Eibach sportlines with kyb struts Miro 111 18x9.5 18x10.5 +40 with 5 mm spacer up front to clear the brembos Kooks headers 1 7/8 into 3 inch Kooks y pipe No scraping issues with the exhaust, it will touch occasionally on the driveshaft loop if the road is uneven
@@bhcamaro2002 how low is the drop on the sport lines? I'm thinking of getting the Sam strano springs with Koni str.t but I'm not sure I'll like the way it looks. My LT's hang kinda low. (eBay). I may just save up and go the kooks route. Btw I really appreciate the response. I think your wheel/tire set up is perfect. Btw what is your tire size.
It's pretty low, I'd say it was overall a 3 inch drop from the factory springs. Also I have a heater hose mod on the rear dropped it another half inch to even out the stance. The eibachs are not the best for ride quality. I'd recommend a umi spring for performance or coilovers if you can afford them, then you'll be able to dial in the ride height. It has Nitto nt05 275/35 front 295/35/18 rear.
Magg performance splitter, they were aftermarket led taillights with paint cleared over. They were 12 years old and started to get sunfaded I decided to go back to my oem taillights.
Beautiful car . I have a 35th z28 . Question. What kind of lights are those because I have gaps in mine . And is the suspension lowered ? It looks lower than stock .
Thanks man! Nice! They're depo headlights I put a small urethane spacer behind the headlight bracket helps eliminate that huge bumper gap. It's lowered on eibach sportlines with kyb struts and the heater hose mod in the rear
Thanks man! It's on eibach sportlines and kyb struts with a heater hose mod to the rear. Not the greatest ride quality with the eibachs but it does sit nice
@@bhcamaro2002 air intake valve can get plugged up with exhaust/oil over a long period of time and fail to work correctly. Until I began googling the issue I didn't know there was an electric activated valve in the side of the throttle intake. Yes there are a couple electrical connections there but.
Have you ever had your Camaro stall when hot idling in a lineup? Mine does and I replaced the fuel filter and air intake valve. Idles down to 550 rpm. Driving fine on highway so I doubt it’s fuel pump?
I resolved the problem. After replacing the air intake valve I decided to disconnect the battery and reconnect it the next day. Seems to have reset it, now it idles once warmed up at 550 rpm without any problems
I would get a set of prc 2.5 heads a cam like a btr stage 3 and supporting mods like longtubes, ls6 intake if you have an earlier ls1, slp lid , should be in the low to mid 400s
The polished face and silver wheels are perfect. Excellent combo. Thank god you didnt do black wheels. Looks like garbage and way over played (black.on black)👍👍
shes..... so beautiful
Thanks!
Car looks great.
Thanks man!
Great job on the detailing!
Thanks!
Beautiful! 🔥
Thanks! 👍
Outstanding! I wish it was mine!
Thanks! Alot of time into it!
I need more details on your suspension and wheel set up. Also do you have LTs if so are you scraping them all the time?
Eibach sportlines with kyb struts Miro 111 18x9.5 18x10.5 +40 with 5 mm spacer up front to clear the brembos
Kooks headers 1 7/8 into 3 inch Kooks y pipe
No scraping issues with the exhaust, it will touch occasionally on the driveshaft loop if the road is uneven
@@bhcamaro2002 how low is the drop on the sport lines? I'm thinking of getting the Sam strano springs with Koni str.t but I'm not sure I'll like the way it looks. My LT's hang kinda low. (eBay). I may just save up and go the kooks route.
Btw I really appreciate the response. I think your wheel/tire set up is perfect. Btw what is your tire size.
It's pretty low, I'd say it was overall a 3 inch drop from the factory springs. Also I have a heater hose mod on the rear dropped it another half inch to even out the stance. The eibachs are not the best for ride quality. I'd recommend a umi spring for performance or coilovers if you can afford them, then you'll be able to dial in the ride height. It has Nitto nt05 275/35 front 295/35/18 rear.
Looks beautiful man. The only thing you still gotta do is darken those tints. That’s essential for the Darth Vader look.
Thanks! Yeah I wanna go darker on it haha
@@bhcamaro2002 I promise you’ll thank me later. Love that car btw 🇺🇸💪
No doubt! 🤟
Great looking ride. Whats your wheel dimensions size and offset. I was thinking gunmetal f-14s for mine. With some coil overs.
Thanks! They're 18x9.5 18x10.5 5x120 +40, had to add a 5mm spacer to clear the brembo calipers
DAM! That. 😎 SHINE 😎
😎💪
Is that tuxedo black?? It looks great…I see you have some Nitto Nt05s, i have the same tires on my New Edge..
Yes it is! Great tires, they hook really well when they're warmed up
Looks Nice!!! What paint do you use?
Thanks! It's Ford tuxedo black paint
What turn signal lights are those?
Factory lenses tinted with clear
What pedals are those? They look good. Freshens up the interior.
Thanks! They're srp pedals
@@bhcamaro2002 Thanks. Might have to pick myself up a set for my Z28.
Cool car man .. where do get the front bumper splitter ?
Thanks! Magg performance sells them
@@bhcamaro2002 much thanks man ... do thay ship overseas ? And what did it cost?
I'm not sure about shipping, they had a sale at the time I got mine for $325
@@bhcamaro2002 really Appreciate the feedback man you're the best 😘
What tail lights do you have? And what tint did you put?
They're just ebay led lights that I had a painter tint with a few coats of clear coat
🔥🔥🔥🔥
😎👍
What front lip is that. Also is that film tint or aftermarket tailights
Magg performance splitter, they were aftermarket led taillights with paint cleared over. They were 12 years old and started to get sunfaded I decided to go back to my oem taillights.
@bhcamaro2002 nice thanks bro
Anytime
Beautiful car . I have a 35th z28 . Question. What kind of lights are those because I have gaps in mine . And is the suspension lowered ? It looks lower than stock .
Thanks man! Nice! They're depo headlights I put a small urethane spacer behind the headlight bracket helps eliminate that huge bumper gap. It's lowered on eibach sportlines with kyb struts and the heater hose mod in the rear
@@bhcamaro2002 thanks man. It's time for new headlights so I think I will try that .
No problem!
What did you use to lower the rear? I’ve got SR12s which are the same mold as the miros and looking to switch to that tire size. Love the fitment.
Thanks man! It's on eibach sportlines and kyb struts with a heater hose mod to the rear. Not the greatest ride quality with the eibachs but it does sit nice
Do you have the part number on your steering wheel? I'd love to change mine out. This stock one. SUCKS. To big.
I don't did the wheel so long ago for the same reason. Look up momo competition on ebay, you'll have to buy a hub adapter as well and modify it to fit
@@bhcamaro2002 ok. What's the diameter of yours?
Have you ever had your Camaro stall when hot idling in a lineup? Mine does and I replaced the fuel filter and air intake valve. Idles down to 550 rpm
Never had a issue with idling, I'd look into a tune for something like that
@@bhcamaro2002 actually after replacing the air idle valve I later disconnected the battery. It seemed to reset it and worked fine afterwards.
That's another thing I never thought of checking, nice!
@@bhcamaro2002 air intake valve can get plugged up with exhaust/oil over a long period of time and fail to work correctly. Until I began googling the issue I didn't know there was an electric activated valve in the side of the throttle intake. Yes there are a couple electrical connections there but.
I would recommend a catch can to prevent oil build up in the intake
Have you ever had your Camaro stall when hot idling in a lineup? Mine does and I replaced the fuel filter and air intake valve. Idles down to 550 rpm. Driving fine on highway so I doubt it’s fuel pump?
Never had that issue before
I resolved the problem. After replacing the air intake valve I decided to disconnect the battery and reconnect it the next day. Seems to have reset it, now it idles once warmed up at 550 rpm without any problems
Probably the pcm reset it
what wheels are those?
Miro 111 18x9.5 18x10.5
How much would it cost in mods to make similar horsepower as your car?
Depends what you go with, if I had to estimate I'd say around 6k if you do it all yourself
I would get a set of prc 2.5 heads a cam like a btr stage 3 and supporting mods like longtubes, ls6 intake if you have an earlier ls1, slp lid , should be in the low to mid 400s
Very similar setup to what I have, making 426 at the wheels
The polished face and silver wheels are perfect. Excellent combo. Thank god you didnt do black wheels. Looks like garbage and way over played (black.on black)👍👍
Thanks! I agree black wheels would be too much
Surprised to see your sail has no bubbling
It was replaced a few years ago, the glue had started to bleed through. 2000-2002 had the cheap glue issue unfortunately
@@bhcamaro2002 yeah, I'm afraid I'm going to have to take mine off and redo it. Very nice camaro though bro. Keep it up👍
@@wesley3083 thanks! Yeah that's the only way to go. Repainted it once years ago and the glue came back so replace it and never worry about it again 👍
Can i drive it
Black. What a beautiful color. Black. What a horrible color, when it comes to cleaning.
No doubt! Alot of frustration getting it to this condition, but definitely was worth the effort