Bye bye wheel bearing 👋 don't get me wrong, building something like this with his kid is AWESOME and I'm all for it, but you need to do things properly. Judging by the way this thing is built it's going to see some heavy work, I don't think it's "Just a toy"
@@MaxMolotko the bearings looked dry...or very lightly greased. They need to be completely packed full of grease for them to operate properly so they don't wear out quickly. The guy just took a finger full of grease and wiped it on the outside. That bearing will wear out much more quickly than it should. It probably only has about 2% of the grease it requires.
Respectfully, I strongly suggest you open up those wheel bearings and add more grease when it comes to wheel bearings most of the time there is no such thing as too much grease with the amount of grease you have in there you are begging for a bearing to seize. If you are going to do any serious work with that tractor, you might even consider installing a grease fitting into each of the wheel bearing housings.
@@jgalloway528the steer axle is grease hubs the rears may be ok if gear lube oiled by the differential but that would require lifting each side of the drive axle individually (tipping it to left and right sides to get the lube to the axle ends) while topping up the oil to make sure it gets to the wheel bearings before driving the machine...
Nice rebuild, no way some of those parts are new though, especially looking at the paint job. Please tell me you came back and repacked those taper bearings, otherwise I see you repeating this job very soon.
Please tell me you took that hub back apart and added more grease. That's barely anything, especially for something expected to have a higher load. Ooooooffffff
Im not like the last Contributor being respectful. STOP USING THE TRACTOR IT IS NOT SAFE. UNEXPECTED BEARING SEIZURES CAN LEAD TO HANDLING MALFUNCTION CAUSING SERIOUS INJURY. All those bearings you installed are heading for the scrap bin very quickly without any other damage that will be caused when they SEIZE. There are available videos on RUclips on how to pack a bearing with grease. You can also purchase from any bearing shop, Autoparts Shop and hardware stores a bearing packer kit. You have to have a reputable greasegun. THe bearing is placed in the packer unit and youjust pump grease until it comes out past every roller or ball bearing etc. As has been previouslly stated you can't overpack the bearing, For that tractor, I would expect to use two cartridges possibly three. Any excess grease is pushed into the housing and provides a form of reserve and retention of the grease in the bearing.. .
please learn how to correctly hand grease a tapered bearing slathering grease on the outside of the rollers is no good... put a dab of grease on your palm then drag the tall side of the bearing into the grease in your palm until grease come out between the rollers on the other side then rotate to the next roller position all the way around the bearing the way shown in this video will cause the bearings to run without lubrication causing premature failure. there are many videos on how to correctly grease a tapered roller bearing a good youtube video on this is... DIY: How to Pack a Bearing with Grease by 4DIYers no affiliation
Who P'ed in your cheerios? Keyboard mechanic get'n bent outa shape over the amount of grease. Do you really think this thing is going to see highway use? Can't a guy build something awesome and fun with his kid and show the world without unneeded nit picking? This was an awesome video and should be applauded. Here is a video for you... DIY: How to not cry over spilled milk like a big boy.
@@lordirras 1) I'm not a keyboard mechanic I'm a well certified mechanic ase a1-a8 t1-t3, Medically retired 63h/91h 2)even on slow speed vehicles you can destroy the bearings by not properly greasing them this can become dangerous specially when the bearings lock up from improper greasing which at even 10mph can cause a wheel to lock up or axle to break causing a wheel to come off and the machine to rollover
You have your title worded wrong it should be mini tractor construction kit 120 patts the word (for) shouldn't be in there but otherwise great video and that little lawn mower engine it's supposed to run that it seems like that would be putting a lot of stress on that little lawn mower engine
well looking at that differential there's a drain plug, those bearings don't need grease they should be riding in gear lube that's basically a miniature truck rear end !
I wonder how many people in the comments mention the fact on how poorly he packed them bearings ...jeesh but I'm still going to watch the video all the way through and give it two thumbs up because it helps with the algorithm 👍👍
@@MaxMolotko судя по такому малому понижению -не автомобильный, к сожалению. А то могла бы возможно подойти блокировка газ 66, если на его основе мост был бы
@@СашаПетров-н9т да, понижение редуктора слабое, но в целом получилась хорошая скорость, на первой 3км.ч. на полном газу, на четвёртой 10км.ч. на полном газу
Bye bye wheel bearing 👋
don't get me wrong, building something like this with his kid is AWESOME and I'm all for it, but you need to do things properly.
Judging by the way this thing is built it's going to see some heavy work, I don't think it's "Just a toy"
I thought the very same thing. First issue I saw.
I don't understand what's wrong with the wheel bearing🤔
@@MaxMolotko the bearings looked dry...or very lightly greased. They need to be completely packed full of grease for them to operate properly so they don't wear out quickly. The guy just took a finger full of grease and wiped it on the outside. That bearing will wear out much more quickly than it should. It probably only has about 2% of the grease it requires.
That axle looks like a floating axle and shouldnt have any Grease on it and will buy lubed by oil from the diff. I can be wrong
Yeah, he's kinda dainty with the grease isn't he,😂
Respectfully, I strongly suggest you open up those wheel bearings and add more grease when it comes to wheel bearings most of the time there is no such thing as too much grease with the amount of grease you have in there you are begging for a bearing to seize. If you are going to do any serious work with that tractor, you might even consider installing a grease fitting into each of the wheel bearing housings.
I've already carefully lubricated everything again, thank you!
@@MaxMolotko Cool! I would hate to see all that hard work get wasted!
@@MaxMolotko I'm glad to read this.
Those are oils bath bearings. They get lubricated from the oil in the axle
@@jgalloway528the steer axle is grease hubs the rears may be ok if gear lube oiled by the differential but that would require lifting each side of the drive axle individually (tipping it to left and right sides to get the lube to the axle ends) while topping up the oil to make sure it gets to the wheel bearings before driving the machine...
So cool. Wouldn’t be neat with a loader or a push blade on the front
Nice rebuild, no way some of those parts are new though, especially looking at the paint job. Please tell me you came back and repacked those taper bearings, otherwise I see you repeating this job very soon.
I made this tractor myself, this video is just the assembly. There is a video on the channel of how I made it. I lubricated the bearings again)
Please tell me you took that hub back apart and added more grease. That's barely anything, especially for something expected to have a higher load. Ooooooffffff
disassembled and re-lubricated
Verry nice build. Congratulation to both builders!
Thank you❤
Nice rebuild shame, the bearings are not going to last, too long as they were not packed with grease properly
🙂
🚜🔥👍
Im not like the last Contributor being respectful. STOP USING THE TRACTOR IT IS NOT SAFE. UNEXPECTED BEARING SEIZURES CAN LEAD TO HANDLING MALFUNCTION CAUSING SERIOUS INJURY. All those bearings you installed are heading for the scrap bin very quickly without any other damage that will be caused when they SEIZE. There are available videos on RUclips on how to pack a bearing with grease. You can also purchase from any bearing shop, Autoparts Shop and hardware stores a bearing packer kit. You have to have a reputable greasegun. THe bearing is placed in the packer unit and youjust pump grease until it comes out past every roller or ball bearing etc. As has been previouslly stated you can't overpack the bearing, For that tractor, I would expect to use two cartridges possibly three. Any excess grease is pushed into the housing and provides a form of reserve and retention of the grease in the bearing..
.
please learn how to correctly hand grease a tapered bearing slathering grease on the outside of the rollers is no good... put a dab of grease on your palm then drag the tall side of the bearing into the grease in your palm until grease come out between the rollers on the other side then rotate to the next roller position all the way around the bearing the way shown in this video will cause the bearings to run without lubrication causing premature failure. there are many videos on how to correctly grease a tapered roller bearing a good youtube video on this is...
DIY: How to Pack a Bearing with Grease by 4DIYers no affiliation
Who P'ed in your cheerios? Keyboard mechanic get'n bent outa shape over the amount of grease. Do you really think this thing is going to see highway use? Can't a guy build something awesome and fun with his kid and show the world without unneeded nit picking? This was an awesome video and should be applauded. Here is a video for you...
DIY: How to not cry over spilled milk like a big boy.
@@lordirras 1) I'm not a keyboard mechanic I'm a well certified mechanic ase a1-a8 t1-t3, Medically retired 63h/91h
2)even on slow speed vehicles you can destroy the bearings by not properly greasing them this can become dangerous specially when the bearings lock up from improper greasing which at even 10mph can cause a wheel to lock up or axle to break causing a wheel to come off and the machine to rollover
Get rid of the stupid drama music! No one needs music and especially not drama music just to watch you assemble a tractor.
🥺
You have your title worded wrong it should be mini tractor construction kit 120 patts the word (for) shouldn't be in there but otherwise great video and that little lawn mower engine it's supposed to run that it seems like that would be putting a lot of stress on that little lawn mower engine
First mistake, didn't pack the tapered bearings properly. They won't last long that way.
Nice result. I love the colors !!!
❤💚
❤️❤️❤️❤️❤️👍👍👍👍👍👍👍👍👍🇮🇩
Bel lavoro ma ancora meglio il lavoro con il figlio complice della creazione del mini trattore 🎉❤
Чертежи можно получить и список деталей?
Все делал с головы без чертежей), полное видео как я его делал и что для этого использовал сдесь
ruclips.net/video/QsIAI15HPKA/видео.html
you should add an axle to be able to connect some implements on it !
great work though !
well looking at that differential there's a drain plug, those bearings don't need grease they should be riding in gear lube that's basically a miniature truck rear end !
exactly!
I wonder how many people in the comments mention the fact on how poorly he packed them bearings ...jeesh but I'm still going to watch the video all the way through and give it two thumbs up because it helps with the algorithm 👍👍
❤
Great job . Thanks .
i would love to get one for grandson.
Привет как всегда интересно и не скучно так держать 🎉
Спасибо большое!!!
Awesome!
Where did they get those parts? They are awfully crude.
old parts from car dismantling,
made it myself)
И? В чем прикол?
🤔
What !? It is RUclipsr make tractor for his son
this is now his favorite toy 😊
Супер тракторец получился, просто класс!!!
Parts used? Sources?
spare parts from car dismantling, homemade tractor😊
Красиво всё вышло и музыка хорошая фоном.
Ага
Отлично получилось 👍! А от чего задний мост?
@@СашаПетров-н9т с какого-то старого электрокара, я так понял что с того, что на жд вокзале возил чемоданы)
@@MaxMolotko удобно, что укорачивать не нужно). И мощная железяка при этом. Интересно, а какой там главный редуктор?
@@СашаПетров-н9т 1:2.5
@@MaxMolotko судя по такому малому понижению -не автомобильный, к сожалению. А то могла бы возможно подойти блокировка газ 66, если на его основе мост был бы
@@СашаПетров-н9т да, понижение редуктора слабое, но в целом получилась хорошая скорость, на первой 3км.ч. на полном газу, на четвёртой 10км.ч. на полном газу
Wish we had access to the tractor here in the states! Nice build.
Гарний тракторець
Дякую