Apprecaite the videos brother. My passenger side blew hot air and i knew it was the blend door so i just closed those vents. I accidently turned the heat on the other day and now nlboth sides are hot. Are both motors accessible like what you showed in this video? Than you.
From what i have gathered, i have the B1443 code on my 2015 Lexus IS, from what i got from Techstream , i've read your older comments. its the driver side, biggest one on top - removal of the driver knee bag - removal of some trim pieces around the dash console - disconnect battery for 15 minutes before starting anything else i should know before starting/ do you have any videos of it? thanks!
Thanks for watching. I don't think the 2008 model IS350 or IS250 have this campaign. It's on the 2013 and up. But if the servo motor does go out this is a similar process for replacement!
Hi harbor im having b1455 saying driver side but when i check on the hvac manual it shows me number 10 on the passenger side just on top of the one you did on this video can u explain me? Thanks man your the man.
@ last question your telling me is on passenger side but when i check error code says Air Outlet Damper FOOT / DEF Control Servo Motor Circuit ( Driver Side )
The service manual says that servo motor initialization is a necessary procedure when disconnecting/recomnecting the battery. Whether it makes a huge impact, i personnaly dont think so, but it does state that it may effect/inoperative funtction when necessary procedures are not performed.
Great video, my 2018 is f sport have this problem few days ago. I brought the diagnose tool, gonna to re calibrate it. If it doesnt work, will replace it. But my car is right hand drive, hope that servo motor can be easily access.
@@harborareatech310 Actually my driver side blow hot air, not the pax side. The far right vent is much hotter than the middle right one. Can you give me hint that where's the servo motor for controlling the temp. of the driver side? Is it inside the middle console beside the knee? Or wherever which side blow out the hot air, it's the same servo motor?
@@erickespinoza6998I’m having this same problem with my is350 right now I scanned it and it says driver foot servo motor circuit did u ever figure out how?
Can you please make a video on how to change the air outlet damper cool contorl servo motor? My ac is blowing hot air. It’s from the passenger side it’s so high up I can’t reach it
Just dropped off my 2017 IS 350 for the exact same issue. I got a letter from Lexus indicating my warranty for the AC was extended 7 more years or 125k miles
@@harborareatech310 The Lexus El Cajon dealership had 2 LFAs in their show room. One being a Nurburgring Ring edition ONLY one in red over 2 million dollar car (the only red 3P0 LFA) 🔥 the other one being a red LFA. So BEAUTIFUL….!!!
Great video! I just noticed my RC350 was doing this about two months ago. Seems like a project I can handle. Question: I have that nasty smell when I first turn on my A/C. I can't do the evaporator cleaning where you spray cleaning foam using the drain line due to it being on top of the transmission. Would I be able to do that cleaning when I replace the servo? Is there a spot I can insert the spray or would I have to drill a small hole then plug it after? Thanks!!
Thanks! Always check with the dealer first to see if you're covered. If not, refer to the trouble code to see which servo motor is at fault. On your vehicle, it shouldn't be that hard to replace them. To answer your question, I dont remember off the top of my head, but you may have an access view of the evaporator through the inside of the vehicle toward the firewall center area on the passenger or driver side. If so, you can spray the evaporator through there. if not, you can always spray the outside cowl area with the a/c on max with the fresh air mode on and all windows closed. Then, always replace your ac filter with the charcoal style one, and when turning off your vehicle, ALWAYS leave your ac on fresh air mode to prevent excessive moisture buildup. That is what causes that mildew odor.
@@harborareatech310 Thanks for the quick response!! I'll check and see if the evaporator is visible or not, I want to say I've tried this before and could not see it. I saw at the 12:30 mark, a small white plug-looking thing. If I can't access the evaporator, I'll check to see if that is a plug and reply back. Thanks again and hope you are able to enjoy your weekend and not have to work like me, lol
So I was able to access the evaporator by removing the glove box, etc. I removed an adapter that was used for the floorboard a/c and from there I could see right into the evaporator. The only thing is you have to have the a/c settings set to Floor before turning off the vehicle so the floor port opens up. After that, I was able to spray the foam cleaner in there. What a difference. So glad I found your video! Thanks again!!
@leojohnwayne1422 after I took apart my glove box and everything above, I used Nextzett Klima Cleaner. One can was more than enough. After I did this, my a/c had zero smell.
Thank you so much for this video! I have a 2015 Lexus IS350 f sport and have the same problem . I will order a new A/C Servo Motor and do it... btw What scan tool you are recommend to buy? again thank you so much for the GREAT video.
Thanks for watching. I used the vehicle manufacturer scan tool (techstream) in this video. If you do not own a scan tool, i would suggest borrowing one or looking online "how to download techstream on a laptop " and just buying the data link connector to connect to your vehicle.
@michaeldao1711 I have the same year and model.. can you pls let me know the part number that you ordered (A/C Servo Motor) for Driver and Passenger side ? thank you in advance
@jonatbass1111 these parts are for IS models 2014and newer b1446 part numer 87106-30570 location is driver side lowest servo motor on the hvac box. B1453 part number is 87106-30610 location is on the driver side middle servo motor on the hvac box. And b1454 is the same part number as b1453 but is located on passenger side ( the one i replace in the video). For location you can refer to 7:29 of the video.
You said the servo motor needs to be lined up with the flat spot on the AC box, yeah? Do we line it up by turning the flat spot on the AC box or turn the "gear" on the servo motor? Or it doesn't matter? Thanks.
I’ve had the hot air issue resolved by the dealership but now mine gets stuck on defrost mode. The dealer states they fixed but continues to happen. Can you explain what servo motor or blend door actuator controls this function ?
I brought my 2015 IS350 in for this exact issue... Just was called that it is $2400.. The only difference is it is the drivers side... Looks like number 6 from your document.... Question is.. Can this be done without that diagnostic tool that you have? Looks like it needs to be reset/programmed after the new one is installed.....
You can replace the servo motor yourself, always refer to the stored trouble code in your vehicle to know which is the servo motor affected. You may have better results after just replacing the affected servo motor, but in order to have the optimum A/C performance, the initialization is required.
@@harborareatech310 Thanks.. I just ordered a cable from Amazon and when it gets here I will download the software and try to use it that way... I am also trying to get my service advisor to call me back.. Have read a few things about how long it should be covered.. I have had this at Lexus 3 times already for this over the years and all they have done in the past was to "reprogram" the computer.. Seems to happen every year when the AC is actually shut off for a few days.. South Florida we use AC a lot :)
@joelee5493 thats a good idea! in order for it to actually qualify for the extended service campaign repair, the servo motor troble code needs to be stored and active after the reprogram. sometimes, the reprogram takes care of it. Maybe that was your case in the past. From what i noticed, hot areas are affected the most by this issue.
@@harborareatech310 After the cable gets here that is the plan. Since this has happened before... question is, what bad would it be if replaced them all since the dash will be taken apart already??
@@harborareatech310 I will try it just in case.. If it doesn't work I still take the dash apart. Not looking forward to that but it is def better than paying $2400
Hello, great video. I was wondering if the process is similar on a 2013 GS350 AWD. I have a code B1443 and dealer says $2400 to replace bad servo motor. I missed the recall period because I wasn’t aware of the bulletin. Is that motor also accessible without pulling the dash? I would love if you could do a video on the GS350. A few other members in our GS facebook group is also interested in this. Thanks.
Hey, thanks for watching and the comment. I will try to answer as best as i can. It has been a while since i ve replaced that one. But i believe you can do all servos on the GS 350 without removing the dash. That is the largest one on the driver's side, and i believe it is the same concept as the one in the video, if not very similar. If the opportunity arises, i will make a video. If you are local to the los angeles CA area, i can make a video for the GS community.
Wow, I’m so impressed on your quick response. I wish I was in LA, but unfortunately I’m in Boston MA. Any additional information on how to replace would be greatly appreciated. If you know the part number for the servo motor would also help. I’ll also check in the user group if anyone having this issue is in the LA area. Thanks
Greeting good sir, where do you find this repair manual? I’m looking to purchase one for Lexus NX and RX series! Any tip would be greatly appreciated. You’re awesome
I have manuals because I worked at the dealership. If you want repair manuals you would probably sign up for some sort of autor repair database like All Data or Mitchell.
Nice video, I have a 2016 gs350 driver and passenger take turns being hot, cold or won't blow at all. I did replace my battery about 6 months ago but i didn't notice a problem right away. I noticed it after being out of town for a couple weeks without using the car. You said the servo motors are supposed to be re-initalized, does that have to be done at the dealer or can i do that another way like with a Blue Driver obd tool?
I would check first to see if it is covered by the dealer. There is a secondary coverage customer support program that a lot of lexus vehicles fall under this program. i believe it's 7 years from the date of first use or 125k miles, whichever occurs first. To answer your question, though, a more advanced scan tool is required to initialize the servor motors. You can always download the lexus/toyota software "techstream" on to your laptop by looking it up. You would just need to buy the obd cable to connect from the laptop to the vehicle.
@@harborareatech310 Thank you, really, thanks it's appreciated. Obviously you're a good tech with a knowledgeable and accurate answer. I guess even if I bought a servo motor, there are multiple and I wouldn't know for sure which to buy? And lastly, even if I get the right one and I replaced it, then it won't work right because it needs to be initialized?
@mattdi333 you need a scan tool capable of retrieving trouble codes from the body control module to determine which servo motor is at fault. After replacing the servo motor, if you dont intialize, you won't experience optimum perforformance
I have a rc 2019 my servo #1 87106-30510 is going bad Lexus quoted me 3k+ to replace it. I’ve bought the servo that’s going bad and I want to replace myself but if I disconnect the battery is anything else going to deprogram? Also if I replace the servos myself is it mandatory that they need reprogramming?
@josephribs if you disconnect the battery and/or replace a servo motor(s), they would need to be initialized for optimum performance. If not, they most likely would work but not at its best performance. Ch3ck out my video ruclips.net/video/Ad2X1XXt3Sc/видео.htmlsi=-8IJsXdISHzg2Yxp This is an affordable scan tool I recommend al toyota and lexus owners to have. It is capable of performing the servo motor initialization and many more functions.
Hello I just took my RCF to the dealer for this same issue, looks like it’s not covered under warranty anymore. I have trouble codes B1441, B1443, & B1453. They said the dash needs to be removed as well is there anything you recommend to avoid that or which servos to replace
@Loudbasshead_ I don't remember the RC-F off the top of my head, but I believe it's similar to RC. If so, it can be done without removing the whole dash . Accordimg to the codes you gave me, you have 2 servo motors on the driver side, and one on the passenger that are at fault. I would recommend changing only the servos triggering active trouble codes
@@harborareatech310thanks for the reply! Would you happen to know which ones exactly to buy and replace Lexus is charging over 2800 and sadly out of warranty with the CSP
Are the 3 motors shown in the video during the repair accesible to replace without removing the entire box? And for the driver side as well? Thanks in advance!
First, check with your local dealership to see if your vehicle either falls under the technical service bulletin or service campaign. If it does, then the repair will be covered through them. If not covered, then you will need to obtain the trouble codes recorded in your vehicle in order to see which servi motors are affected
Ive taken my RC in for the recall, both centers were blowing hot while AC was at 68. They fixed it but now I'm back to all driver side vents blowing hot and all passenger vents blowing cold. Is this still covered under the recall, or do I need to pay to replace the servos? And which servo is it for the driver side? just want to prepare my bank account if payment is due lol
Hi, just wanna pick your brain, if the error code is B1453 as shown on techstream, on a RIGHT-HAND drive car (Japan), is it still the same servo motor on the left side of the vehicle? Does the error code mean different part for RHD vs LHD or is it the same, regardless?
@@harborareatech310 Yes, turns out you are right, mate. In your video, you done it on the passenger side, in your opinion is it easier or harder to get to on the driver's side? Also, can I just simply unplug it after re-initialization so that it doesn't ever blow hot air?
Hmm... read through the bulletin and it seems that there is a need to flash a new calibration to the ac amplifier and that would solve the servo motor issue? Instead of replacing them.
Hello ,any chance you can help me by pointing out where to find B1443 servo on RHD/UK model,is it passenger or driver side?I sourced the code and it's 43 displayed on the climate control , symptoms no air going through console vents and no memory stored for AC.Thank you in advance.
@@harborareatech310 2014 lexus is300h,as mentioned in my previous comment it is UK model. From what I could find it looks like AC unit has to come out to access this particular servo , according to the lexus bulletin.Thank you for your reply, appreciate it .
@@harborareatech310 just a quick question , according to service report from August 2018 the fault was already there,no air blowing out of the vents ,it only blows on the windscreen,feet won't get air too.I am the third owner ,first owner had this issue diagnosed while the car was 4 years old and 62 k miles on the clock by Lexus .Do you think I can have a foot to stand on and try to chase them to fix the issue? He paid for extended warranty and there are loads of service reports but none about this issue being fixed .
@michalnowak3558 I'm not sure about that vehicle. We dont have that model over here. But if it's anything like the IS350, it will be on the driver side top servo motor, which is the biggest servo motor. It can be done without removing the whole dash, only the driver side knee air bag, and a couple of covers need to be removed. You can try to contest the issue at the dealer, and if you are persistent enough, they might goodwill the service, but it is not guaranteed.
will this also fix this mode issue?? I have issue with mine mode not changing mode correctly and blowing air everywhere except where I wanted. If so do I need to replace all 3?
@@Arcanny certain servo motors do affect the mode operation. The vehicle will need to be scanned and properly diagnosed to see which servo motor(s) are at fault
Hello. Do you happened to know where is the mode servo piece located at. Im having issues with my 15 lexus rc350 with the mode switch not properly working right
@@harborareatech310 I have a question. If anyone had this issues please comments. So far this is all my trouble code due to my Air conditioning. My problem was the air coming out from all vents blowing to my face with LO(60 degree temperature - until I changed to heat temps. Both of my Driver/passenger vents changed to blowing to bottom. It went bad when I changes my temperatures to cool and my air vents wont blowing like it before i changed to heat. Sorry for the incorrect sentences. Please any advices would help.
No, if you replace the servo, you just need to make sure you are equipped with a scan tool capable of performing an ac system initialization. For optimum ac performance
So there is a much easier way. Loosen the 2 little silver screws all the way, that are on the outside of servo that you can see. This releases the servo from the mounting bracket. Then remove mounting bracket from new servo and install back on Car on old mounting bracket. Once you break the screws free which is very easy, you can remove and reinstall with your finger tips then snug up with Phillips. Sooooo much easier! Note slide the long mounting bracket screws back in the servo before insta😅lling servo on car.
@harborareatech310 dude, I fought forever with that back screw. Then I looked at the new servo and said "wait a minute" lol I can just take the mount screws out. You have to lay on your back to get the bottom one next to heat pipe. Took me 5 min to get servo out and new one in if that. They're machine screws. So like I said. Once you crack loose you can spin out with your fingers, hands must be dry and not slippery. Put them back the same way. Try it out next time.
@Vergitas623 If you catch it in time the dealer should cover it according to the bulletin/service campaign. If not it can be a bit costly. Always consult your local dealership for more information before anything!
@harborareatech310 Dang... I'm SOL. Mine is a 2016... 80k. Haven't had much luck with the servos... I'm in Arizona so the plastic are always falling apart. Replaced 2 of them on my Jeep and the Lexus IS just took a shit.
So definitely call the dealership before attempting to repair this yourself. I just called this morning and explained my issue and they said this is covered up to 125000 miles. I have a 2017 is350 f sport with 58000 miles. I'm taking it in tomorrow for repair.
Yes, that's the first direction to go! The customer support program covers vehicles 7 years from first use or 125k miles, whatever comes first. So you should be good
hey brother thanks for the video, would it be possible if you can send me the repair manual? i'm from Saudi arabia and the dealership is very expensive here and i like to work on the car myself. have a good day.
Thanks for watching. Unfortunately, i can't send the repair manuals. I dont do it the repair manual way anyways. The repair manual asks to remove the whole ac box, which is labor extensive. I do it the work smarter, not harder method.
Yeah i have the same car sorry for not mentioning it but how is it to remove the one on top driver side ? I need to remove the underneath dash under the steering and ?@@harborareatech310
My driver and passenger are bad make a video for the driver side lol they trying to charge me $1800 dollars!! Passenger side seems simple is the driver side similar???
The driver side is easier. same concept, just on the other side, i will make a video when the opportunity arises. But it depends on what trouble code you have recorded
Ok so b1454 applies to the servo motor in this video and 1455 applies to the servo motor right above the one in this video. Refer to 7:32 for the location
How much does cost to do the job I have 7 codes The car haves cold ac but passenger side coming hot air It only throw air trough the windshield any help ?
![I.N "HALLUCINATION" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/n5B5q1Hwt_U/mqdefault.jpg)
Apprecaite the videos brother. My passenger side blew hot air and i knew it was the blend door so i just closed those vents. I accidently turned the heat on the other day and now nlboth sides are hot. Are both motors accessible like what you showed in this video? Than you.
From what i have gathered, i have the B1443 code on my 2015 Lexus IS, from what i got from Techstream , i've read your older comments.
its the driver side, biggest one on top
- removal of the driver knee bag
- removal of some trim pieces around the dash console
- disconnect battery for 15 minutes before starting
anything else i should know before starting/ do you have any videos of it? thanks!
Dude you are awesome, mine just went out today. Your video was perfect., very detailed and well executed
Thank you!
Thanks!
No problem. Thank you !
It’s about time you release something from the archives!😁
Serio. 😅
Informative, articulate, perfect video. Thank you.
@@michaelbella8752 thank you
Thank you for this video I have a is2008 haven’t had any AC issues yet but this is good to know of this problem
Thanks for watching. I don't think the 2008 model IS350 or IS250 have this campaign. It's on the 2013 and up. But if the servo motor does go out this is a similar process for replacement!
Thanks! I fixed my GS350 with this video!
@@mostafautd glad it helped!
Hi harbor im having b1455 saying driver side but when i check on the hvac manual it shows me number 10 on the passenger side just on top of the one you did on this video can u explain me? Thanks man your the man.
B1455 is the one on top of the one that was replaced in this video. It is known as the DEF AO servo pulse (D)
@@harborareatech310 thanks for responding! have you encounter with b1455 ? Is it easier to change ? Im losing my mind i dont hve warranty 🥲
@richyvan1511 yes I have encountered it. Same process as the one in the video not too difficult
@@harborareatech310 thank for nswering!
@ last question your telling me is on passenger side but when i check error code says Air Outlet Damper FOOT / DEF Control Servo Motor Circuit ( Driver Side )
I'm going to attempt to do this during the weekend, thanks for the awesome visual of where it's located. The dealership wants 2300 to replace it.
@@FrankEstrada-s6uheck yeah it's not bad at all. there a multiple servo motors. Make sure the trouble code matches servo motor being replaced
Wow this was the best details Video on UTube
Thanks for watching!
If i do a battery change will i need to reset the AC servo motors?
Thank you for the very informative video.
The service manual says that servo motor initialization is a necessary procedure when disconnecting/recomnecting the battery. Whether it makes a huge impact, i personnaly dont think so, but it does state that it may effect/inoperative funtction when necessary procedures are not performed.
@harborareatech310 appreciate the response and your knowledge good sir :)
Great video, my 2018 is f sport have this problem few days ago.
I brought the diagnose tool, gonna to re calibrate it. If it doesnt work, will replace it.
But my car is right hand drive, hope that servo motor can be easily access.
@@mst563 heck yeah ! Its should be easily accessible just a mirror view since it's right hand drive
@@harborareatech310 Actually my driver side blow hot air, not the pax side.
The far right vent is much hotter than the middle right one.
Can you give me hint that where's the servo motor for controlling the temp. of the driver side?
Is it inside the middle console beside the knee?
Or wherever which side blow out the hot air, it's the same servo motor?
@@mst563 I would start by scanning the vehicle for any diagnostic trouble codes
@@harborareatech310 you right🤝
Great video, able to show replacement vid for B1453 and B1455, having driver's side blowing hot air issue and no warranty given by dealer.
When the opportunity arises I will. The concept is the same just on the opposite side. Those are easier to replace as well
Did you ever upload the video for the other side?
@@erickespinoza6998I’m having this same problem with my is350 right now I scanned it and it says driver foot servo motor circuit did u ever figure out how?
Can you please make a video on how to change the air outlet damper cool contorl servo motor? My ac is blowing hot air. It’s from the passenger side it’s so high up I can’t reach it
@@KoolieBhaidid you get a check engine light?
Because my 16’ IS 300 with 66k miles is blowing hot air
But no check engine light
Could you possibly post more servos replacement videos if you get any more for the IS
Hopefully I get the chance to post more servo motor replacement videos
Why hasn’t Lexus extended this coverage tonight NX models? I have 3 that are failing in my 2015. Same years as all the others, quoting me 2400 to fix.
@@ShutUPAndPlay64 🤷🏻♂️
Very helpful! Thanks very much!
Thanks for watching!
what year u doing is350 ?? mine 2017 RC200t F sport have this problems too will get techstream and start order new servo motor working on it soon
I think this was a 2017 is200t but it's affecting a number of lexus vehicles
Awesome video!!!!
Thank you
Just dropped off my 2017 IS 350 for the exact same issue. I got a letter from Lexus indicating my warranty for the AC was extended 7 more years or 125k miles
Thats whats up!!
@@harborareatech310 The Lexus El Cajon dealership had 2 LFAs in their show room. One being a Nurburgring Ring edition ONLY one in red over 2 million dollar car (the only red 3P0 LFA) 🔥 the other one being a red LFA. So BEAUTIFUL….!!!
@HAULUUZ If im ever in that area, i will have to make a stop for that!
How long did it take to replace it? need to get mine replaced 16 IS 300 66k miles
Great video! I just noticed my RC350 was doing this about two months ago. Seems like a project I can handle.
Question: I have that nasty smell when I first turn on my A/C. I can't do the evaporator cleaning where you spray cleaning foam using the drain line due to it being on top of the transmission. Would I be able to do that cleaning when I replace the servo? Is there a spot I can insert the spray or would I have to drill a small hole then plug it after?
Thanks!!
Thanks! Always check with the dealer first to see if you're covered. If not, refer to the trouble code to see which servo motor is at fault.
On your vehicle, it shouldn't be that hard to replace them.
To answer your question, I dont remember off the top of my head, but you may have an access view of the evaporator through the inside of the vehicle toward the firewall center area on the passenger or driver side. If so, you can spray the evaporator through there. if not, you can always spray the outside cowl area with the a/c on max with the fresh air mode on and all windows closed. Then, always replace your ac filter with the charcoal style one, and when turning off your vehicle, ALWAYS leave your ac on fresh air mode to prevent excessive moisture buildup. That is what causes that mildew odor.
@@harborareatech310 Thanks for the quick response!! I'll check and see if the evaporator is visible or not, I want to say I've tried this before and could not see it. I saw at the 12:30 mark, a small white plug-looking thing. If I can't access the evaporator, I'll check to see if that is a plug and reply back. Thanks again and hope you are able to enjoy your weekend and not have to work like me, lol
So I was able to access the evaporator by removing the glove box, etc. I removed an adapter that was used for the floorboard a/c and from there I could see right into the evaporator. The only thing is you have to have the a/c settings set to Floor before turning off the vehicle so the floor port opens up. After that, I was able to spray the foam cleaner in there. What a difference. So glad I found your video! Thanks again!!
What did u do to get rid of the smell?
Mine does that when I turn the ac on
@leojohnwayne1422 after I took apart my glove box and everything above, I used Nextzett Klima Cleaner. One can was more than enough. After I did this, my a/c had zero smell.
Thank you so much for this video! I have a 2015 Lexus IS350 f sport and have the same problem . I will order a new A/C Servo Motor and do it... btw What scan tool you are recommend to buy? again thank you so much for the GREAT video.
Thanks for watching. I used the vehicle manufacturer scan tool (techstream) in this video. If you do not own a scan tool, i would suggest borrowing one or looking online "how to download techstream on a laptop " and just buying the data link connector to connect to your vehicle.
@michaeldao1711 I have the same year and model.. can you pls let me know the part number that you ordered (A/C Servo Motor) for Driver and Passenger side ? thank you in advance
@jonatbass1111 part numbers vary. it all depends on the active troublencodes that are stored in your vehicles module
B1446 (do I need to change this?), B1453 (D), B1454 (P)
@jonatbass1111 these parts are for IS models 2014and newer b1446 part numer 87106-30570 location is driver side lowest servo motor on the hvac box.
B1453 part number is 87106-30610 location is on the driver side middle servo motor on the hvac box. And b1454 is the same part number as b1453 but is located on passenger side ( the one i replace in the video). For location you can refer to 7:29 of the video.
You said the servo motor needs to be lined up with the flat spot on the AC box, yeah? Do we line it up by turning the flat spot on the AC box or turn the "gear" on the servo motor? Or it doesn't matter? Thanks.
@ezyoffice Do not move the gear on the servo motor. Doing so will damage the servo motor. Adjust the gear on the A/c box for proper alignment
@@harborareatech310 Got it.. your videos have been very informative, subscribed!
I’ve had the hot air issue resolved by the dealership but now mine gets stuck on defrost mode. The dealer states they fixed but continues to happen. Can you explain what servo motor or blend door actuator controls this function ?
I brought my 2015 IS350 in for this exact issue... Just was called that it is $2400.. The only difference is it is the drivers side... Looks like number 6 from your document.... Question is.. Can this be done without that diagnostic tool that you have? Looks like it needs to be reset/programmed after the new one is installed.....
You can replace the servo motor yourself, always refer to the stored trouble code in your vehicle to know which is the servo motor affected. You may have better results after just replacing the affected servo motor, but in order to have the optimum A/C performance, the initialization is required.
@@harborareatech310 Thanks.. I just ordered a cable from Amazon and when it gets here I will download the software and try to use it that way... I am also trying to get my service advisor to call me back.. Have read a few things about how long it should be covered.. I have had this at Lexus 3 times already for this over the years and all they have done in the past was to "reprogram" the computer.. Seems to happen every year when the AC is actually shut off for a few days.. South Florida we use AC a lot :)
@joelee5493 thats a good idea! in order for it to actually qualify for the extended service campaign repair, the servo motor troble code needs to be stored and active after the reprogram. sometimes, the reprogram takes care of it. Maybe that was your case in the past. From what i noticed, hot areas are affected the most by this issue.
@@harborareatech310 After the cable gets here that is the plan. Since this has happened before... question is, what bad would it be if replaced them all since the dash will be taken apart already??
@@harborareatech310 I will try it just in case.. If it doesn't work I still take the dash apart. Not looking forward to that but it is def better than paying $2400
Hello, great video. I was wondering if the process is similar on a 2013 GS350 AWD. I have a code B1443 and dealer says $2400 to replace bad servo motor. I missed the recall period because I wasn’t aware of the bulletin. Is that motor also accessible without pulling the dash? I would love if you could do a video on the GS350. A few other members in our GS facebook group is also interested in this. Thanks.
Hey, thanks for watching and the comment. I will try to answer as best as i can. It has been a while since i ve replaced that one. But i believe you can do all servos on the GS 350 without removing the dash. That is the largest one on the driver's side, and i believe it is the same concept as the one in the video, if not very similar. If the opportunity arises, i will make a video. If you are local to the los angeles CA area, i can make a video for the GS community.
Wow, I’m so impressed on your quick response. I wish I was in LA, but unfortunately I’m in Boston MA. Any additional information on how to replace would be greatly appreciated. If you know the part number for the servo motor would also help. I’ll also check in the user group if anyone having this issue is in the LA area. Thanks
@@harborareatech310can I please get your address
Hi you guys. I'm in South LA and I need my servos serviced. Can I volunteer my 2016 gs for the video? Thanks in advance regardless. Great video bro. 👍
Greeting good sir, where do you find this repair manual? I’m looking to purchase one for Lexus NX and RX series! Any tip would be greatly appreciated. You’re awesome
I have manuals because I worked at the dealership. If you want repair manuals you would probably sign up for some sort of autor repair database like All Data or Mitchell.
Awesome, thank you.
@yonathanbehailu4185 No problem, thanks for watching!
Nice video, I have a 2016 gs350 driver and passenger take turns being hot, cold or won't blow at all. I did replace my battery about 6 months ago but i didn't notice a problem right away. I noticed it after being out of town for a couple weeks without using the car. You said the servo motors are supposed to be re-initalized, does that have to be done at the dealer or can i do that another way like with a Blue Driver obd tool?
I would check first to see if it is covered by the dealer. There is a secondary coverage customer support program that a lot of lexus vehicles fall under this program. i believe it's 7 years from the date of first use or 125k miles, whichever occurs first.
To answer your question, though, a more advanced scan tool is required to initialize the servor motors. You can always download the lexus/toyota software "techstream" on to your laptop by looking it up. You would just need to buy the obd cable to connect from the laptop to the vehicle.
@@harborareatech310 Thank you, really, thanks it's appreciated. Obviously you're a good tech with a knowledgeable and accurate answer.
I guess even if I bought a servo motor, there are multiple and I wouldn't know for sure which to buy?
And lastly, even if I get the right one and I replaced it, then it won't work right because it needs to be initialized?
@mattdi333 you need a scan tool capable of retrieving trouble codes from the body control module to determine which servo motor is at fault. After replacing the servo motor, if you dont intialize, you won't experience optimum perforformance
@@harborareatech310thanks again, it is much appreciated.
Subscribed also, good content from a good guy.
WHAT KIND OF TOOL DID YOU USE TO REMOVE THE PHILLIP SCREWS ON THAT LITTHE BOX CAUSE I HAVE NO ROOM TO REACH TO IT , HELP PLEASE
1/4 in Ratchet with a phillips socket and a bit wrench ratcheting tool. My bits are magnetic, so it helps a ton
7:55-8:55 i show the tools i use
I have a rc 2019 my servo #1 87106-30510 is going bad Lexus quoted me 3k+ to replace it. I’ve bought the servo that’s going bad and I want to replace myself but if I disconnect the battery is anything else going to deprogram? Also if I replace the servos myself is it mandatory that they need reprogramming?
@josephribs if you disconnect the battery and/or replace a servo motor(s), they would need to be initialized for optimum performance. If not, they most likely would work but not at its best performance. Ch3ck out my video ruclips.net/video/Ad2X1XXt3Sc/видео.htmlsi=-8IJsXdISHzg2Yxp This is an affordable scan tool I recommend al toyota and lexus owners to have. It is capable of performing the servo motor initialization and many more functions.
@@harborareatech310thank you I appreciate it!
Hello I just took my RCF to the dealer for this same issue, looks like it’s not covered under warranty anymore. I have trouble codes B1441, B1443, & B1453. They said the dash needs to be removed as well is there anything you recommend to avoid that or which servos to replace
@Loudbasshead_ I don't remember the RC-F off the top of my head, but I believe it's similar to RC. If so, it can be done without removing the whole dash . Accordimg to the codes you gave me, you have 2 servo motors on the driver side, and one on the passenger that are at fault. I would recommend changing only the servos triggering active trouble codes
@@harborareatech310thanks for the reply! Would you happen to know which ones exactly to buy and replace Lexus is charging over 2800 and sadly out of warranty with the CSP
How many servos are in these cars? Yours is the only one I can find but it's only for the passenger side
@@peterthiphavong2721 I believe it has 7 servos
Are the 3 motors shown in the video during the repair accesible to replace without removing the entire box? And for the driver side as well? Thanks in advance!
Yes
Does this cover the servo motor problem im having with two motors on my is 250 2014 f sport...the dealershp wants 3k for repair...91,000mi on vehicle
Check with the dealership some vehicles have an extended warranty
Dang! I will always try to avoid the STEALRship 😂. Sometimes you have no choice..
Wow 3k dollars sheesh, I have 58,000 miles on my 17 is350. Thank God it was covered by Lexus warranty.
I am having this problem in the driver side vent. Any advice?
First, check with your local dealership to see if your vehicle either falls under the technical service bulletin or service campaign. If it does, then the repair will be covered through them. If not covered, then you will need to obtain the trouble codes recorded in your vehicle in order to see which servi motors are affected
Ive taken my RC in for the recall, both centers were blowing hot while AC was at 68. They fixed it but now I'm back to all driver side vents blowing hot and all passenger vents blowing cold. Is this still covered under the recall, or do I need to pay to replace the servos? And which servo is it for the driver side? just want to prepare my bank account if payment is due lol
The service campaign is 7 years 125k miles
Any chance you have a video on how to replace this for a 2015 RX350?
I dont at the moment, but when the opportunity arises, i will make a video.!
@@harborareatech310thanks man 👍
Hi, just wanna pick your brain, if the error code is B1453 as shown on techstream, on a RIGHT-HAND drive car (Japan), is it still the same servo motor on the left side of the vehicle? Does the error code mean different part for RHD vs LHD or is it the same, regardless?
@ezyoffice I never worked on the right hand drive version, but my educated guess is that it would be located on the opposite side of a LHD vehicle
@@harborareatech310 Yes, turns out you are right, mate. In your video, you done it on the passenger side, in your opinion is it easier or harder to get to on the driver's side? Also, can I just simply unplug it after re-initialization so that it doesn't ever blow hot air?
Hmm... read through the bulletin and it seems that there is a need to flash a new calibration to the ac amplifier and that would solve the servo motor issue? Instead of replacing them.
@@ezyoffice around 5:20 I explain the bulletin procedure from my experience the ac amplifier reflash doesn't always solve the servo motor issue
Hello ,any chance you can help me by pointing out where to find B1443 servo on RHD/UK model,is it passenger or driver side?I sourced the code and it's 43 displayed on the climate control , symptoms no air going through console vents and no memory stored for AC.Thank you in advance.
What kind of vehicle do you have?
@@harborareatech310 2014 lexus is300h,as mentioned in my previous comment it is UK model. From what I could find it looks like AC unit has to come out to access this particular servo , according to the lexus bulletin.Thank you for your reply, appreciate it .
@@harborareatech310 just a quick question , according to service report from August 2018 the fault was already there,no air blowing out of the vents ,it only blows on the windscreen,feet won't get air too.I am the third owner ,first owner had this issue diagnosed while the car was 4 years old and 62 k miles on the clock by Lexus .Do you think I can have a foot to stand on and try to chase them to fix the issue? He paid for extended warranty and there are loads of service reports but none about this issue being fixed .
@michalnowak3558 I'm not sure about that vehicle. We dont have that model over here. But if it's anything like the IS350, it will be on the driver side top servo motor, which is the biggest servo motor. It can be done without removing the whole dash, only the driver side knee air bag, and a couple of covers need to be removed. You can try to contest the issue at the dealer, and if you are persistent enough, they might goodwill the service, but it is not guaranteed.
will this also fix this mode issue?? I have issue with mine mode not changing mode correctly and blowing air everywhere except where I wanted. If so do I need to replace all 3?
@@Arcanny certain servo motors do affect the mode operation. The vehicle will need to be scanned and properly diagnosed to see which servo motor(s) are at fault
@@harborareatech310 thank for the reply!! will the techstream detect that? if I'll get one
Hello. Do you happened to know where is the mode servo piece located at. Im having issues with my 15 lexus rc350 with the mode switch not properly working right
Give me a trouble code, and that will give me moe info to answer your question.
i will let you know once I have a chance to get back to my car
@@harborareatech310I have this types of Code stated as history
B1442
B1443
B1453
B1454
B1455
B14B2
B14B5
U0163
@@harborareatech310 I have a question. If anyone had this issues please comments. So far this is all my trouble code due to my Air conditioning. My problem was the air coming out from all vents blowing to my face with LO(60 degree temperature - until I changed to heat temps. Both of my Driver/passenger vents changed to blowing to bottom. It went bad when I changes my temperatures to cool and my air vents wont blowing like it before i changed to heat. Sorry for the incorrect sentences. Please any advices would help.
great video , by the way did you unplug the battery?
Thank you! Yes, prior to performing the removal and replacement procedure of the servo motor, the battery must be disconnected, as seen in 8:47
and how did you put it back in , did you remove the white spin thing out b4 install it
14:15 shows a diagram on how to align
So you are saying, even if we replace the servo. The car still needs to be taken to the dealer for programming?
No, if you replace the servo, you just need to make sure you are equipped with a scan tool capable of performing an ac system initialization. For optimum ac performance
@@harborareatech310
You are a great dude! Appreciate your input. Interested in earning my business?
i have code 41 on my is250 2015 is that the servo motor?
So there is a much easier way. Loosen the 2 little silver screws all the way, that are on the outside of servo that you can see.
This releases the servo from the mounting bracket. Then remove mounting bracket from new servo and install back on Car on old mounting bracket.
Once you break the screws free which is very easy, you can remove and reinstall with your finger tips then snug up with Phillips. Sooooo much easier!
Note slide the long mounting bracket screws back in the servo before insta😅lling servo on car.
@bliffblam interesting, never done it that way
@harborareatech310 dude, I fought forever with that back screw. Then I looked at the new servo and said "wait a minute" lol I can just take the mount screws out.
You have to lay on your back to get the bottom one next to heat pipe. Took me 5 min to get servo out and new one in if that.
They're machine screws. So like I said. Once you crack loose you can spin out with your fingers, hands must be dry and not slippery. Put them back the same way.
Try it out next time.
@@bliffblam Glad I saw your comment, I did exactly what you said, for those DIYers, save yourself the ache by removing the bracket screws instead.
@ezyoffice cool. Definitely makes a huge difference. Glad I could help
How much does it cost to replace air conditioning servo motor for is 250 ( 2010)? Thanks
Depends where you take it!
The warranty is good for 4 years or 50,000 miles
@PK-eb1mw that is true and there is also a customer support program that covers the servo motors for 7 years or 125k miles whatever comes first
i have a 2019 lexus is300 with 16000 miles and have this exact problem..do you know if its covered under warranty.
Call your local dealership to find out. They can look up your VIN number and find out. It might fall under the 4 year 50k mile basic warranty
4 years 50k miles warranty
6 years 70k miles power train
Do I need a scan tool to initialize servo?
@@Jp-ub3ci yes
I have a 2018 Lexus IS300 amd just had to have both of my actuators replaced
Nice !! Was it covered by the dealership?
How much was this fix?
@Vergitas623 If you catch it in time the dealer should cover it according to the bulletin/service campaign. If not it can be a bit costly. Always consult your local dealership for more information before anything!
@harborareatech310
Dang... I'm SOL. Mine is a 2016... 80k. Haven't had much luck with the servos... I'm in Arizona so the plastic are always falling apart. Replaced 2 of them on my Jeep and the Lexus IS just took a shit.
Hi I’m out of warranty with dealer by a couple months. Do you have a shop where this can be done? Thanks!
email for more info mercado.saul@yahoo.com
Hi can i just disconnect the motor without replacing it??
Yes, you can, but I don't see why you would do that
@@harborareatech310 if I disconnect it wont it be cool ???
@@saifoalfalahi4905 it will be most likely the same
My servo motor went out, Lexus dealer fixed it free of charge due to servo motor falls under part warranty.
Nice!!
@@harborareatech310how do you avoid dropping the back screw?
@@gomezpmm302 balance. But if you have a magnetic bit that helps a ton.
No labor cost ?
What’s the part number??
The part number for this specific servo motor can be found at 7:48
Is this the same part number for the 2018 is300? Im going to do this fix before the summer hits.
yes@@NIRVANAxOWNS
So definitely call the dealership before attempting to repair this yourself. I just called this morning and explained my issue and they said this is covered up to 125000 miles. I have a 2017 is350 f sport with 58000 miles. I'm taking it in tomorrow for repair.
Yes, that's the first direction to go! The customer support program covers vehicles 7 years from first use or 125k miles, whatever comes first. So you should be good
@@harborareatech310Im having the same issue on my 2016 IS 300 AWD 66k miles
I received the same recall coverage
Will they replace the compressor?
How much do you charge to do this?
Depends on the vehicle
Hello ?
How r u doing ?
Are you a mechanic from Houston Texas?
Doing well thanks for watching! No I am not from Houston.
How much do they charge for that?
If it's not covered under warranty or the extended service campaign, this repair can be very costly
hey brother thanks for the video, would it be possible if you can send me the repair manual? i'm from Saudi arabia and the dealership is very expensive here and i like to work on the car myself. have a good day.
Thanks for watching. Unfortunately, i can't send the repair manuals. I dont do it the repair manual way anyways. The repair manual asks to remove the whole ac box, which is labor extensive. I do it the work smarter, not harder method.
What city are you in?
Los Angeles
@@harborareatech310 I wanted to go to your shop tomorrow
@edwardcastillo9895 i dont have a shop, but if you are having this problem contact me at mercado.saul@yahoo.com
dont you hate when people bring cars in with low fuel and sometimes they ask why didnt you fill it up
Yes i do
I have a 2016 so I have to pay, I’m only at 60 k miles tho 😢
i think that i have the same issue
I wouldn't doubt it it's a very common issue
So is this covered by Lexus?
Check with your local dealership.
@@harborareatech310 I'm gonna call I have a 2014 is350, AC only blowing thru the windshield vents only. Hopefully Lexus will fix this
Where is located b1443
Every vehicle is different, but on this vehicle, it is the top one on the driver side of the A/C box.
Yeah i have the same car sorry for not mentioning it but how is it to remove the one on top driver side ? I need to remove the underneath dash under the steering and ?@@harborareatech310
My driver and passenger are bad make a video for the driver side lol they trying to charge me $1800 dollars!!
Passenger side seems simple is the driver side similar???
The driver side is easier. same concept, just on the other side, i will make a video when the opportunity arises. But it depends on what trouble code you have recorded
@@harborareatech310 The codes are B1455 and B1454
Ok so b1454 applies to the servo motor in this video and 1455 applies to the servo motor right above the one in this video. Refer to 7:32 for the location
@@harborareatech310 bruh you are a life saver ahah it’s pretty crazy that they charge 6.5hours to repair this
@@dariomartin7453Yeah, that is crazy. They're taking into consideration that the airbox needs to be removed. But we we work smarter not harder
Dealer told me my warranty expired in 2022😢 this problem just started happening on my 2014 is350.
That's unfortunate. But the good thing is that this is not a difficult repair
@@harborareatech310they quoted me 2700$ for the repair. Time to get rid of her 😢
How much does cost to do the job I have 7 codes
The car haves cold ac but passenger side coming hot air
It only throw air trough the windshield any help ?
All depends on the vehicle. i would first check with your local dealer it may be covered under the service campaign
Thank you. Very helpful!
Thanks!