Это видео недоступно.
Сожалеем об этом.
Nintendo Switch SD Card FPC Replacement
HTML-код
- Опубликовано: 3 янв 2021
- The Nintendo Switch SD Card Reader is easily damaged if not aligned properly. If you have had your console repaired and it no longer reads SD cards check to see if the reader itself is damaged and if not then the connector on the motherboard may be your problem. The reader itself can be replaced as it is plug and play but make sure to exercise caution when installing a new or existing part. They are easy to break.
Need this repair or something else? gocellphonerep...
![[FATAL ERROR]: Switch Doesn't Read SD Cards | Can I FIX It?](http://i.ytimg.com/vi/ON_UOAkQl00/mqdefault.jpg)
![[Paris Olympics] Performance by Australia's Olympic Break-dancer Rachael Gunn breaks the internet](http://i.ytimg.com/vi/i1rl1KhKIjE/mqdefault.jpg)
10:54 doesn't have to be flat....in fact it's gonna sit off kilter like that with the screw in
It just needs to be on and connect
I've been lucky enough and only my read has failed a few times- as long as all the pins are in the connector WILL work
Very good, clear view of micro soldering. Thank you.
Thanks for watching!
Can i replace a pin without solder?
Where did you get the connector? I mean where can I buy it and what’s the name of it? Great video!
Great video. Thanks for this! Great soldering skills too!
Glad it was helpful!
Why couldn't you just heat from under the board? Wouldn't that have helped your struggle @ 6:50 ?
There are components on the other side of the board.
@@GoCellPhoneRepair could you use thermal tape to protect that?
Very nice job. last year i attempted this & my heat gun hand drifted hit my shield and went everywhere bar the connector lol, melted the plastic joycon connectors & flowed the nand :| i was waay too focused on alignment & took too long dicking about( also im a lazy soab & should have taken the nand off ) :( . best bit is, i could have just ordered the connector, pull 2 pins out , popped them in & touched them up. That was last year , too disgusted with myself to touch it so its in the back of my router cupboard , a sombering reminder of what i really am
Thank you.
I kinda destroyed that part and looking to fix it. Just a little nervous about doing this though. I think the easy part is taking it off but my luck hasn’t been good lately
I repared it like 3 times and in a week it breaks again
Can i damage something by changing this pins
I just got all the stuff required to do this on Amazon, for less than 200, even a microscope camera, the same pins were missing from the board, they were still attached to the reader boards connector. They cost 9$ for 2 and the reader cost 9$. Microscope camera 250x zoom 39$, heat resistant tape with no residue 8.99$, 10 feet of copper sodder wick 8$,.a duel soldering iron and hot air station 80$ several tips and accessories, the heat gun all in one. flux 6.99$, also a new volt, ohms, amp meter. 10$ , 🤞hope it all works
So did it work?
Hi there, I got the "1bit" problem and I switch the SDreader part with another one in a Switch who's working well, but the good SD part still does the "1bit" in the bad Switch and the first "supposed" bad reader does the "1bit" too in the good Switch....
So what must I do? changing the reader AND the connector on the first one? Cause when i put back the good SD (who's dont work on the first Switch) on the good Switch it works again without the 1bit thing...
Then you need exactly what he is replacing in the video. Ordered the part a couple days ago and fixing myself soon. Should be possible given the right tools
What type of tape is that? I can't find any good tapes for soldering. that stick well, but that tape looks really good I would like to get some for my own work.
Its heat resistant tape with no residue
Mine looks perfectly fine, as in it doesn’t look like it needs soldering yet, it still can’t read it
Sometimes it is hard to tell for sure without a multi-meter but your problem might also lie elsewhere.
Im considering fixing this. How much would it cost to replace this piece?
Tolle Anleitung. 👍🏼
What's your price on a repair like this
What temperatures should I consider using? Thank you
Is there a digi-key/mouser link for this part?
Where can I send my switch for repair as I have the same issue
Please use the contact form here: gocellphonerepair.com/services/
What type of lead and flux did you use
Kester 63/37 and Kingbo RMA-218.
what's the thermal-insulating tape you use?
Single Side Conductive Copper Foil Tape Strip.
Thanks a lot
Happy to help
i hate this sd card reader!!!!!!!!!!!!! its driving me nuts!!!!!!!!!! i ve been switchless for 1 year now.... I finally got my second replacement... did it myself with utmost care... but now it just decides to not connect properly! like i was installing cfw just fine then all of a sudden it stoped recognizing it! then i put it back, all was fine, and then it worked enough to boot into cfw, but couldnt install games and had low speeds!!! maddening
What temp is your iron at?
If I change the fpc connector, can I still mod my switch?
This is just the sdcard reader connection, it doesnt affect the modability of your Switch
Quick question, how old do I have to be to get a job in this industry?
I would assume whatever the employment age requirement is in your area. If you are young then you might need to look into a work permit of some sort. Labor laws vary by state.
Your material?
Happy New Year 2021 ;)
Happy New Year Johnny!
do you have a mail in service?
I do. You can find details here: gocellphonerepair.com/get-a-quote/
I fucking hate this god damn thing lol