Recover Quad/ Dirt Bike, Snowmobile Seat in one hour DIY for $25

Recover Quad, Dirt Bike, Snowmobile Seat DIY for $25 - All the tricks in one video. Ive been fixing up bikes since the 1980's and done this many times. Tools Needed- flat screwdriver, pliers, sharp long bladed knife, heat gun or hairdryer, angle grinder and any rough open type disk.staple gun. scisors, marking chaulk or removable pen, Materials- High temp spray glue, Gap filler foam aerosol, thin foam sheet 6-10mm, Marine grade vinyl
Check out my Land Rover rebuilds and camp outs www.youtube.co....
Living the off Grid, Lifestyle, living big in a tiny house, tiny house on wheels, small house, tiny house design, tiny house tour, overland trailer, teardrop, squaredrop, restoration, rust repair, green roof, living roof, green wall, tiny house, new zealand, tiny house architecture, small space design, tiny house living, mother daughter tiny house, tiny house, tiny home, tiny house life, woodstove, wood fire cooking, composting toilet, bio digester, biogas, self sufficiency, permiculture, rainwater, harvesting, Landrover, series 3 stage 1 110 88 109 off road, Housetruck, space saving furniture, dream tiny house, modern tiny house, modern home, eco home, small home tour, tiny house 2020,

[@wyattcalton2438]

You had the same ideal as me brotha. I fixed several seats with this method.

[@Smurphenstein]

Better to use that upholstery foam in the background, cut around the areas of damaged foam so it has straight edges and replace with new. Then warm the vinyl in the sun and stretch it over the repaired foam using a hair dryer. Expanding foam won't give until it collapses and doesn't retain a good memory.

[@daddyvet478]

Upholstery foam is not nearly rigid enough. But I don’t think this is the right material either. I’ve tried to Upholstery and it’s basically like sitting on the seat without any foam

[@lmt-adventures620]

Good work! Got one with just plastic left. Foamed the whole thing and after it dried it shaped it down and now looks brand new.

[@LoneScout1]

Thanks for sharing mate, gives one the perseverance that is required to pull things off, from a seadoo seat re-cover to a classic whatever one’s got

[@richperkins5192]

Thanks brother.

[@stacyreid5077]

PS you did a great job with the seat and tutorial on seat covers 👍🏻👍🏻

[@mthangar]

Man of many talents. Well done

[@handyhippie6548]

only problem i can see with this is spray foam is rigid, and not very springy. once it is crushed, it will be lower in that spot. i usually use old couch cushion foam to refoam seats. the foam anti fatigue floor mats are a good source of cheap, denser foam for places when you need more support, and less squish.

[@carminecarlone2869]

So how do you attach those foams to the seat? I need to do something similar on a bike I got

[@handyhippie6548]

@@carminecarlone2869 i use 3m spray glue. just follow the instructions on the can. you can find cheaper spray glue, but since it is something you only want to do once, it's worth using the best. an old electric carving knife is the easiest way to shape the foam.

[@wyattcalton2438]

You don't notice it. And once covered up out of sight out of mind.

[@stacyreid5077]

My mom and I recovered the seats on my SXS about 7-8 years ago with marine grade vinyl and thread 🧵 but last summer the thread started coming apart once it started sitting in the weather more , that plus my big dogs 80lbs & 120lbs started to sit in the seats.

[@AliMackMechanical]

What a really clever way to do it mate. Thanks av got a quad bike seat I need to do you helped with I can do it now.👍

[@benkaminski3876]

Great job teaching very informative

[@t.h.o.r.]

Thanks Ben. Ive been doing this for years. Despite what the anti spray foam people say- It works and it lasts. Ive fixed dozens and dozens of seats

[@LoneScout1]

In the case of my Seadoo seat, with a lateral crack across the seat foam but no actual gaps…that a spray adhesive would be better than a spray foam as there is no gap to fill.

[@momoloo141]

Nice work, what kind of spray foam would you recommend? I restored several seats, but they had no deep holes, so I shaved them down and upholstered them with a layer of thin foam. Also you didn't use glue for the vinyl before stapling. I will definitely try this the next time, too. Thanks for your input 😁

[@t.h.o.r.]

Yes never glue the vinyl- It needs to move to stretch to fit

[@steveeisenhauer3003]

Looks good to me!

[@timfitzgerald1696]

You're too smart mate!!!!!!

[@richardburgers8965]

Does the spray foam have some softness to it? Just wondering if you notice any difference between the 2 foams. Thanks. Nice video

[@t.h.o.r.]

Oh absolutely!- Its not touring bike soft though. Its the best Ive found for the job. Its fine for MX Enduro and farm quads. Ive done these repairs for decades now and never had a complaint

[@gallopingg1]

BRILLIANT JOB, UK

[@TheCbj79]

Can you fit it in the back there whit out the sewing? I have a hard hard seat that i bought repros for. But i can get the curls away in the back going incane doing this, Can you show if you hav a trick for that a almost llike a 3.5cm middle look like a smile in the back squear tho corners are about 4.5cm squear seller says it's easy. But no... there is streatch in it both ways but i think to thik

[@BudgetRC_Channel]

The spray foams that I've tried dry hard and if you compress it, it stays compressed with no rebound. Is the spray foam that you used more compliant?

[@davidedala4739]

I think u made a mistake because that type of foam doesn't go back to the original shape once is compressed..

[@999benhonda]

To those saying the spray foam will be hard, that is true of every brand ive ever used...however, the hard ones can't be cut that easy with a knife. That brand he uses must be a different formula

[@t.h.o.r.]

after trying 4 brands I settled on this one. Ive done many many quad bike seats car seats jet ski seats, dirt bike seat repairs and modifications with great results. Thanks so much for your comment Ben.

[@michaelannen4168]

This foam turns to powder when compressed

[@charlys1219h]

Great video but not Great job
You could do a top stitch on the back and put another layer of padding to disguise the foam repair !!
Also all depends how much did $ changed 🤔..
I considered that too 🤫

[@chriskenny6520]

I hope the front stays on🤞

[@hughstratton8767]

Great job other than it must be painful to sit on

[@t.h.o.r.]

Whaaaaat!?- it feels just as it should- I explained that this particular brand of foam is perfect for the job!
If I was doing a crap job people would not bring me seats every week! sheesh! give people a keyboard and they become instant experts! lol.

[@digschopper9321]

I think what he means ,at least here in the States,is the only expanding foam is rigid. If I could find expanding soft foam,I'd be ecstatic.

[@modoc852]

First time aye

[@TheRadioStu]

Outside the environment 😂

[@t.h.o.r.]

Oh yes- I never dump stuff in the environment 😬😆

[@robertmorris7998]

NOOOOO! TAKE IT TO A LOCAL SHOP AND GET IT DONE RIGHT!!!!!!