I use barrel bio filter and filled the second one with a couple ft of lava rock and bought a bunch of scouring pads (cheap) from the dollar store and filled it up the rest of the way. Works great with very little maintenance.
Great video!! Beautiful pond.🙌😍 I would like to make some observations on your firlter setup. All is just advice to consider.1st. Your UV light will be more efficient if is located in a place where the water flow is the least! If the water flow is to rapid it will not have enough time to kill bad bacterial. In your case its right directly next after the pump flow. So flow in my opinion is to high for UV light to work efficient. 2nd. If your out take is placed (top) at the same height as your intake(top). The flow of the water will swirl on the surface as well as all the filt and go in to the intake continuously at the surface. There for having minimal filter time with your media. I see the media under the intake & the outtake as well. So very little water flow will go through it. Same with your second chamber. Ideally you want intake on top and out take on bottom or the other way around. Your main goal to have a filter to be as more efficient as possible is to have as much water flow going THROUGH the media. I love your Christmas Tree idea.👍
I would also recommend that you install the UV system vertically rather than horizontal. You need to ensure that the UV bulb is fully submerged. Horizontal allows for an air pocket to form.
I agree that more dwell time would enhance either UV functionality. However, since there is on pump and no valves in the system, the water is moving through all the pipes at the same rate - there are no slower sections the way it’s designed. He would need to either add a 2nd, small pump dedicated to the UV, or else tee off a smaller line from the main line, diverting a smaller amount of flow through the UV.
Your setup seems to be working great but I'd personally have the UV on the return to the pond. It would work more effectively after all the gunk has been removed.
Nice filter setup. I was thinking ,why dont you put a 90 degree or a 45 degree elbow on your intake pipe inside your canister to create more of a swirl by pushing the water round the sides and not directly to your outtake.
For the swirl filter you should put lava rock at the bottom for more beneficial bacteria. I love your videos; I will be making a pond of my own this summer similar to your design. I'm going to attempt the combat the bowing that you have with lag bolts not only on the ends of 4x4's but also in the middle.
I thought about putting lava rock in the bottom. This turns the container into a dual bio filter and swirl filter, untill it gets clogged. Since the drain exit is on the top, the debre at the bottom would just settle in the rocks which isnt bad till you need to get it out via the drain. The rocks would just hinder that process. Im after collecting the large chunks and effectently removing them. Thank you for the suggestion though.
I live in Indiana & made 1, I'm wondering if it will freeze in the winter if you have cold winters like we do does it freeze ? if so what have you done to keep it from freezing? I was thinking bubble wrap around it.
Hey bro check out Aquaponic swirl filter, their intake runs all way to bottom of container then tees off with a 45 fitting at the ends. this gives u waay better swirl.Your setup is a bit backwards. The intake is just flowing over to out. Also ADD MORE MECHANICAL!! Lava rock or Pumice Stone works really well and easy on wallet too! I like ya pond. Thumbs up!! Did u build it urslf ? Oh maybe put the UV filter last so that all the gunk has alrdy been filtered/ it'll work a lot better.. Anyway thats a cool pond.
Nice job. Hope it works well for you. Was wondering how often do you change your UV bulb and clean the inside of Tetra UV tube? I have a 2,800 gal pond and 275 gal pond. I have found that my bio-filter hasn't been able to keep up and have had to filter my water through some batting material that I purchase at Walmart in the sewing department. It cleared up my pond in about 7 days but I can't keep that up forever, so thinking of installing another bio-filter on South end of the pond. Nice to see other ideas on how to combat pea green water.
Easy Solution: Place a 90 degree elbow on both your out takes! Place a PVC pipe going down to about 2 inches from your bottom. To increase the swirl efffect, place a "T" connector at the bottom and PVC pipes coming out to the sides with end caps at the end. Drill holes on each PCV pipe that extends to the sides all going towards one single direction. Now place your media again on your barrels and now the water will swirl beautifully from the bottom through all media and to the top to the in takes! A super efficient filtration system for your GORGEOUS pond. 👍🙌
I was just watching a few pond filters in a row, and one guy mentioned that if you run your pond input water close to your pond pump then it does not allow for a full pond swirl. Then he showed how by running your entrance water to the exact opposite side of the pond as far away from the pump as you can get it, that it creates a large swirl and changes out the most amount of water possible. I would say, that if you were to extend your white pvc pipe to the opposite side of your pond as far away from your filter, then you would have an even cleaner pond than you currently do. If you do make this update, make a new video showing the before and after..
I have 8 of those barrels, I am about to use 4 of them to make my filtration, they are 63 gallon pickle barrles, I am using mine to make a pressurized pond filter pumping 3300 gph, any tips on the plumbing?
I've got a couple of pickle barrels that look exactly like these ones. I'm still watching your video but I'm interested to see how your build goes! Looking for ideas for what to do with mine.
Them Bulkhead fitting can be bought at a very good price on Ebay. I would be nice if there was a cheap Wrench to get to tighten them thou -- thats a pain in the rear because they will leak a bit if not very tight.
Thank you a very interesting and informative video. But when will the USA stop using Imperial measurements ? They are so confusing. There are only three countries Liberia Myanmar USA still using them.
and the UK in places and for some things (and, I suspect, for a lot longer) - the OP is in the USA and using local measurements; you cannot expect him to change his nation's units of measurement simply because you are too lazy to convert them to whatever you use. PS please punctuate correctly, it is so confusing for someone using English if you don't
The swirl part is not going to efficient. Put a elbow on it and run to the bottom of the barrel. The pit a tee on the bottom of the pipe and have a some 45 or 90 degree elbows coming off the tee. That will cause a significant swirling motion going from the bottom to the top of your barrel.
Don’t drop your pots so low. The fish love to root and stir all the debris. Also, remove all your dirt from the pots and add rocks only. The will significantly reduce the trash in your water column. I have a channel too if you want to find tips and tricks to koi ponds. Good luck!
@@toolmand2649 Your uni seal leaks? I've probably installed 50+ with never a leak. Make sure you smooth the inside and perimeter of the hole you drill so you don't damage the uni seal. Other than that, I can't imagine a reason for one leaking. You have to use a hole saw. No margin for error on the hole size like with a bulk head. That is the first time I've ever heard of one leaking in all the discussions on fish forms about them. I'm sorry to hear yours leaked. They're so cheap and easy.
It’s like when you girlfriend wants, and you only got a toothpick. Why fish keeper always want a bigger canister, cause bigger canister can hold more bio media. Water pass though the media, the beneficial bacteria will do their job. But with such little media, the bigger the canister is, the more water will pass by, not pass though the media. You can put more media, or just change to a really small container, which the media will just fill it up, that will make sure most of the pumped water will pass through the media, that will work much better, and the water will become crystal clear
4:53 bulkhead fittings are biggest rip-off. ~$19 each at Home Depot. They are less then $2.00 each if you buy black compression bulkhead fittings online…no caulk or sealant…compression!
Shut up, hold still and get on with it! 3,265 flip around pictures of a bulkhead fitting is not all that helpful. But luckily we had closeups of a hole saw!
I use barrel bio filter and filled the second one with a couple ft of lava rock and bought a bunch of scouring pads (cheap) from the dollar store and filled it up the rest of the way. Works great with very little maintenance.
My aquarium also uses 1barrel filter ,1full barrel of lava rock and UV light 36w for 2,400 gallons
Great video!! Beautiful pond.🙌😍 I would like to make some observations on your firlter setup. All is just advice to consider.1st. Your UV light will be more efficient if is located in a place where the water flow is the least! If the water flow is to rapid it will not have enough time to kill bad bacterial. In your case its right directly next after the pump flow. So flow in my opinion is to high for UV light to work efficient.
2nd. If your out take is placed (top) at the same height as your intake(top). The flow of the water will swirl on the surface as well as all the filt and go in to the intake continuously at the surface. There for having minimal filter time with your media. I see the media under the intake & the outtake as well. So very little water flow will go through it. Same with your second chamber. Ideally you want intake on top and out take on bottom or the other way around. Your main goal to have a filter to be as more efficient as possible is to have as much water flow going THROUGH the media.
I love your Christmas Tree idea.👍
I would also recommend that you install the UV system vertically rather than horizontal. You need to ensure that the UV bulb is fully submerged. Horizontal allows for an air pocket to form.
I agree that more dwell time would enhance either UV functionality. However, since there is on pump and no valves in the system, the water is moving through all the pipes at the same rate - there are no slower sections the way it’s designed. He would need to either add a 2nd, small pump dedicated to the UV, or else tee off a smaller line from the main line, diverting a smaller amount of flow through the UV.
Your setup seems to be working great but I'd personally have the UV on the return to the pond. It would work more effectively after all the gunk has been removed.
Yes my words exactly..
Nice filter setup. I was thinking ,why dont you put a 90 degree or a 45 degree elbow on your intake pipe inside your canister to create more of a swirl by pushing the water round the sides and not directly to your outtake.
put a right angle on the swirl filter input, below the surface, swirl in a clockwise motion.
I have 2 right angles on my intake pipe both pointing in different directions makes the swirl effect a lot better
I would add more media and put your uv on the return after the filter on the return. You would have even better results..
For the swirl filter you should put lava rock at the bottom for more beneficial bacteria. I love your videos; I will be making a pond of my own this summer similar to your design. I'm going to attempt the combat the bowing that you have with lag bolts not only on the ends of 4x4's but also in the middle.
I thought about putting lava rock in the bottom. This turns the container into a dual bio filter and swirl filter, untill it gets clogged. Since the drain exit is on the top, the debre at the bottom would just settle in the rocks which isnt bad till you need to get it out via the drain. The rocks would just hinder that process. Im after collecting the large chunks and effectently removing them. Thank you for the suggestion though.
Great explanation. I was really confused on how it all works. Trying to build one for my pond and you really helped me learn. Thank you!
You got the perfect setup for aquaponics there. Turn your dirty pond water into food.
You need alot more bio media. Fill that full of lava rock and have ur return on the bottom of the barrel.
Enjoyed watching! I love making filters myself always fun to share with others! New supporter here!
check the direction of your swirl. I believe northern hemisphere water like to swirl clockwise & vise versa.
Wouldnt the uv work better on the back end after filtration?
I live in Indiana & made 1, I'm wondering if it will freeze in the winter
if you have cold winters like we do does it freeze ? if so what have you
done to keep it from freezing? I was thinking bubble wrap around it.
Hey bro check out Aquaponic swirl filter, their intake runs all way to bottom of container then tees off with a 45 fitting at the ends. this gives u waay better swirl.Your setup is a bit backwards. The intake is just flowing over to out. Also ADD MORE MECHANICAL!! Lava rock or Pumice Stone works really well and easy on wallet too! I like ya pond. Thumbs up!! Did u build it urslf ? Oh maybe put the UV filter last so that all the gunk has alrdy been filtered/ it'll work a lot better.. Anyway thats a cool pond.
Nice job. Hope it works well for you. Was wondering how often do you change your UV bulb and clean the inside of Tetra UV tube? I have a 2,800 gal pond and 275 gal pond. I have found that my bio-filter hasn't been able to keep up and have had to filter my water through some batting material that I purchase at Walmart in the sewing department. It cleared up my pond in about 7 days but I can't keep that up forever, so thinking of installing another bio-filter on South end of the pond. Nice to see other ideas on how to combat pea green water.
Easy Solution: Place a 90 degree elbow on both your out takes! Place a PVC pipe going down to about 2 inches from your bottom. To increase the swirl efffect, place a "T" connector at the bottom and PVC pipes coming out to the sides with end caps at the end. Drill holes on each PCV pipe that extends to the sides all going towards one single direction. Now place your media again on your barrels and now the water will swirl beautifully from the bottom through all media and to the top to the in takes! A super efficient filtration system for your GORGEOUS pond. 👍🙌
ruclips.net/video/Q3lghjW6sfM/видео.html
This is the same concept!👍🤘🐋🐳🐬🐟🐠
What you want to do to make a better swirl you need to put a 45°elbow on the inpipe and lower the in-pipe down in the water than its much better
I think the water inlet at the first tank should be with a tube to the botton of the tank and then a bunch of pebles so big dirt keeps at the botton
I was just watching a few pond filters in a row, and one guy mentioned that if you run your pond input water close to your pond pump then it does not allow for a full pond swirl. Then he showed how by running your entrance water to the exact opposite side of the pond as far away from the pump as you can get it, that it creates a large swirl and changes out the most amount of water possible. I would say, that if you were to extend your white pvc pipe to the opposite side of your pond as far away from your filter, then you would have an even cleaner pond than you currently do. If you do make this update, make a new video showing the before and after..
Great work! 👍🏻
If you want more efficiency out of your small pump you need to eliminate your hard 90s it reduces your flow by 5-10% per 90
I have 8 of those barrels, I am about to use 4 of them to make my filtration, they are 63 gallon pickle barrles, I am using mine to make a pressurized pond filter pumping 3300 gph, any tips on the plumbing?
Great work on DIY filter very interesting new subscriber Barry Manchester England 👍 👍 👍
I've got a couple of pickle barrels that look exactly like these ones. I'm still watching your video but I'm interested to see how your build goes! Looking for ideas for what to do with mine.
Them Bulkhead fitting can be bought at a very good price on Ebay. I would be nice if there was a cheap Wrench to get to tighten them thou -- thats a pain in the rear because they will leak a bit if not very tight.
Thank you a very interesting and informative video. But when will the USA stop using Imperial measurements ? They are so confusing. There are only three countries Liberia Myanmar USA still using them.
and the UK in places and for some things (and, I suspect, for a lot longer) - the OP is in the USA and using local measurements; you cannot expect him to change his nation's units of measurement simply because you are too lazy to convert them to whatever you use. PS please punctuate correctly, it is so confusing for someone using English if you don't
gwmkiwi Never. We will never stop. You can change our mind when we meet on the moon.
Nice video, but why you put the uv lamp before filter ? In my pond uv lamp is placed after filter.
Hi.. how would you hide that so it isn't such an eye sore?
That if all your water run through your uv light it will zap all your good bacteria as well ?
Actually, no - it’s OK. The bacteria live on surfaces, not in the water column, so very little will make it to the UV
You need to route the water down to the bottom to swirl it down there.
The swirl part is not going to efficient. Put a elbow on it and run to the bottom of the barrel. The pit a tee on the bottom of the pipe and have a some 45 or 90 degree elbows coming off the tee. That will cause a significant swirling motion going from the bottom to the top of your barrel.
Also watch out for pollen. Can be a problem in several ways.
Don’t drop your pots so low. The fish love to root and stir all the debris. Also, remove all your dirt from the pots and add rocks only. The will significantly reduce the trash in your water column. I have a channel too if you want to find tips and tricks to koi ponds. Good luck!
I love your plants though
you would be better off using a higher diameter pipe for inlet and outlet, that will give you a faster flow rate
Add an air stone into it and k1 media that will help
Fyi, yes the gasket goes on the water side of the fitting install
For future reference, if nobody mentioned this, Uni-seals never leak and CHEAP. Amazon, ebay, etc.
Maybe i got a bad uni seal....but mine has been nothing but problem....leaks
@@toolmand2649 Your uni seal leaks? I've probably installed 50+ with never a leak. Make sure you smooth the inside and perimeter of the hole you drill so you don't damage the uni seal. Other than that, I can't imagine a reason for one leaking. You have to use a hole saw. No margin for error on the hole size like with a bulk head. That is the first time I've ever heard of one leaking in all the discussions on fish forms about them. I'm sorry to hear yours leaked. They're so cheap and easy.
We just use pvc male and female adapters instead of bulkheads
The fish looked very active, it indicates they getting their 0²
Gravel filter!!!
What plants do you have in the pond?
Your SUV light should be connected AFTERyour bio filter
Seems like way too big and overkill for that small pond.
It’s like when you girlfriend wants, and you only got a toothpick. Why fish keeper always want a bigger canister, cause bigger canister can hold more bio media. Water pass though the media, the beneficial bacteria will do their job. But with such little media, the bigger the canister is, the more water will pass by, not pass though the media. You can put more media, or just change to a really small container, which the media will just fill it up, that will make sure most of the pumped water will pass through the media, that will work much better, and the water will become crystal clear
4:53 bulkhead fittings are biggest rip-off. ~$19 each at Home Depot. They are less then $2.00 each if you buy black compression bulkhead fittings online…no caulk or sealant…compression!
Get your self a 1 gallon paint filter and put it on your skimmer.
man that is one dirty pond. check out my diy pond filter. i feed my koi 20x a day
Use polyester in the swirl filter it will clean up in 48 hours
Good info. But u move to much to fast. But u did a great job.
Got dizzy....
Shut up, hold still and get on with it! 3,265 flip around pictures of a bulkhead fitting is not all that helpful. But luckily we had closeups of a hole saw!
Bacteria, clarifier, barley straw extract, filtration.
"My family over feeding the fish".... this gave me second hand guilt lol.
Get more oxygen in there too dude ✌️👌
5min video turns into 15 min explaining a hole .
You need more flow
Over kill for that little pond mate 😂 great if you got a 30,000 gallon pond tho
Nah, a 30 000 gallon pond needs a wayyyyy bigger filter than this
ろざいが少ない
ポンプが弱いよ。