This tool makes job easy. thats why there r so many people without mech/elec studies doing this job .Sometimes u ask with such tools is it worth to get a diploma from a poly or uni.I think now its a waste of time to get studies done,get basic knowledge dont waste big money ,invest in good tools that will do most things. Nothing against L.M auto,ifrom my experience u r qualified ie BT or BTS
Yes, tools like this make your life easier... I did many jobs with NCS expert, WinKfp, E-sys, etc... but this is definitely quicker and more intuitive to use... Thank you for watching and for your comment!
very interesting to see the level of computer control in todays vehicles, not surprising because I have always known it was there, it also gives us an insight into the progression and intention of programmers to take away control from the operators and drivers. It is not surprising therefore that billions of taxpayer's money is used to subsidise manufacturers, this is not just about creating jobs, this is about creating a power structure.
😊 Right to repair... Some of this stuff it is slowly taken away or made very difficult or expensive to the ordinary garage or individual... So, you are forced to go to the dealer, which obviously will not install second hand parts... 👍👍👍
Hello, I would like to know some information please for the j5 create usb ethernet adapters I searched on the internet to buy it I did not find the same one can I buy it anywhere what usb ethernet model thank you.
Where do you learn the autels full capability had a headlamp module to code on a bmw f10 today for the angel eyes managed to recode the frm but couldn't get it to work but the module was a cheap one off Amazon. Thanks
I highly advise you to use one... Although, coding only is not so risky, and usually takes less time... So, if your battery is healthy and you are only coding one module, you might get away without using one... but again, you should do use it! 👍👍👍
@@cristianohinkenickel5882 Procedure is the same/similar... I know what the VO is... and that does not need to be touched when you replace parts like for like... Again, the VIN number will need to be corrected, possibly some coding as well... That is what I am showing on this video... there is no VO involved... 👍👍👍
🤷♂️ Don't even remember if I had the IM608 at this point... Even if I did, the IM608 wouldn't be able to it, due to the lack of an ethernet port... Is no designed for that... can do coding, but it is a bit more restricted... 👍👍👍
Hi, lm doing a Audi A4 b6 1.9tdi and the immo light is not going off also no engine check light. Tried to put machine but no communication. could it be the cluster or or something. Help plz thank you
I have similar problem...difficult to diagnose it...earlier it show wheel speed air gap rear right..I changed the speed sensor still same issue....can u help ?
Did you get the software from old module and put it back? I couldn't see any of this procedure, is that doing its thing automatically without taking the old software back?
Hello Luis , I admire your work with the cars, but it is not good to make videos with a 3000 euro scanner, because most of your viewers do not have such an expencive tool.Its better to use the cheap chinese clones instead !
The best tool is yourself... The idea is to show the process, the thinking, etc... The tools, you can use whatever you want... Thank you for watching! 👍👍👍
I think you are missing the point... If you use a different tool, the procedure at its core still the same... or at least very similar... Does not matter if you are using an Autel, a clone Icom, a CGDI, or even E-sys... though the last one can be a bit more tricky... 👍👍👍
@@SabretoothBarnacle i am software engineer work for Mercedes and develop ecu and bcm we are hardcoding with c++/c language this is just pressing buttons and the binair digits are changing
Coding, programming, flashing... etc... All comes down to play with the control module software... correct? On the title, I put coding/programing... I absolutely agree that in this situation the word coding is more specific to what I did, the fact that I used the word programing it is to make sure that the person that will see this as programming, can also find the video... In the end, those technicalities that are irrelevant here... Just my opinion... 👍👍👍
Always have a great capacity to make the things Make them look easy to do👍
😊
Thanks!
👍👍👍
More rain 🌧️ ... Wish we had same weather in Dubai..
🤣🤣🤣
You want the rain, we want the sun...😊
👍👍👍
This tool makes job easy. thats why there r so many people without mech/elec studies doing this job .Sometimes u ask with such tools is it worth to get a diploma from a poly or uni.I think now its a waste of time to get studies done,get basic knowledge dont waste big money ,invest in good tools that will do most things. Nothing against L.M auto,ifrom my experience u r qualified ie BT or BTS
Yes, tools like this make your life easier...
I did many jobs with NCS expert, WinKfp, E-sys, etc... but this is definitely quicker and more intuitive to use...
Thank you for watching and for your comment!
very interesting to see the level of computer control in todays vehicles, not surprising because I have always known it was there, it also gives us an insight into the progression and intention of programmers to take away control from the operators and drivers. It is not surprising therefore that billions of taxpayer's money is used to subsidise manufacturers, this is not just about creating jobs, this is about creating a power structure.
😊
Right to repair...
Some of this stuff it is slowly taken away or made very difficult or expensive to the ordinary garage or individual...
So, you are forced to go to the dealer, which obviously will not install second hand parts...
👍👍👍
Excellent repair video 👏
Thanks!
👍👍👍
Hello, I would like to know some information please for the j5 create usb ethernet adapters I searched on the internet to buy it I did not find the same one can I buy it anywhere what usb ethernet model thank you.
Good morning Nice job always
😊
Thanks!
👍👍👍
Thanks for the video. Excellent job as always.
Thanks!
👍👍👍
Loves the video man!! Keep them coming
😊
Thanks!
👍👍👍
Where do you learn the autels full capability had a headlamp module to code on a bmw f10 today for the angel eyes managed to recode the frm but couldn't get it to work but the module was a cheap one off Amazon. Thanks
Being a cheap one could be one of the problems...
👍👍👍
Where in UK are you?
Can you show the abs pump bleed procedure using maxisys
I will next time...
👍👍👍
Did you use battery maintainer?
I highly advise you to use one...
Although, coding only is not so risky, and usually takes less time...
So, if your battery is healthy and you are only coding one module, you might get away without using one... but again, you should do use it!
👍👍👍
Hello, if its only encoding, do I realy need to have a subscribtion from Autel? Can the Autel do encoding offline?
You have clearly not watched the video till the end...
👍👍👍
Hi to you my master
😊
👍👍👍
Hi,
Is this the same procedure for the e60?
If its a second hand part no need to change the VO?
Thanks
Hi
The VO?
NO...
Some modules need to change the VIN and the coding...
👍👍👍
@@LMAutoRepairs thanks
The Vehicle Order?
So this is not same procedure to E series ABS/dsc replacement?
Thanks again
@@cristianohinkenickel5882
Procedure is the same/similar...
I know what the VO is... and that does not need to be touched when you replace parts like for like...
Again, the VIN number will need to be corrected, possibly some coding as well...
That is what I am showing on this video... there is no VO involved...
👍👍👍
Was the unit replaced brand new or a used one with a different VIN from another car?
🤔
The answer is on the title of the video...
🤷♂️
👍👍👍
Hi, I would like to ask you if programming can be done after your software update has expired. I am using 908p.
No...
Any online features will stop working...
Thank you for watching!
@@LMAutoRepairs Thank you my friend!
Why you didnt do this job with Autel im 608 pro ?
🤷♂️
Don't even remember if I had the IM608 at this point...
Even if I did, the IM608 wouldn't be able to it, due to the lack of an ethernet port...
Is no designed for that... can do coding, but it is a bit more restricted...
👍👍👍
Thanks Louis.
😊
👍👍👍
Did you have to change the module alone or with the dsc pump
I changed everything as one unit...
👍👍👍
@@LMAutoRepairs ok thank you
Amazing video 👏🏾
Thanks!
👍👍👍
Really nice job as usual :-)
Thanks!
👍👍👍
Hi, lm doing a Audi A4 b6 1.9tdi and the immo light is not going off also no engine check light. Tried to put machine but no communication. could it be the cluster or or something. Help plz
thank you
Can you communicate with the engine control module?
Thank you for watching!
@@LMAutoRepairs l tried to put the machine but its not communicating with the ECU
OK...
Start with the basics...
Fuses, connections etc...
Check powers and grounds at the ecu connectors...
Lastly CAN network...
@@LMAutoRepairs ok thank you
nice one ,good video,good fix
Thanks!
👍👍👍
Hiii...what maxisys model is this scanner??? Thank you
MS908P
Thank you for watching!
👍👍👍
Hi. Great video as usual👍
If you were going to buy a new Autel scanner today what model would you go for?
Depends on the needs...
As a general scanner, I would try to buy the Ultra...
Thank you for watching!
mk 906 pro ts scanner can coding ?
Not sure... I never used it...
Sorry...
👍👍👍
I have similar problem...difficult to diagnose it...earlier it show wheel speed air gap rear right..I changed the speed sensor still same issue....can u help ?
Have you watched the other video on this car?
It might help you...
👍👍👍
@@LMAutoRepairs yes I did...I changed the abs also....but still same error...now last iam gonna change the wheel bearing...hope it's fixed then
Have you measured the wires etc...
You can have a break on the wires elsewhere...
is the ultra can do coding and programing??
I believe it does...
But have not digged into it... the price put me off... 😋
Did you get the software from old module and put it back? I couldn't see any of this procedure, is that doing its thing automatically without taking the old software back?
No...
The software is whatever was already on the replacement unit... this just code it to the car...
Audi Q5 2015 3L. engine control module no signal code vaG 1314 engine not starting
You mean, you can't communicate with the engine control module?
Thank you for watching!
How come you dont repair japanese cars? Is it because they are so reliable ?
🤷♂️
I did some, and some to come...
👍👍👍
Good video
Thank you!
👍👍👍
0:06 0:07
👍👍🌷
Hello Luis , I admire your work with the cars, but it is not good to make videos with a 3000 euro scanner, because most of your viewers do not have such an expencive tool.Its better to use the cheap chinese clones instead !
The best tool is yourself...
The idea is to show the process, the thinking, etc...
The tools, you can use whatever you want...
Thank you for watching!
👍👍👍
Exactly this is my point. All the job is done by Autel automatically , so if you do not own one there is no interest
I think you are missing the point...
If you use a different tool, the procedure at its core still the same... or at least very similar...
Does not matter if you are using an Autel, a clone Icom, a CGDI, or even E-sys... though the last one can be a bit more tricky...
👍👍👍
This is not programminy
verb: program
1.
provide (a computer or other machine) with coded instructions for the automatic performance of a task.
Thanks...
The programming you are thinking about, it is usually referred as flashing...
@@SabretoothBarnacle i am software engineer work for Mercedes and develop ecu and bcm we are hardcoding with c++/c language this is just pressing buttons and the binair digits are changing
Coding, programming, flashing... etc...
All comes down to play with the control module software... correct?
On the title, I put coding/programing...
I absolutely agree that in this situation the word coding is more specific to what I did, the fact that I used the word programing it is to make sure that the person that will see this as programming, can also find the video...
In the end, those technicalities that are irrelevant here...
Just my opinion...
👍👍👍
what a shambles... all over the place
Not sure I understand your comment ...
Creo que tengo el mismo problema
Why bother with BMW with this Chinese crap?
What exactly are you referring to?
👍👍👍