@@saadinnovativeideas analogWrite(enA, Speed); // Write The Duty Cycle 0 to 255 Enable Pin A for Motor1 Speed analogWrite(enB, Speed); // Write The Duty Cycle 0 to 255 Enable Pin B for Motor2 Speed delay(500); } void loop(){ s1 = analogRead(ir_R); s2 = analogRead(ir_F); s3 = analogRead(ir_L); For example this? Should I replace it with digital?
00:10 Learn to create an Arduino firefighter robot 01:04 Robot designed to handle fire disasters 01:20 Introduction to controlling the DIY Fire Fighting Robot 01:35 Building a DIY Fire Fighting Robot using Arduino 02:59 Background music used in the video. 04:03 DIY Fire Fighting Robot using Arduino 06:28 DIY Fire Fighting Robot using Arduino 08:02 Arduino-powered DIY Fire Fighting Robot
Hola yo hice este proyecto es completamente funcional, si no les vale recomiendo que se fijen que sus sensores de flama sean de 4 pines y estén conectados a el pin analógico A veces 2 baterías 18650 no son suficientes a me sirvió adecuadamente con 4 Fíjense si cada cable está donde debe y con el diagrama que adjunta Excelente video me salvó el proyecto final
Hermano yo lo estaba haciendo con sensores con salida digital ahora que dices eso ahora todo tiene sentido muchas grs por el comentario ya que estaba batallando durante un tiempo por eso por qué solamente el servomotor da vueltas y al parecer no veían la llama
Yo creo que toda la gente que dice que no le funciona es por que minimamente no sabe el orden jerarquico de la programación, haré el intento en estos dias, enviaré una confirmación como respuesta :)
Bro i tested by changing the port,when i changed it turns left and then i changed it turns right but the problem is 2 ir was not working for bo motors at the same time if i change the port only one ir was working for bo motors and turning left and right if i changed what to do(two ir was working for pump motor 😐)
Hello! I am making this for my sister's science fair project!! I wanted to know if I can use this water pump: 5v DC Mini Water Pump Micro Submersible Motor Pump 2.5~6V 120L/H
Oyeee mira una pregunta sirven los sensores q son azules pues no los rojos q utilizastes si no los azules con solo 3 palitos en hago entender@@saadinnovativeideas
Connect Arduino's No:10 pin to EnA and so on Upto 5th pin to EnB. Take 3(A0) Pins of Sensors, Servo's Vcc and Arduino's 5v and connect it in a separate column of breadboard. First Connect A4 pin and Servo's PWM pin if it's not working then connect to D11 of Arduino and change the code from A4 to 11. Lastly suggest you that make your own connections one by one from the given circuit diagram it's easy and working.
good work bro,ok now for me am working on my final year project which is about fire fighting robot with obstacle avoidance.For obstacle avoidance am using ultrasonic sensor which is connected with servo, that rotate with ultasonic to sense obstacle left,right and front.Priority is fire but if there is obstacle ,the car should stop and go where there is enough space.How can i do this?
Bro as u told before i changed the code to 1,2,3 like digital output but the problem was the pump motor running automatically can u give the clear explanation or code for that please
No brother it has auto control. It has flame sensors that detects fire and Arduino interprets the signal and perform task as programmed. It doesn’t required any kind of transmitter
he deserve to be banned from yutube for giving saying that this project will work but his code is not working , and he used micro controller for motors and in the circiut i doest been shown fake like pakistan
Hello! I like this video. So my question is this: is it possible that you can add Bluetooth control module so that in case the flame sensors are not in range of detecting fire, Bluetooth can be used to drive vehicle to approach the area of detection. And also Bluetooth can used return back vehicle if water is empty in tank. Thank you
Bro , I am going to make this project and I have ordered all the things as you said in the video does the cod and the circuit work coz some comments says it doesn't work
Bro I have done this project, Then switched on, It was lighting in uno bord and motor controller, I programmed and uploaded, But It was not moving and the servo motor was not working . May I know what would be the problem.please😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢 please please please 🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏
Hello sir I need your help Sir we have made the same problem like our Arduino Uno is not properly working bcz the power does not reach to Arduino What should we have do to resolve it
Saad all the connections r right, arduino, flame sensor and L298 motor give red light when i turn on the switch but the code is not working or i dont know what but nothing works at all, Please help me
All components are working we change the battery also but it doesn't moving ir was light on when switch on everting is light on but it not moving and servo not working but it checked with aurdino codind it's working but in whole thing it not working, so pls reply fast we have only 5 days 😢😢😢😢😢pls
I have one solution for using 3 pin flame sensor, try it Connect A0 of all the sensors with 2,3,4 (digital) pins of the Arduino uno board and in *code* replace A0, A1,A2 with 2,3,4 respectively and replace *analogRead* with *digitalRead* any where written in code
Brother apply same connections as given in circuit diagram. Try this new clear one drive.google.com/file/d/1bFK8Dwt6g-Z2kP-Qzci0NTRzXW0DrkRT/view?usp=drivesdk
@@saadinnovativeideas saad bhai ..agar aapko time mile toh pls breadboard pe bhi connections laga ke image share kardo ..it will help newbies like me :)...btw happy new year ...i subscribed ur channel and also told my freinds to subscribe it ....boht accha kaam kar rahe ho bhai ...waiting for more projects by you :)
You are free to *ask Questions* about any issue regarding this project *(In any language)*
Hi I need to contact you to discuss possible the use of yr idea for the firefighting robot. Can you send me your email ? thanks Claudio Ben
@@saadinnovativeideas rother I only have 3 pin fire sensor will this work?
@@claudioben2060 you can discuss it here
@@saadinnovativeideas Can you explain it further? Sorry I'm very new to coding, just need to make this for my daughters project.
@@saadinnovativeideas analogWrite(enA, Speed); // Write The Duty Cycle 0 to 255 Enable Pin A for Motor1 Speed
analogWrite(enB, Speed); // Write The Duty Cycle 0 to 255 Enable Pin B for Motor2 Speed
delay(500);
}
void loop(){
s1 = analogRead(ir_R);
s2 = analogRead(ir_F);
s3 = analogRead(ir_L);
For example this? Should I replace it with digital?
Bhai ye sach ma kam kar raha hai I am so happy 🎉🎉🎉🎉🎉 thanks bhai
Welcome 🤗
Bhai banaye ho to batado ki 4ro bo motor kese kaam karega
POV: you're here because your teacher asked you to make a project
CCT SUBJECT😭
FR
real
I am here for my international project
00:10 Learn to create an Arduino firefighter robot
01:04 Robot designed to handle fire disasters
01:20 Introduction to controlling the DIY Fire Fighting Robot
01:35 Building a DIY Fire Fighting Robot using Arduino
02:59 Background music used in the video.
04:03 DIY Fire Fighting Robot using Arduino
06:28 DIY Fire Fighting Robot using Arduino
08:02 Arduino-powered DIY Fire Fighting Robot
❤️
Geeat
I like your idea to much ❤❤❤❤❤❤❤❤❤❤
Glad you like it 😊
your project is the best i have ever seen great job
So nice of you
You deserve more brother thank you❤
🤗 😊 ❤️
Dividing a complex thing in simple is art. you have it 🎉
❤️
How you have soo less subscribers and likes you deserve more, keep it up saad
Thanks ❤️ I will get it all with your support
Thanks Saad
It's working very well but only at night not in day light
bro can You please help me , after 2 days I have presentation
Your model is moving? Mine is not moving but motor is working it only doesn't moving... What do you think about this problem? Please reply
@@Alwaysalearner-fn9io Same problem bro
Bro I like your idea really good 😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊👍😊😊😊😊😊👍
oy yes
Thanks 😊
Dont use this video to make this project . His code doesnt work, just because of him i lost my place in a science fair
Gonna use his project only for diagram 😅😂
I recommend don't use this project for circuit diagram also
Yes it is true
@@laxmiprasanna1020 muy tarde lei los comentriosss
@@Md_Rofiqul_Islam-y6rbro can u tell me the code his is not working
Good work my friend!! I made a GPS guided RC car and know the amount of programming you had to do! Nice
Thanks 😊.. GPS based, That’s cool
Wow! Great job
Hola yo hice este proyecto es completamente funcional, si no les vale recomiendo que se fijen que sus sensores de flama sean de 4 pines y estén conectados a el pin analógico
A veces 2 baterías 18650 no son suficientes a me sirvió adecuadamente con 4
Fíjense si cada cable está donde debe y con el diagrama que adjunta
Excelente video me salvó el proyecto final
Thanks bro
Hermano yo lo estaba haciendo con sensores con salida digital ahora que dices eso ahora todo tiene sentido muchas grs por el comentario ya que estaba batallando durante un tiempo por eso por qué solamente el servomotor da vueltas y al parecer no veían la llama
Me podrías ayudar con algunas dudas que tengo
Excellent work saad ...
Proud student 🎉
Keep it up ...
🎉🎉🎉🎉
Bundle of thanks brother for your support and appreciation ❤️
اخويا الطرش ❤
جامد ي غالي🔥♥️
ههههههههههههه
Thanks brother ❤️
Yo creo que toda la gente que dice que no le funciona es por que minimamente no sabe el orden jerarquico de la programación, haré el intento en estos dias, enviaré una confirmación como respuesta :)
Will be awesome. Thanks
@@saadinnovativeideasBro it works 👌🏻
@@Os.Pinto.R como lo hiciste
yo lo he hecho pero el carro no avanza
@@Minmin-di5zplo copiaste y pegaste tal cual al arduino ide?
The flame sensor diagram is different to the one in video please tell what to do
😢
Help me
I have showed flame sensors circuit diagram in the video follow that
Which transistor we use in the place of tip 122 because it is not available
Hi cute Saad keep up continue the spirit ❤❤
Thanks brother.. Inshallah I will
Bro i tested by changing the port,when i changed it turns left and then i changed it turns right but the problem is 2 ir was not working for bo motors at the same time if i change the port only one ir was working for bo motors and turning left and right if i changed what to do(two ir was working for pump motor 😐)
3:29 why did you not solder ground in the module bro
It's really amazing. Best of luck ❤️
Thanks a lot 😊
Hello!
I am making this for my sister's science fair project!!
I wanted to know if I can use this water pump:
5v DC Mini Water Pump Micro Submersible Motor Pump 2.5~6V 120L/H
Yeah thats suitable..
Oyeee mira una pregunta sirven los sensores q son azules pues no los rojos q utilizastes si no los azules con solo 3 palitos en hago entender@@saadinnovativeideas
Thats compatible for this circuit diagram and code if that have *A0* pin
hjunh
Where we get all of these things pls any1 tell material names
great broo you help me a lot.
Happy to help
Thank you for this video ❤
We are going to make it.
Lets hope that we will get sucess
Did it work?
@ma.alneyadi44 nah
We got second prize in science exihibition
But it worked only in dark place. It doesnt worked in light place.
WELL DONE BRO!
Connect Arduino's No:10 pin to EnA and so on Upto 5th pin to EnB.
Take 3(A0) Pins of Sensors, Servo's Vcc and Arduino's 5v and connect it in a separate column of breadboard.
First Connect A4 pin and Servo's PWM pin if it's not working then connect to D11 of Arduino and change the code from A4 to 11.
Lastly suggest you that make your own connections one by one from the given circuit diagram it's easy and working.
Didn't understand the 3rd point
@@ansu.officialbro I've done the same as he did now I need help what should I do now
@@almanmemon6676 I mentioned few changes, try it !
I also want your help @@ansu.official
@@ansu.officialmy only servo is working rest all part will not work
Can we use flame sensor MODULE other than flame sensor
Yeah they are same
We are gonna working on this for school project
@@CricketCraft-56 i m making this too
@@SadanAnsari01Kiya AP ka challa
have u connected the wires that you are showing, which inserted in breadboard(have u connected them or just inserted into braedboard???)
Brothers breadboard have internal parallel connection and work as an extension for pin inputs. Study about breadboard a little
Here I leave the code that I used, my Arduino is a Chinese one, it is the ch 340G and
#define enA 10//Enable1 L298 Pin enA
#define in1 9 //Motor1 L298 Pin in1
#define in2 8 //Motor1 L298 Pin in2
#define in3 7 //Motor2 L298 Pin in3
#define in4 6 //Motor2 L298 Pin in4
#define enB 5 //Enable2 L298 Pin enB
#define ir_R A0
#define ir_F A1
#define ir_L A2
#define servo A4
#define pump A5
int Speed = 160; // Write The Duty Cycle 0 to 255 Enable for Motor Speed
int s1, s2, s3;
void setup(){ // put your setup code here, to run once
Serial.begin(9600); // start serial communication at 9600bps
pinMode(ir_R, INPUT);// declare fire sensor pin as input
pinMode(ir_F, INPUT);// declare fire sensor pin as input
pinMode(ir_L, INPUT);// declare fire sensor pin as input
pinMode(enA, OUTPUT); // declare as output for L298 Pin enA
pinMode(in1, OUTPUT); // declare as output for L298 Pin in1
pinMode(in2, OUTPUT); // declare as output for L298 Pin in2
pinMode(in3, OUTPUT); // declare as output for L298 Pin in3
pinMode(in4, OUTPUT); // declare as output for L298 Pin in4
pinMode(enB, OUTPUT); // declare as output for L298 Pin enB
pinMode(servo, OUTPUT);
pinMode(pump, OUTPUT);
for (int angle = 90; angle = 40; angle -= 5) {
servoPulse(servo, angle); }
for (int angle = 40; angle
@@leonardougarte1173 are you a saint?
@@leonardougarte1173tq🎉
@@leonardougarte1173hey
@@leonardougarte1173 i am making this too
good work bro,ok now for me am working on my final year project which is about fire fighting robot with obstacle avoidance.For obstacle avoidance am using ultrasonic sensor which is connected with servo, that rotate with ultasonic to sense obstacle left,right and front.Priority is fire but if there is obstacle ,the car should stop and go where there is enough space.How can i do this?
You have to modify arduino code by addition to ultrasonic sense. And circuit diagram will also differ by little
Bro can you please share your project if you have made
me too can we talk about it ?
@@NajmAl-hokabi yes I have already completed this project last year
@Brightwillehosea please how can we contact you?
Bro as u told before i changed the code to 1,2,3 like digital output but the problem was the pump motor running automatically can u give the clear explanation or code for that please
If you turn it on in the sunlight it won't work
Battery to switch connection there will be short circuit how to correct this problem and the code is not uploading
Una pregunta si los sensores y la bomba de agua funcionan bien pero los motores no se mueven que error podría tener?. Buen video
Mostly power source (battery) problem
that is very good
Get unstoppable saad!
Well done!
Thanks 😊
getting exit status 1 error while pasting the code from description, can you please help
OMG I love it I'm making it for my project ❤❤
hey saad. im going to buy arduino and other parts for this so are you sure that it works good? like code and everything
It works as shown in the video. Yes code and everything is fine. If you found any problem let me know I will try to solve
@@saadinnovativeideas hermano encontre un problema, respondeme si estas dispuesto a arreglarlo
Well-done saad
Thanks 😊
very nice I ju st got dianose with diabetes but now im good
what dose that mean? 😅😅😅
Hi! We already completed the process and followed the exact materials used. Yet, ours is not working. What could gone wrong? Thank you.
Please, help us. It is urgent and for our project.
Thanks for your video as my team got 3rd prize in digital fest
Congrats 🎉
Does it works please tell me i am going to make itt
@@MADARANARUTO7 did you made it?
@@SadanAnsari01 brother its not working at all
can i ask?
could you please help me write the arduino code for the bottle labeling machine, Thanks in advance for your reply.
Love form Bangladesh 🇧🇩🗣️💙
❤️❤️
Very good
❤️
Genial proyecto !! Gracias por compartirlo 😊
Glad, you like it
This is a good idea...Brilliant i must say
So nice of you brother. Glad you like it
Does it require any bluetooth or wifi connection or it can run independently onto to extinguish the fire?
No brother it has auto control. It has flame sensors that detects fire and Arduino interprets the signal and perform task as programmed. It doesn’t required any kind of transmitter
Good Work Bro…❤️
Keep the spirit on🤍
Thanks .. I will 😊
do all use jumper wires? pls give me the answer as soon as possible
??
Can we connect as shown in the circuit directly 🙏😞 say
Yes
Man u disserve to be subscribbed for ur talent
Thanks a million brother for your support and precious wordings
he deserve to be banned from yutube for giving saying that this project will work but his code is not working , and he used micro controller for motors and in the circiut i doest been shown
fake like pakistan
@@RISHIT-eu8ck wowww
@@RISHIT-eu8ckCheck your connection And contact with psychologist
only just make some changes in the code thats it. then you're amazing...
Please tell me what changes u made
Please help me
I did not do any. Asking him to make changes
@@pokala8806 what changes
Great guider!
I just didn't get yet the meaning of "Chachies" in your materials list. which component is that? tnx
The white coloured sheet in the video on which the components are stuck
Cool 😮
How to increase the pressure of the water that is coming out of the nozzle?
Use tube (pipe) of small diameter or use strong motor
Good job, keep it up.
The code is not in the discretion
Sorry I was going to upload it in two days. Check it again a day after tomorrow… thanks
Hi bro I did the project same as in video but the robot is moving back instead of moving front what should I do..?
You may have confused the positive and negative poles of the wheel motor or wired it backwards when connecting the wheel motor to the L298N
It should not move backward
Change the motter wire
make reverse connection
You should give opposite supply of electricity
So in short no smoking anymore?
sadly yes my friend :(
I don't have IN4148 diode what happens if I don't use it plz answer sir
Hello! I like this video. So my question is this: is it possible that you can add Bluetooth control module so that in case the flame sensors are not in range of detecting fire, Bluetooth can be used to drive vehicle to approach the area of detection. And also Bluetooth can used return back vehicle if water is empty in tank. Thank you
Yes it is possible and I may built it and upload its video in future
Can you give it for me c'se I wish to work on it as my academic capstone project
What I can give you?
How can I get the video with Bluetooth module as additional controller
7:16 what is that
Hard jumper wire
Bro can I use normal wire
Please give me a ppt file of this project.
Bro , I am going to make this project and I have ordered all the things as you said in the video does the cod and the circuit work coz some comments says it doesn't work
Plz reply...😢
Yeah it will work but depends on you and the way you make and upload the code. I mean if you do the same I showed
Ok
Is it ok if I use a lithium - iron battery for this project
Sorry I don’t know about lithium-iron battery. If you mean lithium-ion, yeah that are perfect to use
Guys, for who all dont know where the code is, go to description and click on the google drive link
Bro can u pls help with connections of ln driver and arduino as if im giving power one side is working another is not
Bro I have done this project,
Then switched on,
It was lighting in uno bord and motor controller,
I programmed and uploaded,
But It was not moving and the servo motor was not working .
May I know what would be the problem.please😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢 please please please 🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏
Which battery and sensor you have used?
Three pin sensor with li ion battery
The code if for foir pin sensor having analog pin A0. You have yo change analog funtions in code with digital functiona
Brother or else shall I change the sensor
Or please give me the detail coding
Hello sir
I need your help
Sir we have made the same problem like our Arduino Uno is not properly working bcz the power does not reach to Arduino
What should we have do to resolve it
How much voltage have you given as an input to the arduino board and with which pin of board have you connected the positive terminal of battery?
The same thing was happening to me you should power the arduino by the port of 12 v
Should I have to connect the 5V pin of Motor driver to anything.
In this connection the motor driver is turning on.. Not showing red light
bro, how do we get the pin out of the female jumper wire. Do we do it using a tweezer or something, cuz I am not able to understand.
You wanna make male to female from female jumper. Yeah use tweezer to remove the cover and cutter to replace pin
Arduino ki koi library bhi install krni padegi kya project run karane ke lie pls reply 🙏🙏🙏
Nahi
Very nice and super❤❤❤❤😊😊😊😊🎉🎉🎉🎉😁😁😁😁
❤️
Will u please provide the code ?
Check it in the description
@@saadinnovativeideas?...
Check it now
@@saadinnovativeideas thank you 😊
Tq sir
My bo motor and servo motor is not moving im using 3 pin fire sensor please help me please
Your sensor has do(digital output) connect this pin to the digital pic of uno and change the code analog to digital
There should be light in the sensor
Saad all the connections r right, arduino, flame sensor and L298 motor give red light when i turn on the switch but the code is not working or i dont know what but nothing works at all,
Please help me
@@ayushsrivastava8580 any solution?
Yeah same problem occured with my project, if you found the problem, Can you please tell me what is it?
@@Unknown._369 same problem...give solution plz
@@ayushsrivastava8580 you need to add library in computer software
Which library @@SadanAnsari01
@saadinnovativeideas Great work 🎉
But can i use more flame sensor at back of the car
Yes, I think so and I may do it in future
U are so cool ❤
😊
My project Wark
brother will using 12 volts water pump with 11.1 rechargable lithium ion 18650 fry out the sensors or the servo because it only operates in 5v?
But the motor driver regulates the servo, sensors as well as bo motors voltage to the desire value
wow 👏👏
I bought 3 pin flame sensor, it does not have AO port, what should I do?
tomorrow is science expo pls reply
Lol
How to buy it
Not for sale!
@saadinnovativeideas cost of components
You will get all the components at *25-30 $*
@@saadinnovativeideas ok
code is fake
Then can u share me the right code
Sir arduino ki koi library bhi install krni padegi kya project work karane ke lie pls reply🙏
All components are working we change the battery also but it doesn't moving ir was light on when switch on everting is light on but it not moving and servo not working but it checked with aurdino codind it's working but in whole thing it not working, so pls reply fast we have only 5 days 😢😢😢😢😢pls
Me too
Me too please reply fast
Same problem, what you have done to work?
Bro can i use 3 pin flame sensor pls give me answer because after 10 Day I will show my project
The circuit diagram and code is for analog pin flame sensor (4pin )
Appreciate your work brother 🥰
And can you try to give me a tutorial or circuit diagram for that 3-rod flame sensor pls reply fast
I have one solution for using 3 pin flame sensor, try it
Connect A0 of all the sensors with 2,3,4 (digital) pins of the Arduino uno board and in *code* replace A0, A1,A2 with 2,3,4 respectively and replace *analogRead* with *digitalRead* any where written in code
Can I interchange the position of the wires of the flame sensors while connecting on the bread board.
No
Mashallah❤❤❤
Jazakallah❤️
Creative video, thanks :)
Wlcm
Do I need to know about flame intensity using the IR flame sensor?
IR 4 pin Flame sensor
It will not short circuit right if i dont use resistor, transistor and capacitors
The pump will work properly. You can use relay module instead of these
How much current should I save?
Is 11.1 volts and 2 amps enough?
Yes enough
saad bhai pls help ...pls give me circuit diagram in which breadboard connections are also present ..thanks bhai
Brother apply same connections as given in circuit diagram. Try this new clear one drive.google.com/file/d/1bFK8Dwt6g-Z2kP-Qzci0NTRzXW0DrkRT/view?usp=drivesdk
@@saadinnovativeideas saad bhai ..agar aapko time mile toh pls breadboard pe bhi connections laga ke image share kardo ..it will help newbies like me :)...btw happy new year ...i subscribed ur channel and also told my freinds to subscribe it ....boht accha kaam kar rahe ho bhai ...waiting for more projects by you :)
Thanks bhi for praise and efforts.. Lekin mene apko bataya ke bredboard pr bhi yahi connections krne hai simple hai bs circuit digram ko dek kr katlo