What I did to fix mine (so far it’s worked 2 days) is take as many screws out of the motherboard as you can and pry on the side gently while tucking in tightly folded paper shims. There was another video where somebody took out the motherboard and put electrical tape on the back as a shim but my screwdriver hates half of the screws in that phone.
Nice vid... one problem... You must never connect the screen with the battery plugged in because you can blow the caps the feed the drivers for the screen..
I watched many videos before but this is the best by far...thou im a bit disappointed since most of your videos show teardowns and other stuff than level three repairs. Please show more level three repairing pls pls pls....
i had my phone fixed, however it becomes unresponsive after a few minutes. i had to bring it back to the tech 3 times but to no avail. is it really possible to recur even after a few minutes only? any advise?
Hi, to repair the IC, you should get a solder iron which should be temperature-controllable, because the temperature should reach to 350-400 centi degree
If we sell a iphone whose battry is dead and is struck on boot loop with all the apple id and phone password with it..will the new owner can access my data?
Hello Sir! My iPhone's problem is that, I couldn't turn it on, can't do hard reset and can't read my device in itunes.. It's been 5 days since it experienced boot loop. What's the main problem of this? Help me
you have to start somewhere, so you start by reballing touch ic, if not then you move to next and so on. Its like, if a car wont crank at all, what you would do? check battery, same as with this Touch IC problem, reball Touch IC first.
There is a schematic and motherboard layout for iphone 6p that show you the connected circuits and points, so all you have to do is follow the paths between points and measure them by multimeter to detect the damage.
Hi, Iphon6 CPU chip ic has broken due physical damaged , possible to repair n take a back up from phon. I need ur help to repair my iphon or get data backup Please help me on urgent basis Waiting for your response Also, please let me where can I send my phon for repairing
Cryo Phantasm I’d say your best bet is taking it to a repair store to have them look at it if you haven’t already. Most places in my area don’t do board level repairs, but the place I work at along with the other store in town uses a guy that does microsolder work that receives business from all over the southeast
@@EricWitrigs my friend can you please tell me something, when you initially clean the PCB when you remove the IC , you use solder iron with Heat gun why is this ? because of lead free requiring too much heat on the board so you are using soldering iron + heat gun ( I don't have clear what temperature on solder iron and what temp on heatgun and wind speed please I have quick861dw) . When you desolder and solder back again heat gun wind speed please, also if I use a 45 degree nozzle do I have to give more air speed?
Professional work but there is one problem. The mechanic didnt apply adhesive tape before sealing back the lcd to the phone. Even the phone lost its waterproof resistance, at least the adhesive tape will protect the phone from dusts and small amount of water from entering it
@@cris90716 Apple added lcd adhesive starting from 2015 iPhone6(s) generation, what makes you so sure that iPhone 6 plus has stocked adhesive? I have an iPhone 6 plus before and was bought new directly from the apple store, I opened up the phone before for a battery replacement as battery degrades overtime and never see any adhesive. Telling others stupid without a solid proof makes you even dumber man
The cool Jordanian kid at Kenwood mall Cincinnati Ohio is the iPhone beast.. sam... called quick I phone repair..hes just past Apple scammer store where on any given day 50 people are standing in Apple with screwy iPhone issues and the Apple tech fake looks at phone he will just blurt out a random dollar figure well this being the 4th visit he says ahhh 129 bucks i can get to it by appt in 2hrs.. i walked out past the 50 to 70 repair customers and went over to the kiosk in mall the kids a wiz he fixed it in 11 mins flat for 15.00.. amazing what a few compatible screwdrivers n aluminum replacement parts do
most time fixing this problem is using original follow come screen and the touch will work one time. iPhone 6 plus do not support china screen most time.
Hi, Greetings from India! 🇮🇳 Last week i accidently dropped the upper part (earpiece & camera area) of my iphone 6 into water. It was only after a week that i could take my phone for repair & the technician told me the exact same problem addressed in this video of a faulty display & touch ic and charged INR 4100/- ($ 63) for repairing the same. The battery was 57% when he handed me the phone and within 45 mins. the phone's battery got dead and now its not even charging at all, i've tried a different charger as well but the phone is like dead. Now, i know that the device is not in front of you, but with your experience can you please help me out with the following : a. Was i overcharged for the touch ic & screen replacement which is a first copy & not original apple? b. Was there a need of replacing the screen as well or just rectifying the touch ic would have done the trick ? c. Why was there such a huge power drain & now the phone is not charging at all, it's like dead. Is it because of or connected to the screen & touch ic replacement? d. How can i get this fixed at minimum possible cost & approx how much would it be ? I have already spent alot on an old phone and I don't wish to spend more. Your help will be highly appreciated. Thanks in advance. 🙂 P.S. - In the 10 mins. that i tested the device post repair - the earpiece, microphone, camera, network signals & calls ( both in & out) were all working fine.
$63 is a GREAT price to have this done. The guys that do these have to be very skilled and require expensive equipment. Apple charges $149 and thats not even a bad price and they guarantee their work. How old is your battery? Have you tried different charging cables and power supplies? It's more than possible that the repair shop made a mistake, and for that price Im not surprised. Go back and offer them INR 1600 to figure out what they missed. Only the guy that did the repair will know which, if any, of the steps in the video may have not gone smoothly. If they dont do it then you should sell it for parts and buy a new phone.
I actually bought a cheap heatgun and got the tools to open the phone but the UV light stuff and the template he used are nothing you easily find... I might just try heating up the chip so whatever caused the problem gets reconnected.
Hello mere pass iPhone 6plus Hai usme touch problem Hai agar thodi Der rek dete Hai to touch thodi Der chalthi Hai Varna Nahi soulstion please ? Folder ki bhi Kami Nahi Hai mene r badal keep dekha that may whatapp v contact number. 8958111682 please solutions
هذه قناة رائعة! إنها الآن إحدى قنواتي المفضلة. تعجبني كثيرًا
Very Good work and teaching sir
Great video. I don't think I could ever do that, but really interesting to watch!
Colegas alguem tem o video mostrando o meson no iphone 6 S Plus. Parece muito diferente do 6 plus
I know this place won't get answered but for tin paste do you use sodering paste
What I did to fix mine (so far it’s worked 2 days) is take as many screws out of the motherboard as you can and pry on the side gently while tucking in tightly folded paper shims. There was another video where somebody took out the motherboard and put electrical tape on the back as a shim but my screwdriver hates half of the screws in that phone.
Nice vid... one problem... You must never connect the screen with the battery plugged in because you can blow the caps the feed the drivers for the screen..
Sucks it's not working my iPhone 6 cannot touck every second I wish someone can make a video to make it work
Kevin Lopez mine too. Did you went to rrpair shop?
i have connected screen with the battery plugged in and now my touch is not working, what is the solution
8:32 Chinese repairer. “好助手” is written on the solder paste
Thanks you for you videos it help alot
i have esy solotion
what size you using solder wire
Thanks for this Video Guy🙏
I watched many videos before but this is the best by far...thou im a bit disappointed since most of your videos show teardowns and other stuff than level three repairs. Please show more level three repairing pls pls pls....
Super , nice video
I phone 6s display back light solution video pls
well explained and good subtitles
Step 1: Be Asian
Step 2: ???
Step 3: Fixed
i am starting, this video help me so much bro
It looks like i can do it then
Loooool
Hello which temp do you set on the solder iron to clean and solder the pads ?
Hi, you could find the temperature at 2:30
Hey there, cool video. I have a question. What is the board called that you put the touch ic into at 13:17?
i had my phone fixed, however it becomes unresponsive after a few minutes. i had to bring it back to the tech 3 times but to no avail. is it really possible to recur even after a few minutes only? any advise?
Why you disconnected the battery last instead of doing it first to avoid short circuits
There have two touch ic s how to find which one is bad ?
Excellent video with very details ! I like and inscriteted in your channel !
Yeah
P
Thanks for the great lesson. I will test it on one unit i have ..Best Regards..Tienda Punto-Movil
Great work
Bro thank you it's working. 😍😍
Very hard worker
Hello sir can I know the model of microscope which u used in this video thank u
I just used a bit of tape that was 2 years ago and still it works perfect and only took 10 mins
how did you do it? i have the same problem :C
did you use a normal tape
@@vickiemuringo1409 it is Working fine with normal tape
@@vickiemuringo1409 No electrical tape
hi after touch ic repair my iphone 6 has battery drain issues. any advice as to why?
117johnA I have the same problem as yours but after I repair my iphone 6 it went back 😔
Your touch ic has a short circuit .Again reball ic
Would a normal solder iron work ? Does it need to be a microsolder iron
Anthony Perry you having this issue
jevone barrett what
Hi, to repair the IC, you should get a solder iron which should be temperature-controllable, because the temperature should reach to 350-400 centi degree
Wit Rigs must it be one of those tiny microsolder irons, though ? A normal temperature control solder iron will work, yes ? That's what I bouggt
Well you need that heat blower too...
Do you do this repair and if so how much do you charge?
When I got mine done it was €100
what is pcb water? i looked every where with no solution
Solder flux
Easy way, Before adding jumper (bus wire ),You should check continuity between U2402-M1 & U2403-1, If It 's Okay , Don't need to do that !
Fantastic work
ok thanks
great work
If we sell a iphone whose battry is dead and is struck on boot loop with all the apple id and phone password with it..will the new owner can access my data?
Same has problems in my mobile 6 plus how can i fix it
i just love this background music 😍
me too
Nice work sir thanks
Can i use parts of my Iphone 5 to fix it?
Thank you
very nice work
Did you wrap anything around the soldering tip?
If so, what was it
It’s getng white lines only some times .. if we use like that only somedays .. we will get any prblm.. to my mobile
Plz aap batao me kis se repair karwau ise
great job
Thank lot bro
Good very good work
Hello Sir! My iPhone's problem is that, I couldn't turn it on, can't do hard reset and can't read my device in itunes.. It's been 5 days since it experienced boot loop. What's the main problem of this? Help me
WOW. This is work of art! I would like to send you my 6p for repair. Where are you located?
Yeong Cham my phone same problum I want to problum solution so please help me contect me
I want repair iphone 6 plus
Bro plz help me my iphone 6 watar demag ho gya he bus uski screen kaan nahi kar rahi he or to pura phone on ho raha he
How much do you charge iPhone 6 plus
Can pls share IPhone 6s U2 IC repair guide ..
how do you know which circuit is damaged?
lol Cause we got a professional iPhone repair guy who knows iPhone even better than his own body
lol awesome! but so there's no obvious indication you can see?
you have to start somewhere, so you start by reballing touch ic, if not then you move to next and so on. Its like, if a car wont crank at all, what you would do? check battery, same as with this Touch IC problem, reball Touch IC first.
There is a schematic and motherboard layout for iphone 6p that show you the connected circuits and points, so all you have to do is follow the paths between points and measure them by multimeter to detect the damage.
a solder pad was missing..which shouldn't be when the IC was removed..so the connection had to be renewed..
am in zimbabwe i wish there could b someone like u trying to fix my fon .....it z nt touching
Hi bro temperature ????
nice vidéo
Hello sir I have same problem
Nice
Cost ?
nice.
Good !!!
dont have the tools for this so guess I deliver it to someone can do it
Hi,
Iphon6 CPU chip ic has broken due physical damaged , possible to repair n take a back up from phon.
I need ur help to repair my iphon or get data backup
Please help me on urgent basis
Waiting for your response
Also, please let me where can I send my phon for repairing
sorry, We only sell mobile phone repair parts, you can contact the local repair shop
My prob right now 😑
But I don't know.
👍👍👍👍👍good
it's a very slow... fingerprint and camera ic is disabled
I got the chip off but how do I get the chip back on ?
In 8:30, step 4 will tell you.
Please zoom video ..
Mera i phone 6 on nh oh rahi hai yrrr pizz help me bhi
My ip 6plus problem. When i play game mobile legends or pubgmobile. Auto out from game. Because lagging
I dont know how to fix it. I try and try. But cannot
i followed these steps but now the iphone doesn't even turn on anymore at all
how can i fix that?
You may have damaged the board worse or shorted it out by disconnecting the screen before the battery
@@cgoins1993 is there nothing i can do?
Cryo Phantasm I’d say your best bet is taking it to a repair store to have them look at it if you haven’t already. Most places in my area don’t do board level repairs, but the place I work at along with the other store in town uses a guy that does microsolder work that receives business from all over the southeast
Maybe your phone is now dead
Can I send you by mail my motherboard may be u can fix it
School boy error having battery connected before the screen. Great job though :)
I noticed that
Apse baat karni he
can u fix my pliz :@
Hi, is there any problem with that tutorial? Or does it look difficult to do that?
@@EricWitrigs my friend can you please tell me something, when you initially clean the PCB when you remove the IC , you use solder iron with Heat gun why is this ? because of lead free requiring too much heat on the board so you are using soldering iron + heat gun ( I don't have clear what temperature on solder iron and what temp on heatgun and wind speed please I have quick861dw) . When you desolder and solder back again heat gun wind speed please, also if I use a 45 degree nozzle do I have to give more air speed?
super bro
How much?
some points missing....
Most watch this video to. Steal with the eye. Great info.
Sir mobile same problem
👍
❤
I need him to fix my phone.
Over heating
Phoneky subpart khol ke dikhao video mein
Professional work but there is one problem. The mechanic didnt apply adhesive tape before sealing back the lcd to the phone. Even the phone lost its waterproof resistance, at least the adhesive tape will protect the phone from dusts and small amount of water from entering it
Apple didn’t start using adhesive until the 6s models. The normal 6 plus doesn’t even come stock with adhesive
You’re stupid AF iPhone 6 Plus does come with screen adhesive
@@cris90716 Apple added lcd adhesive starting from 2015 iPhone6(s) generation, what makes you so sure that iPhone 6 plus has stocked adhesive?
I have an iPhone 6 plus before and was bought new directly from the apple store, I opened up the phone before for a battery replacement as battery degrades overtime and never see any adhesive.
Telling others stupid without a solid proof makes you even dumber man
The cool Jordanian kid at Kenwood mall Cincinnati Ohio is the iPhone beast.. sam... called quick I phone repair..hes just past Apple scammer store where on any given day 50 people are standing in Apple with screwy iPhone issues and the Apple tech fake looks at phone he will just blurt out a random dollar figure well this being the 4th visit he says ahhh 129 bucks i can get to it by appt in 2hrs.. i walked out past the 50 to 70 repair customers and went over to the kiosk in mall the kids a wiz he fixed it in 11 mins flat for 15.00.. amazing what a few compatible screwdrivers n aluminum replacement parts do
Aire bro ?????
most time fixing this problem is using original follow come screen and the touch will work one time. iPhone 6 plus do not support china screen most time.
who even owns ANY of those tools?
Cost 2k pesos for the repair.
Get Original Replacement Parts For iPhone 6 / 6 Plus ： witrigs.com/en1zh
Hi, Greetings from India! 🇮🇳
Last week i accidently dropped the upper part (earpiece & camera area) of my iphone 6 into water.
It was only after a week that i could take my phone for repair & the technician told me the exact same problem addressed in this video of a faulty display & touch ic and charged INR 4100/- ($ 63) for repairing the same. The battery was 57% when he handed me the phone and within 45 mins. the phone's battery got dead and now its not even charging at all, i've tried a different charger as well but the phone is like dead.
Now, i know that the device is not in front of you, but with your experience can you please help me out with the following :
a. Was i overcharged for the touch ic & screen replacement which is a first copy & not original apple?
b. Was there a need of replacing the screen as well or just rectifying the touch ic would have done the trick ?
c. Why was there such a huge power drain & now the phone is not charging at all, it's like dead.
Is it because of or connected to the screen & touch ic replacement?
d. How can i get this fixed at minimum possible cost & approx how much would it be ?
I have already spent alot on an old phone and I don't wish to spend more.
Your help will be highly appreciated. Thanks in advance. 🙂
P.S. - In the 10 mins. that i tested the device post repair - the earpiece, microphone, camera, network signals & calls ( both in & out) were all working fine.
A reply would be much appreciated..
$63 is a GREAT price to have this done. The guys that do these have to be very skilled and require expensive equipment. Apple charges $149 and thats not even a bad price and they guarantee their work.
How old is your battery? Have you tried different charging cables and power supplies?
It's more than possible that the repair shop made a mistake, and for that price Im not surprised. Go back and offer them INR 1600 to figure out what they missed. Only the guy that did the repair will know which, if any, of the steps in the video may have not gone smoothly. If they dont do it then you should sell it for parts and buy a new phone.
Omg i cant do that
I actually bought a cheap heatgun and got the tools to open the phone but the UV light stuff and the template he used are nothing you easily find... I might just try heating up the chip so whatever caused the problem gets reconnected.
This the way of solving the touch screen issue some of bast*rd youtuber make people fool showing nonesense video.
Hello mere pass iPhone 6plus Hai usme touch problem Hai agar thodi Der rek dete Hai to touch thodi Der chalthi Hai Varna Nahi soulstion please ? Folder ki bhi Kami Nahi Hai mene r badal keep dekha that may whatapp v contact number. 8958111682 please solutions
This means don’t try this at home.