Worked perfect! For those of you wondering about the solenoid. Leave the factory wire harness in and just cut the wires. I lost the remote and cut the wires at the Cdi and ran the wires. Took less than 30 minutes to finish.
with the battery he have on the floor he didn`t have the positive on if you notice he put the negative wire on then to start it he tapped the positive wire on the battery
How’s your push start and killswitch connected? And your solenoid? Just trying to get a rough view of how you got it set up ! Or did you re wire it so you can only kickstart? My bike don’t have the kickstart
i had a starter but i would just stand on the back tire , put it in reverse and use my weight to kick the tire backwards , the starter was never hooked up
@@coojsta69 with the battery he have on the floor he didn`t have the positive on if you notice he put the negative wire on then to start it he tapped the positive wire on the battery
Most Chinese ATVs have a stamped metal placard on the frame up front between the headlights and front wheels. They usually have the serial number, model info, engine size etc.
a green wire that comes form ground connects directly to the spark coil instead of putting the spark plug directly into the engine, this is done to check is you have a spark and when the spark plug is out of the engine. when the spark plug is in the engine the green wire is unnecessary since the spark plug already touching the engine block (which already has ground, this can be seen in the video( one of the green cables connects to the engine block))
with the battery he have on the floor he didn`t have the positive on if you notice he put the negative wire on then to start it he tapped the positive wire on the battery
with the battery he have on the floor he didn`t have the positive on if you notice he put the negative wire on then to start it he tapped the positive wire on the battery
with the battery he have on the floor he didn`t have the positive on if you notice he put the negative wire on then to start it he tapped the positive wire on the battery
You used the starter in this video so how was it hooked up
Worked perfect! For those of you wondering about the solenoid. Leave the factory wire harness in and just cut the wires. I lost the remote and cut the wires at the Cdi and ran the wires. Took less than 30 minutes to finish.
nice this was awesome
How did you turn it over to start?
Don't you guys know? Ur ground for neg side of battery, pos from starter and jumper across the stater relay to kick the motor over
with the battery he have on the floor he didn`t have the positive on if you notice he put the negative wire on then to start it he tapped the positive wire on the battery
I have done all this, now how can I wire my battery back into it to charge?
How’s your push start and killswitch connected? And your solenoid? Just trying to get a rough view of how you got it set up ! Or did you re wire it so you can only kickstart? My bike don’t have the kickstart
i had a starter but i would just stand on the back tire , put it in reverse and use my weight to kick the tire backwards , the starter was never hooked up
@@ghlvvylas3703
So how did you start it on the video?
@@ghlvvylas3703I have an automatic so would you have any suggestions how to start because seems like there is a lot more going on with an automatic
@@coojsta69 with the battery he have on the floor he didn`t have the positive on if you notice he put the negative wire on then to start it he tapped the positive wire on the battery
Couldn't hear you very good. I have the same question everyone else has
Will this work on a Suzuki lt160?
Nice job.how do you tell if I have a 125 cc or 150?
Most Chinese ATVs have a stamped metal placard on the frame up front between the headlights and front wheels. They usually have the serial number, model info, engine size etc.
Forgot to mention - There's always the possibility of things being changed from the original parts though if you didn't buy it brand new.
How can you run headlights
How does the spark plug get power ?
a green wire that comes form ground connects directly to the spark coil instead of putting the spark plug directly into the engine, this is done to check is you have a spark and when the spark plug is out of the engine. when the spark plug is in the engine the green wire is unnecessary since the spark plug already touching the engine block (which already has ground, this can be seen in the video( one of the green cables connects to the engine block))
with the battery he have on the floor he didn`t have the positive on if you notice he put the negative wire on then to start it he tapped the positive wire on the battery
Where do u live cuz my four wheeler still don’t work and I’m ready to sock one of u RUclipsrs
😂😂😂 chill bro me too tho
Do u have a selinoid
I did what you said on the video but it didn't work for me what am I doing wrong
Would love to know the last step of starting? If all bypassed, how did you start it?
with the battery he have on the floor he didn`t have the positive on if you notice he put the negative wire on then to start it he tapped the positive wire on the battery
Where are getting power from?..
with the battery he have on the floor he didn`t have the positive on if you notice he put the negative wire on then to start it he tapped the positive wire on the battery
SO WHERE IS THE RED WIRE TO THE STARTER CONNECTED. I C YOU USED THE NEGATIVE WORE ONLY TO START THE ATV
You connect it to the starter solenoid
it not working
It is fake