Project F11 Comfort Seat Retrofit BMW F10 F11
HTML-код
- Опубликовано: 29 авг 2024
- This is a very simple DIY Retrofit. In this case going from a basic seat option to a fully powered Comfort seat without massage or ventilation only took 3 wires to get them working.
Schematics are in the video. I hope this video helps those that wish to do this swap in the future. Don't forget to Like and Subscribe.
Love this video! Very helpful, I have been stranded with the seats for months! Hopefully this will be the solution to my F10 comfort seat issue🤝
Best of luck! Please do send an update once it's up and running. If any issues come up feel free to reach out, maybe I can help.
Nie wiedziałem że kanał ruszył na nowo. Postaram się dziś nadrobić i obejrzeć wszystkie odcinki z napraw BMW 👍
Well done mate! Have a comfort interior for my g31 and looking to get it installed aswell. Very helpful to see how BMW operates.
Good thing is there is lots of modularity in all of these cars so many things are relatively easy to figure out.
W niecałe dwie godziny obejrzałem wszystkie odcinki dotyczące napraw F10/F11
Did you have any issues with passenger seat occupancy? Your diagram lists it to module A11, what is that? I can see my car is missing the cable, listed 29 on the comfort seats pin out. Thanks!
Not sure but all LHD cars should be set up the same way in a pre face lift. Are you in the EU? Could it be that your seats are from a RHD car? Possibly are your seats from a face lift car and your car is not?
@@DKTNYGARAGE RHD seats in a RHD car for sure. Both pre LCI. I can see the seat loom has an occupancy sensor but the car loom does not have the corresponding wire for it, I can see from your diagram it goes to air bag control module A11 so will try adding that wire and see if the car picks it up. (All coded)
If RHD for a market like the UK your wiring may be different for the left/passenger front. Please check the diagram for your vehicle vin in ista.
Teraz czekam na nagrania z wymiany hamulców.
Can you tell me where I can find the correct canbus wires? I tried at the controller but my wires were totally different than yours. I'm pretty sure the controller must have canbus but I don't know which colours the wires have. It's an 2015 LCI
Get into ista, 2015 is facelift you may have different schematics gotta check for any differences. My car was a pre facelift.
Hey mate, looking to get memory seats fitted to my F10 LCI, it currently has semi auto seats, you have to move it backwards and forwards with a lever, but the back and base can be adjusted with buttons on the sides of the seat. Would I still need to add a power cable for this?
Thanks
Yes but the LCI wiring is different and if you are in the UK the diagram may be even more different. Please download ista and verify with your vin options.
cześć orientujesz się może, czy fotele z F01 2011 roku, podejdą do F11 z 2012 (przedlift)? w swoim samochodzie mam podstawową skórę z pełną elektryką (przód tył, pochylanie, zagłówki, fotel kierowcy z pamięcią, pasażera bez) a fotele z F01 bez wentylacji i masaży. Szyny są takie same, więc mechanicznie powinno być bez problemu, tylko czy z elektryką mogą być jakieś problemy? Z góry dziękuję za odpowiedź i pozdrawiam
Myśle ze mogą być takie same bo to ta sama generacja aut ale dla pewności wpakuj vin z f01 do ista i zobacz czy schematy się pokrywają albo jak możesz to porównaj wiązki, zjęcia wrzuciłem w filmiku.
@@DKTNYGARAGE fotele pasują, wtyczki są te same, fotel pasażera nie zadziałał, ale to pewnie przez to, że nie mam u siebie pamięci tego fotela i nie ma CANa, przeciągnę sobie go z fotela kierowcy, bo pewnie tam jest skoro jest pamięć. Fotela kierowcy nie podpinałem, bo nie wiem czy jak są napinacze pasów, to czy przypadkiem nie zadziałają. A co do oświetlenia ambient, to w siedzeniach, które kupiłem są listwy ledowe z tyłu nad „kopertówkami”, tak jak wspominałeś podciągnę go z oświetlenia regulacji tylnego nawiewu
@@DKTNYGARAGE jeszcze jedno pytanie dotyczące zasilania na pinie 1. Dlaczego nie wziąłeś zasilania z pinu nr 15? Muszę u siebie jednak podciągnąć plusa do fotela kierowcy, bo brakuje na pinie nr 1 i zastanawiam się czy nie można go podkraść z 15. U mnie jeszcze do przełożenia wiązka z napinacza pasa kierowcy bo u mnie w fotelu są dwa, ale nie powinno być problemu z rozplecieniem wiązki ze starego fotela.
Sorry nie widziałem tego komentarza. Teoretycznie 12v trzeba i z tąd by dało rade, ale chciałem pociągnąć kabelki jak fabryka aby potem nie wywalało gľupich błedów czy bezpieczników.
Hey man I was wondering if you could help me out I have all of the other wires only wire that I don't have is the 1 red wire can you tell where did you take connection for that
The red is a power. If you domt have it get a pin from another wiring harness and hook it in then run it to the power source.
Jeżeli możesz to proszę nagrywaj dłuższe odcinki 👍🙂
I would like to put these seats in my e39. Do you know if i would be able to with the wiring? I already have the bracket set up to install in my e39 i just need to get the wiring situated.
Undortunately no idea on F10 seats into am E39. You would be missing a can signal ... maybe a can emulator can be put in place but then again not sure sure if it can work stand alone.
It's Not possible sadly. I already tried these and e60 seats, no chance.
to what pin i need to plug power supply? cause i didnt get it
Take a look at 1:19 the schematic is there for pinouts. You need power to pin 1 on the seat harness and it needs to come from Z1*8B also pin 1.
Hello, i don.t have any pin at pin1 neither in seat cable or in car socket.
I have sport electric seats
You will need to add this pin. Best bet is to get an old cut up wiring harness from like an F series chassis and use that as spares, that way you can pull and cut what you need and splice in new wires. If your car does not have these pins they need to be added.
I haveI connected the 2 wires to the can and now the seats work, but the bottom front/back button works with the controls reversed. Any ideea?
1:43 Obok nowsza wersja BMW serii 5?
Somsiada X3 G01 :)
Why didnt you post the part numbers needed ? I need them :/
Part numbers of the pins were a pita to find. Easiest way is to buy an old e9x or e6x body harness and just de-pin what you need. One harness is good for endless projects.
For anyone who's looking for the pin part number, there you go:
61131383776
Thank you for this :)