Hey Myke great video thanks for all the work you put in and free content! I've been using glexo on hail but with smaller plastic tabs and I think that smaller tabs would have served you better on those dents. Also the glexo is an amazing pair with blending. Either pop the dent up close and blend it out or get more aggressive with blending and if it ends up a little bit too low pop it up and blend it again. The best part is you're not over pulling or pulling sharp pinches and makes fixing rails a lot better! I have my glexo on a small round hawg tab I believe that also took some time to bond. With smaller tabs it helps to have more glue than normal, mound it up a little bit with your fingers and then use the weight of slide hammer to smoosh into panel
Great video. Thanks for sharing. I've been playing with glue tabs for a week now. I've got a lot to learn. I mean a lot. You know though. It's just a hobby, I'm retired and have my dad's old s10 blazer with a lot of hail damage to practice on. I'm very cautious with tapping down. Today I went and over did it on a couple taps. That's how I learn it seems...
Gracias por el video, tengo un kit basico de cola fria pero no lo he estrenado todavia, viendo los resultados tan buenos voy a utilizarlo en el proximo trabajo.
Hey thanks that's just flat ass awesome Mike great video love it. If you are using this glue and keep it clean like putting it in bag or something that would save the crap out of money. This kit comes complete
I answered that question.. also this was my first take on this glue using this way. It does give a huge head start and doesn’t over pull like normal hot glue does. So if you already have experience with cold glue already, it’s obvious this will be very helpful. Thanks for watching Lukas. 😉
The Light you use allowed me to watch the metal move when you tapped the dent after pulling.
Excellent production. Thanks for sharing you Magic Sir.
Use the wipes on the Tab also before placing the Glue on it
Hey Myke great video thanks for all the work you put in and free content! I've been using glexo on hail but with smaller plastic tabs and I think that smaller tabs would have served you better on those dents. Also the glexo is an amazing pair with blending. Either pop the dent up close and blend it out or get more aggressive with blending and if it ends up a little bit too low pop it up and blend it again. The best part is you're not over pulling or pulling sharp pinches and makes fixing rails a lot better! I have my glexo on a small round hawg tab I believe that also took some time to bond. With smaller tabs it helps to have more glue than normal, mound it up a little bit with your fingers and then use the weight of slide hammer to smoosh into panel
Thanks a lot for the suggestion Garret. I’ll give it a go. I’ll do a follow up on that too. 👊
Great video. Thanks for sharing. I've been playing with glue tabs for a week now. I've got a lot to learn. I mean a lot. You know though. It's just a hobby, I'm retired and have my dad's old s10 blazer with a lot of hail damage to practice on. I'm very cautious with tapping down. Today I went and over did it on a couple taps. That's how I learn it seems...
Gracias por el video, tengo un kit basico de cola fria pero no lo he estrenado todavia, viendo los resultados tan buenos voy a utilizarlo en el proximo trabajo.
! Muchas gracias por sus videos ! ! Es usted el mejor ! Agradecido desde Mexico.
Hey thanks that's just flat ass awesome Mike great video love it. If you are using this glue and keep it clean like putting it in bag or something that would save the crap out of money. This kit comes complete
Like others said, use the wipe-prep on the tab for better adhesion. Probably is the answer for glue coming off tab.
What is wipe prep? degreasing?
I wonder if using the towel cleaner on the metal tip would help with glue not coming of the tip?
How do you store the glue to keep it fresh, debris free once it’s being used? Great demo!
On the plastic clear paper as shown.
forever the best, Myke…..
Can you keep reusing the wipes like the glue? Do you store in zip lock bag or something?
Yell I think your right good job great video
How much can I use per piece of cold glue? Is it semi-permanent?
That's pretty dang impressive! Great demonstration as always too Myke!
Wow great view on video. Did you use a phone for the video? Thank you
Sometimes I do. It’s not the camera that matters.. it’s the content 😉
I would buy the cold glue
what type of slide hammer are you using
1:55
Glexo makes it look all fancy, almost like looking at a set of high-dollar cuff links or something in that category.
It doesn’t matter much if it works. 😉
@@denttime
It will work pretty good while looking pretty I suppose. Everyone will be awe stuck by the craftsmanship and beauty of these gems.
Looks just about perfect!
The Glexo cold glue is the shit i use it everyday makes my job easier!!
whats the most technical best advice you can give on cold pulling?
Hey i didnt see the product in the link you posted
Can you prep puller head also
will it work on my motorhome? I have aluminum panels with hail damage. Please advise
Hey mate,
very well done. Loved the review. Been following you for a while now.
Could you send me a link for the Hammer you use in this video, please?
Like the look of that tap down hammer anybody have a link. Thanks
Great review Myke! Those new tips are beautiful! I was amazed at how well that glue pulled those hail style dents.
Yes thanks I was too! 👊
Will the gelxo pull paint
Anyone knows the basis composiyion of a cold glue, what it is made from?
I'd try scotching the face of the tab surely if it's a little rougher it would adhere better.
Great demonstration indeed 👍 x 100000
try using the prep wipe on the tab, might make it stick a bit better.
👊🙏
Maybe try wiping the tabs with the wipe before applying the glue
But I have no clue haha just an idea.
Hey Mike were Ican get the sledgehammer the green one which weighs
Thank you, for the explanations, and the video.
🙏👍
Anyone else think that reading the directions on the wipes might suggest not wiping the residue off after prep?
Awesome video Mike!!!
🙏 thanks for watching.
How noticeable would the dents be if a person did this in the driveway just to make the dents not appear as bad?
Probably not as good as it would be in shop with proper lighting. A tech can get away with much more flaws in broad daylight than in a garaged light.
Can we use it like normal door dings.
I see vince heat the coldglue by heat gun
I don’t recommend that. That’ll kill the life of the cold glue.
And yes you can use with normal door songs as long as it’s not too deep.
Que buenas herramientas.
will i be able to get this kit with slide hammer on amazon?
If you wait fir 10 seconds before pulling you will give the chance to the glue to settle and bond on dent
Hi😊
👋
What's the name of that first slide hammer you used with the dual weights? I wouldn't mind having one in my mobile arsenal!
BandD slide hammer. BandDtools.com
Prep the tab also
مرحبا انا من الجزائر وأريد اعرف كيف تصنع cold glue
file grid on the tab
cold glue for big soft dent ok, for the others hot glue is more accurate and fast that i thougt.
Great video 🙌🙌 Just wanted you correct you on Tom Brady comment he has 6 💍💍💍💍💍💍 😂😂
😂 I knew you might Scatto! 👊🤣
Cheated for 3 so he got it right! 3rings!
Woww👍
you can get cold glue kits from china now for $28.
Put your board little bit further , you can not see no details, yes its pulling oke, but the quastion is if it pulling also the center of the dent...
I answered that question.. also this was my first take on this glue using this way. It does give a huge head start and doesn’t over pull like normal hot glue does. So if you already have experience with cold glue already, it’s obvious this will be very helpful. Thanks for watching Lukas. 😉
$300 for the hail kit and $70 for the additional glue? Ouch. Must be an American company with prices like that.
So you think it’s super important to keep cleaning the surface of the car to get a good bond yet you don’t clean the surface of the tool.
Not needed. 😉
Fast forward to 17 minutes. You're welcome.
As I mentioned before. Only the DIYers are impatient and don’t care for the details. Thanks for watching.
😍😍😍😍😍
3:13 😂😂😂
Nice ring 😅🤣
very long ad
Too much talking little action. You should have been a radio host.
You want action and no talk.. go to TiKTok.
Holy s*** is that jewelry or PDR 😂