Well done guys! You make it look very easy! How much oil can your oil pan take? It must be more than 5 lt otherwise you had an overflow of nice black oil on your clean floor! 😬🤭
Any ideas how to undo a badly burred hex on cap. Do think i could drill the hex and use an eg. 1/4 inch rachet extension through the hex like a t-piece or is it molded hollow which would put drill shavings in the filter pot. I would think it to be a solid hex because hollow would collapse or twist under socket tension. 🏴☠🌤. Hello from down unda.
Hello brother...check for oil leaks...crankshaft oil seal,sump and front engine cover...notorious for leaks...just had my 2015 XLT in for repair...very expensive job
I know right , I was on the edge of me seat watchng them fluff around , sump bolt OUT ,, mind he did nip under and pop bolt in before replacing the Filter ,,, quite possibly the clumbsiest oil change I've ever seen 🤣🤣🤣 good for a larf Watching this gives me peace of mind I'm gona be just fine 😅😄
Hi Guys.Thanks for the video. I have a BT50 2018. Did anyone noticed an oil filter by-pass valve in the oil filter housing. i have a weird sound coming in from the cap at cold start and will last for 15 minutes until engine gets hotter. Any clues will be appreciate. Thanks
Well done lads. I just did mine after watching this! I had googled this before, Google mentioned doing this within 10min. What do you think of the 10min rule?
Not every time but if you leave a Ranger engine without oil for longer than ten minutes you DO run the risk of the oil pick up running dry, it will never correctly refill again and the engine will have catastrophic failure, it is the one car we have strict rules on having everything ready prior to draining the oil!!!
animal79thecat is 7L definitely right, I changed mine but I’m sure it’s over filled but it’s hard to tell on the dipstick they’re useless on the ranger.
what a stupid ford ranger oil filter, its so messy and dirty type to replace.. why not ford use oil filter cartridge like other car manufacturer 7 liter w/o oil fiter change... 7.5 liter if you also replace new oil filter for model 2.2 liter maybe 3.2 liter use more quantity of engine oil
Hi boys. Well done. We also went behind the panel.
Easier with the wheel off. Cheers.
Well done guys! You make it look very easy! How much oil can your oil pan take? It must be more than 5 lt otherwise you had an overflow of nice black oil on your clean floor!
😬🤭
Good work
Thanks
Any ideas how to undo a badly burred hex on cap. Do think i could drill the hex and use an eg. 1/4 inch rachet extension through the hex like a t-piece or is it molded hollow which would put drill shavings in the filter pot. I would think it to be a solid hex because hollow would collapse or twist under socket tension. 🏴☠🌤. Hello from down unda.
Hahahaha funny locating the oil filter, i also struggled.
Thanks guys, take the front left wheel off, makes life easier!
Good tip !
Thank you
Hello brother...check for oil leaks...crankshaft oil seal,sump and front engine cover...notorious for leaks...just had my 2015 XLT in for repair...very expensive job
Good advice ! We will give it a good clean and check for leaks !
What about the 10 minute rule, I read that truck might not be delivering oil as it should now
I know right , I was on the edge of me seat watchng them fluff around , sump bolt OUT ,, mind he did nip under and pop bolt in before replacing the Filter ,,, quite possibly the clumbsiest oil change I've ever seen 🤣🤣🤣 good for a larf
Watching this gives me peace of mind I'm gona be just fine 😅😄
Thanks for locating the filter for me lol
Hi Guys.Thanks for the video. I have a BT50 2018. Did anyone noticed an oil filter by-pass valve in the oil filter housing. i have a weird sound coming in from the cap at cold start and will last for 15 minutes until engine gets hotter. Any clues will be appreciate. Thanks
How long did you leave between emptying the oil and refilling the oil?
Me too, what will it be?
Well done lads. I just did mine after watching this! I had googled this before, Google mentioned doing this within 10min. What do you think of the 10min rule?
I think do the filter first,then dump the oil,fill then start within about 15 minutes. No need to do a long drain to get every bit of old oil out.
Not every time but if you leave a Ranger engine without oil for longer than ten minutes you DO run the risk of the oil pick up running dry, it will never correctly refill again and the engine will have catastrophic failure, it is the one car we have strict rules on having everything ready prior to draining the oil!!!
so how much did you put in after rechecking the oil level? is it 7.5 litres still? because i'm not gonna drown my engine if 7.5 litres is enough.
Ive got this pick-up and 7 litres is enough...trust me! (2.2)
animal79thecat is 7L definitely right, I changed mine but I’m sure it’s over filled but it’s hard to tell on the dipstick they’re useless on the ranger.
7 liter w/o oil fiter change... 7.5 liter if you also replace new oil filter for model 2.2 liter maybe 3.2 liter use more quantity of engine oil
What is the specification and brand of engine oil and oil filter too?
Thank you!
5w30 Synthetic & it takes about 8.6 litres
a trick: you can watch movies on flixzone. Me and my gf have been using them for watching all kinds of movies during the lockdown.
@Edward Brody Yea, I've been using flixzone} for years myself :D
Topíssimo
14.43 Overflow hahaha 9.75 Lites 😂😂😂😂😂😂
Dude
what a stupid ford ranger oil filter, its so messy and dirty type to replace.. why not ford use oil filter cartridge like other car manufacturer
7 liter w/o oil fiter change... 7.5 liter if you also replace new oil filter for model 2.2 liter maybe 3.2 liter use more quantity of engine oil
13.17 Fuckkkkkkkk
If you two are mechanics god help us, because you are clueless 🤷🙆🤦😂😂
Amen to that sir ! Not a mechanic...god forbid ! just a chartered Engineer and Fellow of the institute of motor industry ( FIMI )