Hi, you mentioned that the step can also be performed using a DC power supply with an XR power cable. I am trying to avoid purchasing an additional battery that I will not use otherwise. Could you please provide more information on the type of cable required and where it can be obtained? Thank you very much.
I am using a Qianli iCopy Plus 2.1 and I am trying to perform battery data correction on an Iphone XR battery. When I connect the XR battery to the iCopy Plus Board, I can see the green LED light (connect) comes on to say that there is connection. But when I click 'READ' on the Qianli Repair Helper Software, I keep getting the message "the battery data is not charged. Please insert the battery". So the iCopy is not reading the battery. Do you know why this could be? Thank you.
Hi Matthew, this happens because you didn’t activate your battery. To activate the battery you can plug it to the iPhone and charge it for 1 minute (as seen in the video). After that, you can reset your battery data. For iPhone XR battery if you use iCopy Plus 2.1 you can avoid to use QianLi software: connect the battery to iCopy and wait that battery data is read, then keep pressed for few seconds “READ” and then for few seconds “WRITE”. You will obtain a 100% and 0 cycles battery
Hey I live in Jamaica and I changed my iphone XR battery today and be seeing the error message but I dont think the technicians here in Jamaica can do what I see in your video , what can I do to fix it otherwise??
Hello, great video :) I did this with an iphone XR got the 100% health and 0 cycles but i still see a message that says that the battery is degraded. How do i fix that? thanks
Thanks for the great video, I did this on iPhone xs but it shows battery error message after swapping the BMS and changing the cycle and efficiency values. How can I solve this please? Will a factory reset of iPhone xs help?
Hi, you forgot maybe to connect to the iPhone the copy battery before then the original one (step 5) We recommend you to factory reset with a non genuine battery, activate iPhone, wait for the “error message” and only after it, install the new genuine battery.
@@armza9975 hi friend, we mean “new not genuine battery”. It must appears the error message. This is needed to reset the read of the % and cycles battery on the phone. If you don’t do that, you will continue to see the old % and cycles battery, even if you modified it with software.
this method can work with no-OEM batteries which have a higher capacity? Should modify the mAh values on QIANLI? if not, the battery can work without issues and not affecting the battery life? thanks in advance
Hi, we don't recommend to do this with higher capacity battery cells. The original BMS should work with same original specific parameters. If not, for sure you could face some issues (for example maybe the % of battery life show is not true). So we suggest you to use a same as original mAh new battery
Salve Una domanda Avendo preso un iPhone XR ricondizionato e non monta una batteria originale Apple ma una commerciale da il messaggio di errore. Io ho acquistato un altra batteria commerciale e tramite il programma 3Utools sono riuscito a trovare il vecchio seriale della batteria originale Apple sono riuscito a copiare il seriale sulla nuova batteria però mi da ancora il messaggio di errore perché?
Buonasera, ahimè non è sufficiente riscrivere il seriale originale al fine di non far comparire il messaggio d’errore. Fosse così semplice verrebbe meno la necessità di effettuare lo swap della BMS originale 😉 Affinché non compaia messaggio d’errore è necessaria la BMS originaria di quel device con, ovviamente, il suo relativo seriale originale. Speriamo di esserti stati d’aiuto 💪🏼
Hi, this work also with iPhone 11 but it will fix only the error message. The % battery health will not be fixed with this method. From iPhone 11 you need to add a special flex. We did a video also for 11 series. You can find it in our channel.
Bro i follow all the right steps I edited the battery health and try to power on the device with a power supply before i put the new battery with the bms board. But the battery health in the iphone is different
Hi, once you power on the device with power supply it show the battery error message? If not, you have to wait that the “important message battery” show on your device. More: if you connect the new battery with original BMS to icopy, it show you the new calibration data (I guess 100% and 0 cycles) or the old one?
@@e-pol it already shows the notification. And it reads 100% battery health and 0 cycles on the qianli. But after i installed it on the iphone after the power supply test. It will change the battery health to 85 instead of 100 The original battery health is 79 before the repair
@@techvlogsph4909 ok understand. I suggest you to calibrate again the battery health setting 110% in the QianLi software and then set again 100%. During this operation, please never modify the mAh data of the battery. Keep us updated 💪🏼
Okay bro ill try it next time. The customer had agreed on the situation of 85% batt health. He just want to retain his original bms board. Next time ill try bro ill update you thanks a lot
@@techvlogsph4909 it may be possible that on the next iOS update the battery reading will be fixed at 100% 😉 if happens again, calibrate and calibrate again battery data as I wrote you before, you’ll see that you will not have any issue. Thanks for contacting us 💪🏼
Hi, thanks for suggestions. For a better quality you can watch the other video (iPhone 11-12 battery replacement), the soldering step is the same. This is the link: ruclips.net/video/hCY0awewEVs/видео.html
Hi, this happens because before to install the new battery you should connect a copy battery (Step 5 on video) or connect a power cable, or because you didn't modify the battery data
@@e-pol I Have Make This Step But the % dosn't change and i change on the QIANLI the % to 105% and back to 100% (no change Mah) a lot of time but nothing
Thank you for fixing my phone. You are so talented!
Hi, you mentioned that the step can also be performed using a DC power supply with an XR power cable. I am trying to avoid purchasing an additional battery that I will not use otherwise. Could you please provide more information on the type of cable required and where it can be obtained? Thank you very much.
Hello, if you use DC then you need a multi power cable like this:
www.e-pol.it/store/product/88863
is it possible to get rid of the error message without the orignal battery flex cable.
if yes then can u please help me out
Hi, without original board you can’t fix the error, we are sorry
I am using a Qianli iCopy Plus 2.1 and I am trying to perform battery data correction on an Iphone XR battery. When I connect the XR battery to the iCopy Plus Board, I can see the green LED light (connect) comes on to say that there is connection. But when I click 'READ' on the Qianli Repair Helper Software, I keep getting the message "the battery data is not charged. Please insert the battery". So the iCopy is not reading the battery. Do you know why this could be? Thank you.
Hi Matthew, this happens because you didn’t activate your battery.
To activate the battery you can plug it to the iPhone and charge it for 1 minute (as seen in the video). After that, you can reset your battery data. For iPhone XR battery if you use iCopy Plus 2.1 you can avoid to use QianLi software: connect the battery to iCopy and wait that battery data is read, then keep pressed for few seconds “READ” and then for few seconds “WRITE”. You will obtain a 100% and 0 cycles battery
Hey I live in Jamaica and I changed my iphone XR battery today and be seeing the error message but I dont think the technicians here in Jamaica can do what I see in your video , what can I do to fix it otherwise??
Hi Maleek, sorry, no other way to fix that error
Hello, can y use iphone x battery ( same connector) for upstart before put the new battery with original board ? Thanks
Hi Eric, no, it's not recommended to do this, even if it's same FPC and even if device would power on
Hello, great video :) I did this with an iphone XR got the 100% health and 0 cycles but i still see a message that says that the battery is degraded. How do i fix that? thanks
Hello Agustin, please try to set 110% on QianLi software. Then try and try again to set the battery data, always connecting a copy battery before
@@e-pol Just did that, tried 110%, connected a copy battery, and then the corrected battery and still shows 100% but with the maintenance warning :(
@@mushi08 please send me picture of the error or screenshot to laboratorio@e-pol.it
Then we try to help you solve it
Thanks for the great video, I did this on iPhone xs but it shows battery error message after swapping the BMS and changing the cycle and efficiency values. How can I solve this please? Will a factory reset of iPhone xs help?
Hi, you forgot maybe to connect to the iPhone the copy battery before then the original one (step 5)
We recommend you to factory reset with a non genuine battery, activate iPhone, wait for the “error message” and only after it, install the new genuine battery.
@@e-pol thanks for the tip. I will try this and let you know how I get on!
@@e-pol Why must we install and use a copy battery (do you mean unmodified spare battery?) before we install the new battery with the BMS board?
@@armza9975 hi friend, we mean “new not genuine battery”. It must appears the error message. This is needed to reset the read of the % and cycles battery on the phone.
If you don’t do that, you will continue to see the old % and cycles battery, even if you modified it with software.
this method can work with no-OEM batteries which have a higher capacity? Should modify the mAh values on QIANLI? if not, the battery can work without issues and not affecting the battery life? thanks in advance
Hi, we don't recommend to do this with higher capacity battery cells. The original BMS should work with same original specific parameters. If not, for sure you could face some issues (for example maybe the % of battery life show is not true). So we suggest you to use a same as original mAh new battery
Salve
Una domanda
Avendo preso un iPhone XR ricondizionato e non monta una batteria originale Apple ma una commerciale da il messaggio di errore. Io ho acquistato un altra batteria commerciale e tramite il programma 3Utools sono riuscito a trovare il vecchio seriale della batteria originale Apple sono riuscito a copiare il seriale sulla nuova batteria però mi da ancora il messaggio di errore perché?
Buonasera, ahimè non è sufficiente riscrivere il seriale originale al fine di non far comparire il messaggio d’errore. Fosse così semplice verrebbe meno la necessità di effettuare lo swap della BMS originale 😉
Affinché non compaia messaggio d’errore è necessaria la BMS originaria di quel device con, ovviamente, il suo relativo seriale originale. Speriamo di esserti stati d’aiuto 💪🏼
@@e-pol grazie mille per aiuto auguri di buona pasqua
ap ki shop kidhar ha
Hi friend, we are based in Italy
Ciao ma per per gli iPhone xs e xs max si usa lo stesso metodo o non si riesce? Grazie
Ciao Thomas, come puoi leggere nella descrizione del video la procedura si applica allo stesso modo anche per xs ed xs max 😉
@@e-pol ok grazie mille
Does this work with iPhone 11 series? If not, why?
Hi, this work also with iPhone 11 but it will fix only the error message. The % battery health will not be fixed with this method.
From iPhone 11 you need to add a special flex. We did a video also for 11 series. You can find it in our channel.
Bro i follow all the right steps
I edited the battery health and try to power on the device with a power supply before i put the new battery with the bms board. But the battery health in the iphone is different
Hi, once you power on the device with power supply it show the battery error message? If not, you have to wait that the “important message battery” show on your device. More: if you connect the new battery with original BMS to icopy, it show you the new calibration data (I guess 100% and 0 cycles) or the old one?
@@e-pol it already shows the notification. And it reads 100% battery health and 0 cycles on the qianli. But after i installed it on the iphone after the power supply test. It will change the battery health to 85 instead of 100
The original battery health is 79 before the repair
@@techvlogsph4909 ok understand. I suggest you to calibrate again the battery health setting 110% in the QianLi software and then set again 100%. During this operation, please never modify the mAh data of the battery. Keep us updated 💪🏼
Okay bro ill try it next time. The customer had agreed on the situation of 85% batt health. He just want to retain his original bms board. Next time ill try bro ill update you thanks a lot
@@techvlogsph4909 it may be possible that on the next iOS update the battery reading will be fixed at 100% 😉 if happens again, calibrate and calibrate again battery data as I wrote you before, you’ll see that you will not have any issue. Thanks for contacting us 💪🏼
Hi is that possible with jc1vs ?
Hi, yes, you can fix battery error also with JC tool. But we prefer QianLi Tools because from ip11 series it’s easier then JC
Bro?? When you zoom 1:38 soldering the video quality is bad… not even see clearly 720 or 480p
Hi, thanks for suggestions. For a better quality you can watch the other video (iPhone 11-12 battery replacement), the soldering step is the same. This is the link: ruclips.net/video/hCY0awewEVs/видео.html
Hi I have the same Problem but i follow every instruction but the % stay to 80% can tou help me
Hi, this happens because before to install the new battery you should connect a copy battery (Step 5 on video) or connect a power cable, or because you didn't modify the battery data
@@e-pol I Have Make This Step But the % dosn't change
and i change on the QIANLI the % to 105% and back to 100% (no change Mah) a lot of time but nothing
@@replaycedijon7651 once you assembly the copy battery and power on the phone, it appears error message?
@@e-pol yes !
You can try to hard reset the iPhone with copy battery, then assembly the new original one
can i use solder welden
Hi, you can use a soldering iron as well, but it's recommended in this case to use a specific solder alloy
the resolution is 140p......