RAMPS 1.4 - Mechanical Filament Sensor Runout Configuration
HTML-код
- Опубликовано: 16 сен 2024
- This is a simple install video for RAMP 1.4 Mechanical Filament Sensor
One Time Tips, You Can PayPal Me:
www.paypal.me/...
Discord:
/ discord
Patreon:
/ edbraiman
buymeacoffee:
www.buymeacoff...
Required Hardware:
arduino MEGA 2560
RAMPS 1.4
REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
or
REPRAP_DISCOUNT_SMART_CONTROLLER
Mechanical Endstop
Required Software:
Arduino studios 1.8.2 or higher
www.arduino.cc/
Pronterface.exe
www.pronterface...
MarlinFW (Firmware 1.1.6)
marlinfw.org/me...
Thiniverse STL:
www.thingivers...
Thank you very much for this video. I could not get my runout sensor to work to save my life but after watching this, I was able to get it going!! Thanks, again!
thanks a lot, bro! :) works perfectly the same even on marlin 2.0.9
You're welcome.
Salvou meu dia amigo Obrigado
De nada.
Gracias desde argentina estoy armando mi impresora vieja nuevamente ramps y mototores, lo unico que me sale al reves , si tengo colocado filamento me sale que no y viseversa, muy buen video y gracias la traduccion al castellano , desde ya me suscribo a su canal, saludos
Is there a way to prevent X and Y Homing on filament ranout ?
I need it simply to lift 10-20mm and beep, keeping X and Y in the same place.
Does printer not return to same place it left off at?
on the switch which wire goes where? if the switch is laying on the table with the lever arm pointing to your right is red in the center and green on the left or right-hand pin?
Green is signal pin, red is voltage pin and black is ground. The order of the pins can be found on the pinout diagram.
thank youuuuu
Thanks.
Hello my friend ..Then it stop the print ...after from replace filament printing starts from where it stopped...!!!!!!!!!!!! from the moment it stops when you put again fnew filament how much time does it start...you predict to change the material!!!! ust switch off the switch because he wants a little time .....
+Minas ESC Kaisaris there can be several factors in how long it will take. First the length of your tubing and second the temperature at which you print. There maybe other factors so you will need to experiment. Also checkout the configuration advanced tab in marlinfw firmware. Hope this helps.
Edward, please point me in the right direction. when filement runs out the bed moves to far forward and slams the bearing into the end. where can i adjust this forward movement.
When your filament runs out, check configuration_adv.h, it's been almost a year since I did a tutorial and it was with Marlin firmware 1.1.8, I think. You can use Pronterface with debug active to maybe see what commands are being sent.
Edward Braiman found it thanks
You're welcome.
Hi
I tried with marlin 1.1.9 to add the mechanical sensor to pin D11 and I get a lot of errors on ADVANCED_PAUSE_FEATURE
Any suggestions
arduino MEGA 2560
RAMPS 1.4
REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
What are the errors?
@@EdwardBraiman
Arduino:1.8.12 (Windows 10), Scheda:"Arduino Mega or Mega 2560, ATmega2560 (Mega 2560)"
In file included from sketch\MarlinConfig.h:42:0,
from sketch\M100_Free_Mem_Chk.cpp:49:
SanityCheck.h:124:4: error: #error "PAUSE_PARK_[XY]_POS is now set with NOZZLE_PARK_POINT. Please update your configuration."
#error "PAUSE_PARK_[XY]_POS is now set with NOZZLE_PARK_POINT. Please update your configuration."
^~~~~
In file included from sketch\MarlinConfig.h:42:0,
from sketch\G26_Mesh_Validation_Tool.cpp:27:
SanityCheck.h:124:4: error: #error "PAUSE_PARK_[XY]_POS is now set with NOZZLE_PARK_POINT. Please update your configuration."
#error "PAUSE_PARK_[XY]_POS is now set with NOZZLE_PARK_POINT. Please update your configuration."
^~~~~
In file included from sketch\MarlinConfig.h:42:0,
from sketch\I2CPositionEncoder.cpp:31:
SanityCheck.h:124:4: error: #error "PAUSE_PARK_[XY]_POS is now set with NOZZLE_PARK_POINT. Please update your configuration."
#error "PAUSE_PARK_[XY]_POS is now set with NOZZLE_PARK_POINT. Please update your configuration."
^~~~~
In file included from sketch\MarlinConfig.h:42:0,
from sketch\MarlinSerial.cpp:36:
SanityCheck.h:124:4: error: #error "PAUSE_PARK_[XY]_POS is now set with NOZZLE_PARK_POINT. Please update your configuration."
#error "PAUSE_PARK_[XY]_POS is now set with NOZZLE_PARK_POINT. Please update your configuration."
^~~~~
exit status 1
#error "PAUSE_PARK_[XY]_POS is now set with NOZZLE_PARK_POINT. Please update your configuration."
Questo report potrebbe essere più ricco di informazioni abilitando l'opzione
"Mostra un output dettagliato durante la compilazione"
in "File -> Impostazioni"
Sanity check is pointing to configuration_adv.h for setting within. There also might be an issue with an i2c device set in Marlin firmware. Just a guess from the error message. I'd start from scratch in a new Marlin firmware download and compile each change one at a time til the errors appear and that will be the setting to focus on.
can you answer me why did you connect +5V with Vcc in ramp 1.4??
It provides power to 5v rail on RAMPS board for servos. You can verify with a multimeter.
@@EdwardBraiman thank you,i think it had 5v before, i have suggest you should use camtasia to recorder screen, good luck and regards ,i hope your channel will be strong develope in the future .
Why did you not just use the pin 4 and fourth row header pin in the servo bank instead of switching the pins_RAMPS.h and using the third header pin row?
And why does it not work with the RepRap Full Graphic Display? I was just about to set mine up in Marlin, but I don't want to lose the full graphic display..
+Slm Coding it did not work for myself. But if it works for you in marlinfw 1.1.6. then I'm okay with being incorrect. If it doesn't work at least you're confirming the issue I experienced.
+Slm Coding two reasons, one to show how two use or redirect pins and also it doesn't seem to work in my configuration. Granted since I made the video I may have found another option to try. Great question.
If I have time today, I'll check to see if it works. Sorry, I've been CC in English all week.
Edward Braiman just curious, did it work? I've been wanting to add this functionality to my printer since I'll be rebuilding it.
Hello, great video, but unfortunately I have a problem with the implementation and hope that you can help me to eliminate the problem.
I get the following error messages when uploading to the RAMPS board:
In file included from sketch\MarlinConfig.h:42:0,
from sketch\blinkm.cpp:27:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
In file included from sketch\MarlinConfig.h:42:0,
from sketch\emergency_parser.cpp:27:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
In file included from sketch\MarlinConfig.h:42:0,
from sketch\dac_mcp4728.cpp:33:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
In file included from sketch\MarlinConfig.h:42:0,
from sketch\pca9632.cpp:28:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
In file included from sketch\MarlinConfig.h:42:0,
from sketch\malyanlcd.cpp:44:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
In file included from sketch\MarlinConfig.h:42:0,
from sketch\MarlinSerial.cpp:36:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
In file included from sketch\MarlinConfig.h:42:0,
from sketch\SdFatUtil.cpp:29:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
In file included from sketch\MarlinConfig.h:42:0,
from sketch\Marlin.h:35,
from sketch\endstops.cpp:27:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
In file included from sketch\MarlinConfig.h:42:0,
from sketch\hex_print_routines.cpp:23:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
In file included from sketch\MarlinConfig.h:42:0,
from sketch\Max7219_Debug_LEDs.cpp:38:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
In file included from sketch\MarlinConfig.h:42:0,
from sketch\fwretract.cpp:27:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
Mehrere Bibliotheken wurden für "U8glib.h" gefunden
Benutzt: C:\Program Files (x86)\Arduino\libraries\U8glib
Nicht benutzt: C:\Users\Christian\Documents\Arduino\libraries\U8glib_Arduino-master
In file included from sketch\MarlinConfig.h:42:0,
from sketch\Sd2Card.cpp:29:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
In file included from sketch\MarlinConfig.h:42:0,
from sketch
ozzle.cpp:23:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
In file included from sketch\MarlinConfig.h:42:0,
from sketch\G26_Mesh_Validation_Tool.cpp:27:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
In file included from sketch\MarlinConfig.h:42:0,
from sketch\I2CPositionEncoder.cpp:31:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
In file included from sketch\MarlinConfig.h:42:0,
from sketch\SdBaseFile.cpp:30:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
In file included from sketch\MarlinConfig.h:42:0,
from sketch\configuration_store.h:26,
from sketch\configuration_store.cpp:47:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
In file included from sketch\MarlinConfig.h:42:0,
from sketch\enum.h:26,
from sketch\parser.h:32,
from sketch\parser.cpp:27:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
In file included from sketch\MarlinConfig.h:42:0,
from sketch\cardreader.cpp:23:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
exit status 1
In file included from sketch\MarlinConfig.h:42:0,
from sketch\digipot_mcp4018.cpp:23:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
In file included from sketch\MarlinConfig.h:42:0,
from sketch\Marlin.h:35,
from sketch\Marlin_main.cpp:252:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
In file included from sketch\MarlinConfig.h:42:0,
from sketch\least_squares_fit.cpp:35:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
In file included from sketch\MarlinConfig.h:42:0,
from sketch\SdFile.cpp:29:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
In file included from sketch\MarlinConfig.h:42:0,
from sketch\digipot_mcp4451.cpp:23:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
In file included from sketch\MarlinConfig.h:42:0,
from sketch\mesh_bed_leveling.cpp:23:
SanityCheck.h:511:6: error: #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
^
#error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE."
Please help and support!
Best regards Christian
So, tell me about your configuration. What's your 3d motherboard? What's connected to it? What's the version of the firmware? How are you connected I assume a filiment run-out detector?
Hello and many thanks for your quick feedback. After I tried it with the latest version of Marlin, came said error messages. Afterwards I tried it with a slightly older version of Marlin and lo and behold, there were no more error messages and the sketch was already successfully uploaded to the RAMPS 1.4. Now only the conversion from the old mainboard to the RAMPS remains. Hope, there are many more videos of you on this topic RAMPS 1.4 and 3D printers. Keep up the good work and thanks. Best regards Christian
@@christianhofer8398
Hi
I did it all over again, I only uncommented the configuration.h
#define FILAMENT_RUNOUT_SENSOR
It is I already get this error:
In file included from C:\Users\Nino\AppData\Local\Temp\arduino_build_201711\sketch\MarlinConfig.h:42:0,
from C:\Users\Nino\AppData\Local\Temp\arduino_build_201711\sketch\G26_Mesh_Validation_Tool.cpp:27:
SanityCheck.h:502:5: error: static assertion failed: ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.
static_assert(NULL == strstr(FILAMENT_RUNOUT_SCRIPT, "M600"), "ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.");
^~~~~~~~~~~~~
In file included from C:\Users\Nino\AppData\Local\Temp\arduino_build_201711\sketch\MarlinConfig.h:42:0,
from C:\Users\Nino\AppData\Local\Temp\arduino_build_201711\sketch\I2CPositionEncoder.cpp:31:
SanityCheck.h:502:5: error: static assertion failed: ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.
static_assert(NULL == strstr(FILAMENT_RUNOUT_SCRIPT, "M600"), "ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.");
^~~~~~~~~~~~~
In file included from C:\Users\Nino\AppData\Local\Temp\arduino_build_201711\sketch\MarlinConfig.h:42:0,
from C:\Users\Nino\AppData\Local\Temp\arduino_build_201711\sketch\M100_Free_Mem_Chk.cpp:49:
SanityCheck.h:502:5: error: static assertion failed: ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.
static_assert(NULL == strstr(FILAMENT_RUNOUT_SCRIPT, "M600"), "ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.");
^~~~~~~~~~~~~
"C:\\Users\\Nino\\AppData\\Local\\Arduino15\\packages\\arduino\\tools\\avr-gcc\\7.3.0-atmel3.6.1-arduino5/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega2560 -DF_CPU=16000000L -DARDUINO=10812 -DARDUINO_AVR_MEGA2560 -DARDUINO_ARCH_AVR "-IC:\\Users\\Nino\\AppData\\Local\\Arduino15\\packages\\arduino\\hardware\\avr\\1.8.2\\cores\\arduino" "-IC:\\Users\\Nino\\AppData\\Local\\Arduino15\\packages\\arduino\\hardware\\avr\\1.8.2\\variants\\mega" "-IC:\\Users\\Nino\\Documents\\Arduino\\libraries\\U8glib\\src" "C:\\Users\\Nino\\AppData\\Local\\Temp\\arduino_build_201711\\sketch\\MarlinSerial.cpp" -o "C:\\Users\\Nino\\AppData\\Local\\Temp\\arduino_build_201711\\sketch\\MarlinSerial.cpp.o"
In file included from C:\Users\Nino\AppData\Local\Temp\arduino_build_201711\sketch\MarlinConfig.h:42:0,
from C:\Users\Nino\AppData\Local\Temp\arduino_build_201711\sketch\MarlinSerial.cpp:36:
SanityCheck.h:502:5: error: static assertion failed: ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.
static_assert(NULL == strstr(FILAMENT_RUNOUT_SCRIPT, "M600"), "ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.");
^~~~~~~~~~~~~
Uso la libreria U8glib alla versione 1.19.1 nella cartella: C:\Users\Nino\Documents\Arduino\libraries\U8glib
exit status 1
static assertion failed: ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.
Uncomment out advanced pause feature next and recompile. The sanity check shows you the next error to address. You may need to do a couple of times, but you'll understand better with each error fixed.
Hi
I did it all over again, I only uncommented the configuration.h
#define FILAMENT_RUNOUT_SENSOR
It is I already get this error:
In file included from C:\Users\Nino\AppData\Local\Temp\arduino_build_201711\sketch\MarlinConfig.h:42:0,
from C:\Users\Nino\AppData\Local\Temp\arduino_build_201711\sketch\G26_Mesh_Validation_Tool.cpp:27:
SanityCheck.h:502:5: error: static assertion failed: ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.
static_assert(NULL == strstr(FILAMENT_RUNOUT_SCRIPT, "M600"), "ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.");
^~~~~~~~~~~~~
In file included from C:\Users\Nino\AppData\Local\Temp\arduino_build_201711\sketch\MarlinConfig.h:42:0,
from C:\Users\Nino\AppData\Local\Temp\arduino_build_201711\sketch\I2CPositionEncoder.cpp:31:
SanityCheck.h:502:5: error: static assertion failed: ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.
static_assert(NULL == strstr(FILAMENT_RUNOUT_SCRIPT, "M600"), "ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.");
^~~~~~~~~~~~~
In file included from C:\Users\Nino\AppData\Local\Temp\arduino_build_201711\sketch\MarlinConfig.h:42:0,
from C:\Users\Nino\AppData\Local\Temp\arduino_build_201711\sketch\M100_Free_Mem_Chk.cpp:49:
SanityCheck.h:502:5: error: static assertion failed: ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.
static_assert(NULL == strstr(FILAMENT_RUNOUT_SCRIPT, "M600"), "ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.");
^~~~~~~~~~~~~
"C:\\Users\\Nino\\AppData\\Local\\Arduino15\\packages\\arduino\\tools\\avr-gcc\\7.3.0-atmel3.6.1-arduino5/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -Wno-error=narrowing -MMD -flto -mmcu=atmega2560 -DF_CPU=16000000L -DARDUINO=10812 -DARDUINO_AVR_MEGA2560 -DARDUINO_ARCH_AVR "-IC:\\Users\\Nino\\AppData\\Local\\Arduino15\\packages\\arduino\\hardware\\avr\\1.8.2\\cores\\arduino" "-IC:\\Users\\Nino\\AppData\\Local\\Arduino15\\packages\\arduino\\hardware\\avr\\1.8.2\\variants\\mega" "-IC:\\Users\\Nino\\Documents\\Arduino\\libraries\\U8glib\\src" "C:\\Users\\Nino\\AppData\\Local\\Temp\\arduino_build_201711\\sketch\\MarlinSerial.cpp" -o "C:\\Users\\Nino\\AppData\\Local\\Temp\\arduino_build_201711\\sketch\\MarlinSerial.cpp.o"
In file included from C:\Users\Nino\AppData\Local\Temp\arduino_build_201711\sketch\MarlinConfig.h:42:0,
from C:\Users\Nino\AppData\Local\Temp\arduino_build_201711\sketch\MarlinSerial.cpp:36:
SanityCheck.h:502:5: error: static assertion failed: ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.
static_assert(NULL == strstr(FILAMENT_RUNOUT_SCRIPT, "M600"), "ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.");
^~~~~~~~~~~~~
Uso la libreria U8glib alla versione 1.19.1 nella cartella: C:\Users\Nino\Documents\Arduino\libraries\U8glib
exit status 1
static assertion failed: ADVANCED_PAUSE_FEATURE is required to use M600 with FILAMENT_RUNOUT_SENSOR.
The might be a comment in front of advanced pause feature.
@@EdwardBraiman So what should I do, some suggestions
Try it on arduino 1.1.9 to see if it gives you errors too
Correct.
I would, but I'm recording a large tutorial and it might be tommorow before I can try. I'll be record a new tutorial on this soon as this one is a couple of years old.
Gde
Are you asking me, "where"?
Help lcd rep rap full grafik blank not display
What's the LCD type? Are you using the 3d motherboard in the video? What steps have you done so far. We need to know as much about your steps to narrow the issue down. Sounds like the ribbon cables are reversed if the LCD illuminates. It could also be a firmware issue. Can you place a link to the LCD purchase?
s.lazada.co.id/s.IUOn
there is sound when pressed it feels normal only there is no display
firmware problem I have followed some firmware tutorials I have tried
Does the display illuminate? What happens when you reverse ribbon cables position on the RAMPS side position with the notched connection and apply only USB power via you computer USB. Does the LCD illuminate?
Nice video! I would like to make with a CNC Shield and a Ramps 1.4 a Multimaterial Multiplexer for to run 4 extruders can it be possible? thank u!
And Where can i find this STL file i would like to test this runout sensor, thanks again!
+Xergio Velarde yes. I've not attempted, yet.
+Xergio Velarde thingiverse, if it's not in the description, then I'll update on a couple of hours.
Sorry, I'm not sure I understood the initial question, do you mean four runout sensors? It may be possible, but I've never tried and I think the default Marlin may have issues. You may need to modify Marlin FW and currently I'm unsure of the steps involved.
No, I was talking about conect more motors for to have more extruders, like the prusa multimaterial! with the CNC Shield working with the ramps! thank for the answers :)
THANKS FOR THE TRANSLATION ON RUSSIAN
russian:
пожалуйста
English
You're Welcome
Hello Ed, i like your video channel about 3d printer.
I use your instruction for making my 3d printer (ruclips.net/user/shortsmpSAezUBfPU). Can i ask You for help? I would like to make some upgrades of my 3d printer. I bought bigtreetech hot end for 2 filaments in one nozzle. Its posible to mount two filament runout sensors, bltouch and fan controler to servo pins? I would like to save D9 pin for future connection of chamber heater (with external MOSFET), but now i use it for pwm regulation of hotend fan.
Can You recomend me some instructions or tips, which can I use for setting it in Marlin and connecting it to ramps 1.6?
Thank you!
There's a link in either video or channel for Discord, either myself or someone else can help you in general chat.
BAD WAS SEEN IN THE VIDEO