bonjour, comment savoir si ce point CLK et HS, j'ai une oled qui refuse de démarrée de charger malgrès le remplacement de la puce BQ et MT9236 et P13 qui fonctionne, ou le problème viens t'il d'ailleur mais comment savoir merci d'avance pour votre aide
Comment t'as fait tenir ton cable entre l'eMMC et la carte mère, je vais faire l'opération sur une carte HS et j'aimerai savoir si t'as des conseils ? Je suis étonné que quand tu as mis ton heat gun le cable soit pas parti à perpet parce qu'il était pas fixer avec de l'UV Mask T'as une technique particulière ou alors t'as juste eu une giga chatte ?
Hello, sorry for the question, but, this break in the track, results in the console not being able to enter the system, like, just give a Nintendo screen and not enter the system?
It is enameled obviously. The board made a connection with the wire that made a connection with the chip at the very least. Most likely that the board also made a connection with the board itself.
hmm... I think I might try this. I have a custom 0.6mm board to go between the main board and emmc, that breaks out a few of the points, dat0 and clk being two of them. I ruined the clk point on my first chip attempt (before I had a better microscope) much like the one in this video. Was successful on my 2nd try, but the first is still laying around to be used later for parts. Would be a bonus if I can get it working...
Un génie, j'adore, toujours satisfaisant ces vidéos, good job.
bonjour, comment savoir si ce point CLK et HS, j'ai une oled qui refuse de démarrée de charger malgrès le remplacement de la puce BQ et MT9236 et P13 qui fonctionne, ou le problème viens t'il d'ailleur mais comment savoir merci d'avance pour votre aide
Bonjour j’aimerais savoir quand je vais récupérer ma console , je l’ai envoyé le 31 janvier
I connecte the dat0 to point B and now my switch OLED don’t boot ofw ( black screen ) and no boot CFW ( black screen ) do you have solution ? Thanks
Comment t'as fait tenir ton cable entre l'eMMC et la carte mère, je vais faire l'opération sur une carte HS et j'aimerai savoir si t'as des conseils ?
Je suis étonné que quand tu as mis ton heat gun le cable soit pas parti à perpet parce qu'il était pas fixer avec de l'UV Mask
T'as une technique particulière ou alors t'as juste eu une giga chatte ?
Hello friend, a question, in the photo you put at the beginning, the ones that are not marked, what function do they do?
Hello, sorry for the question, but, this break in the track, results in the console not being able to enter the system, like, just give a Nintendo screen and not enter the system?
The console is unable to turn on when the line is cut off.
Impressive. Is that coated(enameled ) wire or pure? and what is its diameter. I wonder how solder balls touched the board properly with that wire.
It is enameled obviously. The board made a connection with the wire that made a connection with the chip at the very least. Most likely that the board also made a connection with the board itself.
How much does this particular job cost?
hmm... I think I might try this. I have a custom 0.6mm board to go between the main board and emmc, that breaks out a few of the points, dat0 and clk being two of them. I ruined the clk point on my first chip attempt (before I had a better microscope) much like the one in this video. Was successful on my 2nd try, but the first is still laying around to be used later for parts. Would be a bonus if I can get it working...
😆😆👍👍👍👍
Quanto Graus sobre o eMMC?
Bravo
Du coup tu va lui pucé maintenant quelle est reparé
C'est l'idée oui ;)
not a very clean work.. but apart from that it work.
Extremely dirty work and workplace.
Thank you for your useful comment and advice !
SCAM
Pk
the fuck are you talking about lmao