HTML-код
- Опубликовано: 10 сен 2024
- Hi all, in this video I describe how to mix you transmitter stick functions to coinside with bringing the hydraulic pump on only when called for. Any questions please add them in the comments section. Please like and subscribe 👍
Very well stated directions , thanks for putting this up 👍👍
Thanks for the very kind words, your very welcome. 👍
simple ,easy to follow with great results ,this saved me a lot of time , cheers
Thanks, glad I could help 👍
your awesome my friend. i did this to my dump truck and trailer. works sweet as. love the video great detail. u should do more.
Thanks 👍
what a great video thank you so much for posting it friend
You're welcome 👍
Thx. Ists very Importen! Greetings from germany.😎👌
Thanks, hello from England 🇬🇧
Thenks
You're welcome 👍
@@ianyams ai indonesia
👍
Great video thank you for the help 👍👍
Thanks, you're welcome, glad I could help.
Hello. Thank you for making this video. Unfortunately the method that you show here isn't working for me too well. For example if I set up channel 1 to work with the pump successfully? It will not stay programmed once I go to another channel. It's like when I program one it overwrites the previous channel. How do you get all channels to work at once with the pump???
You're welcome. I don't know your problem, sorry.
thanks for this, I've been wondering how to do this for my dozer. cheers. sub'd!!!
Thanks, you’re welcome 👍
Brilliant 👍
Would this work with the FS-I6X? How do you also set up the radio to have full rotation? Actually, the rotation follows the stick's movement...
Hi, I'm not sure with the I6X as I've never had one. Full rotation of what?
@@ianyams of the "turret". I don't understand how to configure the transmitter to get it to rotate and not stop once the stick hits it's stip
What make and model do you have?
Nice excavator ,i give you potatoes
hello mr ianyams how you doing i want help you please i have earth mover 870k with FS i6s 10ch same your radio i want learn how can do mix the pump i want do pump on the request like you please learn me step by step i tried to do that before but it didn't work? i hope you help me thx bud
Hi, It's all step by step in the video.
Hey, my friend, I am trying to set my flysky to my hydraulic skeet steer and it's activating the servos for the valves but not the pump ? I set it up just like you did I have a flysky afhds a2
Hi thanks for the question but I'm unsure why yours doesn't work.
@ianyams I actually reversed the channel for the pump, and it started working
@@gf414dr2 brilliant, well done.
Good info to know, thank you. What battery connector dose this excavator model have?
You're welcome. The battery connector is a Dean's T plug.
Bonjour auriez vous l explication pour chariot elevateur avec flysky pl18 ev ?
Hi, sorry no.
Hi mate i love to do this to my rc hydraulic LH954HB ce certified exovater but i can not let my in on the transmitter?
How can i fix my transmitter problem to let me in to the spanner it will not let me ?
How can I have the mixing but only have the pump running at 15% so the lines are still primed?
I'm unsure as I've never needed/used that operation.
I have the hyd. Track loader can I mix the hyd pump as I use the loader ??
Yes it’s the same method I’ve have shown as long as you have the same transmitter as the one shown. The difference will be you only have two hydraulic channels on your track loader whereas three on the excavator.
Thanks I will watch your video again
You're welcome.
Hi great video been really useful to me, I’m just struggling to stop the pump motor speeding up to fast and foaming the oil. Did the positive end point to 20% left negative at 100. Is there anything else can try ? Any help would be great thank you
Is it possible to start the machine with the pump always at 20% and then, as you move the sticks, increase the force, so as not to have so much slingshot effect?
Hi, I would imagine you can but I’ve had mine set like this for a long time now without problems 👍
Thank you for being so clear in your details👏👏.i have the Rc4wd loader an my switch for the pump is the 1st on top to the left do I leave that switch in the off position? I just wanna make sure before I go an do this. Again thanks👏👏😀
Brute Force hi many thanks for the kind words. Yes leave the switch in the off position but you will notice when you have completed the mix that the said switch will operate the pump as it did before if you turn it to the on position incase you need the pump to run permanent in the future. 👍
Cool thanks I really appreciate it my friend 😀
Brute Force anytime mate 👍
How left joystick gimbal always on center position?
Hi, it comes from the factory with a spring return.
@@ianyams oke thank for your info
@@agungbudiyono3327 you’re welcome 👍
You are very easy to understand ! How do you program the tracks
Hi thanks, the tracks are on esc’s
Hi. I reset my transmitter and connect it again. But it cannot control excavator . Only rotate and wheels
How to setup it again?
Hi, why did you reset the transmitter?
I settings it wrong and i want to go back just reset factory . And then it not working
Did you rebind the reciever to the transmitter?
Ready rebind but it not working
I mate I need some help as I’ve just got a new flysky and just bound it to the hydraulic digger and done the video a the pump runs but none of the 3 hydraulic cylinders do anything.
Hi, are the servos moving the control valves?
Hi great video, could do with some help tho My pump is running very fast after following your video and comments on limiting the positive end point 20%. Just seems to speed up to a high speed and foaming the oil up abit. Any ideas what else I can do thanks ?
Hi, thanks for the kind words. Ok if your pump is on channel 5 like mine, go into settings select end points and try reducing either the plus or minus values, trial and error. Or try the sub trim in the same menu, again trial and error.
I have the same radio with my dxr2 dozer
Need to use one stick for tracks and the other for blade up down and tilt. Can you help.
Hi, possibly just change the connections over on the receiver until you get the desired controls on your transmitter.
Did that work I also have the same dozer and was wondering how to the tracks with one stick
@@jesselonghi9016 it can be done but I’m unsure how to mix the tracks. I’ve just acquired the Faroe CAT 953c tracked loader and uploaded a couple of videos.
Hi
I would like to perform the same mix as on your video, is the basic version of RC sufficient?
Or do you need a specific version
Hi, sorry I don't understand what you mean by version of rc?
Hi. very ice video. Could you do an explanation of the Offset, Neg and Pos functions. Also is it possible to setup a delay? So for example the pump throttles down 2 seconds after a stick was released?
Hi, thanks for the nice words. Unfortunately I don't know quite how it all works and ties together. As for the delayed pump I'm unsure of that too, sorry 🙈🤷♂️
How do you increase the hydraulic pump speed using this transmitter
Hi, is your pump controlled by an esc?
I tried setting my liebherr 954 using your example but the pump don't come on
tony standrew hi sorry to read your having problems. Have you double checked that your inputs are the same setup as mine?
hello my friend how you done so how can you program your battery 3s on this radio control FS because i have same this radio on my earth mover 870k my problem is when the battery is low and the pump stop work the battery still full on my radio screen even the alarm not working too i to changed the RX set up i turn
high volteg.6.0 to 11.1
alarm.4.2.to 5.8
low.4.0 to 3.0
nothing happen? even the battery does not go down with use like any rc i use battery 11.1 3s 2400mAh 35c if you have any idea about this i hope help me thx again dude nice video
Hi, many thanks. My setup is with a 3s lipo also, these are my settings, tx high 6.0v alarm 4.2v low 4.0v. Rx high 6.0v alarm 4.2v low 4.0v. I have not had any problems like you described 🤷🏻♂️
@@ianyams thx pal but this RX set up comes standard like first time you adjust them by yourself on your battery i remember when i was i talk with youtuber land savior about this thing he told me adjust high volteg and then adjust alarm? because this setting comes standard.. well thx again buddy you have awesome channal we wants more video
Many thanks for the kind words 👍 I have never adjusted my factory settings as mine seems to work fine.
@@ianyams well done👍dude but 4me i will to changed my fu..radio control i'm looking 4 futaba fx 32 about the FS i6s i will put it on my rc tamiya tundra or tamiya bruiser well thx again buddy is beautiful channal i want to see more good luck✌
Hi there I've done as your video I have a 360l i have to switch the pump on using switch a on my controller usually I've done the mix but still have to switch the pump on so its on permanently love to be able to do the mix as shown to save power and pump life any ideas what I need to do ? Cheers
Hi, try going into settings and select the channel that is associated with the switch and change it from on to inhibit, if that doesn't work just reverse what I've said, it's only an idea.
@@ianyams fantastic thanks for your knowledge thats worked cheers
Brilliant, glad I could help 👍
About the ESC of the pump, is the break enabled between backward and forward. Should the pump turn only one way and how is managed with the radio settings. Looking at the initial channel graphs, ch5 is 100% to the left but is not turning? When you move a stick, the graph of ch5 is gradual, does that means the pump increase in speed gradually?
Hi, the pump only goes one way and is at a constant steady speed set by esc, the speed is set on the channel 5 end points.
While operating the excavator, at what position is your channel 5 switch? So the channel 5 graph is no indication of the pump rotation speed, it is either at determined endpoint speed or stopped?
I have a Lesu pc360 and there is no indication which it should turn, I can only assumed from looking at other video.
Has the pump got a name or number on it?
ianyams I would have to uninstall the pump to see the marking at the end of it. You can see pictures of it at this facebook page. facebook.com/RC-Construction-109278837508460.
Set up a friend's hydraulic tracked loader very similar to what you've done, using that radio, but had it so the pump would only come up to about 50% off one channel, if you used another channel it then ramps the pump speed up to whatever maximum you set for it. Did it this way so it didn't slow down the movements when using more than one at a time.
On a side note, looks like I've copied you haha, bought a 580 few weeks back, love it and have since got a Faroe loader similar to yours, second han though, so she's getting a big strip down an rebuild
Brilliant 👍 I started with a 580 too then the addiction started 😁 still love the Huina though, I've done some videos on here of upgrades and mods.
Awesome, I'll be sure to have a look, already done a few mods on the 580, great little machine. Subbed
Thanks Glad you like the content. I try to upload vids that I have struggled to find or can't find or requested 👍
Hi, great video you have there mate. I tried the steps according your steps but my pump still run after I turn on the pump. do you know why it happened? dont know what else to check.
Thanks, Double check your have followed the instructions as described.
Hey I have the same radio mines all black though it has firmware from 2016 on it. Could this be the reason why I don't have an option to mix individual channels? I can only mix 1 channel not 3. Do you think the updated firmware would allow me to mix 3 channels and not only 1?
As per our conversation 👍
@@ianyams haha yes thanks for all your help
@@yzboii anytime 👍
Hi, very useful video, thanks. Whats is your settings in the end points menu?
Hi, thanks. I will have to check for you, it’s packed away at the moment.
Thanks for ur help mate, With the wheels can u make these to be a 3 way switch or just 2 on and off
Thanks for the kind words. Unfortunately I don't understand your question about the wheels.
@@ianyams the wheels where u operate the tracks , can they be made to be used as a 3 way switch, was asking at the time for a friend who has the flysky
@@TheNZSlayer I don’t think so, I’ve never tried it though 🤷🏻♂️
can you tell me what version of fs-i6s firmware you got.it indeed help a lot but my transmitter is linear on throtle.so in the middle stick.the esc and motor think im on muddle stick
Hi, firmware V3.0 installed.
@@ianyams oh i see.same as mine.but for some reason.it follow the linear curve.only up and right and for the throtle.middle position.motor run like its on 50%
It sounds like something in the settings 🤷♂️
nevermind.i recheck my radio and it still at v 2.00.need to download the 3.00 firmware.
thank you sir.you video is so helpfull.cheers
love this, So how would i speed up the pump if i needed to? just a hair?? just got the volvo 360l with the same controller
also could you explain the 2 esc controls for the tracks? mine are just blinking and not working. THANKS!!
Hi thanks for the kind words. Ok on your transmitter click the spanner icon to get into settings, then click end points, if yours is setup the same as mine your pump will be channel 5 on the receiver, click 5 and click positive, the percentage should be about 20% if you increase that it should make the pump faster, be careful though as not to go to fast.
Matt Alfieri are the tracks moving with transmitter input?
ianyams I figured it out last night! haha thanks for the reply, all is working great now. Just need to tune how the pump speeds up when I want to control, it doesn’t go so fast at the top end. Cheers!!🍻
Matt Alfieri brilliant, well done 👍
itried to do that in my i-6s.it only run 1 side.it follow the throtle curve
Make sure your settings are the same as mine.
Great video, the problem I'm having is my pump never goes to full RPM. Pump is Channel 5 which is also set to a switch to turn the pump on and off. I move the stick full in one direction and the pump maybe is 30% RPM. Same for all mixing. Set up exactly as you have with the EXP and the -100/100. Any ideas?
The other thing that is different is I don't have the number after MIX which I assume is just different mixing programs. . it just shows Mix then ON/OFF so I can only mix 1 master/slave?
The fact I only have 1 mixing program might be firmware. I'm on version 3.0 from 2017 and 7.13 was released 6 months ago. I'm not sure if that will fix the fact that I can't get the pump to spool 100%. If i adjust the subtrim all the way to the max 120 I can get say 50% - 70% out of the motor. I notice that when i look at the channels page the switch for channel 5 is up and the black bar is all the way to the right, this might be the issue,
Thanks for the nice words. I'm not sure but it's always best to have the latest firmware update, try that 1st.
@@ianyams Reading your comments below you too have the 3.0 Firmware. Can you check on your about page of your transmitter and confirm the firmware for me. Just want to make sure we are the same. Thanks
@@sandman2495 yes mine is v3.0
@@ianyams Well then that leaves me at a total loss on why the mixing is different. back to running the pump all the time i guess
Hello friend nice vide I really appreciate the shearing of your knowledge! I like to know if I can set up my track loader so the pump doesn’t runs continuously I assuming is the same way so could confirm this before I try do it my self lol I jus want to make sure before I try so I don’t mess up anything I have the faroe track loader similar to your but I’m sure your is way better then mine . Please thank you!🙏🏻
Hi and thanks. Yes exactly the same just with two mixes 👍
Thank you 🙏🏻 so much for your help
You're welcome.
I was just trying to figure it out but is but can’t find that Chanel list when I press fly mode is only showing (Chanel:11 on) and can’t figure it out why?
Don't press fly mode just swipe right from the main screen.
Hi! I have the same Flysky and it does not work.
Oh dear, unfortunately I don't know your set up ☹️
Ian is it possible to slowdown the movement thanks👍👍
Yes, I will pm you.
What is your channel 5 aux set to?
Hi, aux 5 is the pump on the top left switch of the handset.
@@ianyams ok so how did you set it up with the switch?
@@ianyams I've done everything in the video. And now set my chanel 5 to the top left stick? But when I move my right stick to the left channel 5 dosnt move, the bar stays to the left and dosnt go into the middle?
@@ryanclist2378 is your pump plugged into slot 5 on your receiver?
@@ianyams yeah
Did what you explained but in my case it works only one way. Any idea what's going on?
Try redoing it again.
@@ianyams i'l give it a shot, thank you!
👍👍
I did it twice and didn't help. I'll do it once again to be 1000% sure I'm doing it correctly. I think that something is wrong because it's eating the battery so fast!
Ok, is the pump Only working when you move a stick on your transmitter?