Great job. That's what I need to do is replace my headlight assembly. 1A auto is a huge help when I need to do some work on my cars. Thank you very much.
I replaced the "bulb" without removing the assembly. It is a little difficult to disconnect it and unscrew the bulb, but it is doable. This video was useful for me, though. My car is Nissan Sentra 2006.
Dont have to for pass side headlight repl. But you have to for drivers side! I just replaced a 9 yr old HID bulb w a newer better one I already had on hand form DDM. ALOT better than taking out the battery to gain access!!! Mine is a 2004 Sentra 1.8s.
an easier way to get that housing out is to remove the bumper me and a buddy did it on my 06 sentra when I was modding it just makes it a little more easier
hi. i was wondering if you guys can do a tutorial on installing a right fender and the steel support for the bumper and the bumper itself for nissan sentra 2004. Thank you
Unfortunately we do not have a video for your application. We will keep this repair in mind for future videos. Thank you for watching! 1aauto.com 888-844-3393
Okay so I'm replacing both my headlights on my '04 Sentra and my concern is taking the whole thing out. Would I have to take it out gently but but not too quick?
Thanks for checking us out! Yes, the headlights will need to be adjusted once installed to ensure they are aligned properly. Hope this helps you out! +Carlos Saavedra
+helenaV34 It may be a different procedure on your application. We currently do not have an auto repair video for this particular year, make and model. Thank you for asking. 1aauto.com
The same headlight is screwed in properly, but the rubber gasket isn’t sitting flush against the side fender of the car. I can’t seem to figure out the reason. The other headlight, opposite of it, does this just fine. Any ideas?
What if I can’t disconnect the headlight? The amber light and everything else went smooth but I can’t disconnect the headlight. Corrosion? Could it have arced a welded the connectors together? Rust? There is condensation in the lens which is why I’m replacing it.
I just don't understand how I completely pulled out the red tabs and broke the black plastic to where it's attached ??I tried putting it back in but still won't work . Need to replace the pig tail plug right ?
We currently do not have an auto repair video that covers this particular repair. We'll keep this request in mind in the event that we need to make this repair in the future. 1aauto.com 866-403-3393
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
Great job. That's what I need to do is replace my headlight assembly. 1A auto is a huge help when I need to do some work on my cars. Thank you very much.
Thank you so much! I was having trouble with my bulb because i didn't realize I had to squeeze the tab when taking it out lol! You helped me so much!
I replaced the "bulb" without removing the assembly. It is a little difficult to disconnect it and unscrew the bulb, but it is doable. This video was useful for me, though. My car is Nissan Sentra 2006.
We currently do not have a video on how to replace the fog lights on this model.
How about now?
Thank you for posting. I was able to change the drivers side headlight bulb without any issues on my 2006.
Thank you soooo much, this was so helpful..you guys are the best
Thanks for watching 1aauto.com 866-403-3393
Dont have to for pass side headlight repl. But you have to for drivers side! I just replaced a 9 yr old HID bulb w a newer better one I already had on hand form DDM. ALOT better than taking out the battery to gain access!!! Mine is a 2004 Sentra 1.8s.
Thanks for checking us out. 1aauto.com +spookerr
thank you so much A1very good we apricate it *****
Thanks Mike. Very helpful
Does this installation apply to the 2002 model?
NICE REVIEW & GOOD CAR.
Do they make a led headlight for the 06 sentra
very helpful thanks for sharing!
Thank you for watching!
1aauto.com 888-844-3393
Great video but you don’t tell us how to adjust the lamp. Who can I take it to to adjust the lamp so the beams are correct
an easier way to get that housing out is to remove the bumper me and a buddy did it on my 06 sentra when I was modding it just makes it a little more easier
hi. i was wondering if you guys can do a tutorial on installing a right fender and the steel support for the bumper and the bumper itself for nissan sentra 2004. Thank you
Unfortunately we do not have a video for your application. We will keep this repair in mind for future videos. Thank you for watching!
1aauto.com 888-844-3393
Okay so I'm replacing both my headlights on my '04 Sentra and my concern is taking the whole thing out. Would I have to take it out gently but but not too quick?
Thank you for watchng. If you go slow and steady you shouldnt have
any problems.
1aauto.com 888-844-3393
can you tell me if you have to take the frame out just to change the bulb? thank you
+Randy Ledford You may be able to reach around the back of the headlight to change the bulb if there's room. 1aauto.com
Is there any difference between this model 1.8 version to the 2.5 SE-R Spec V version?
Nope
RGJ 600 Speed?
Do you have to adjust the headlights after installation?
Thanks for checking us out! Yes, the headlights will need to be adjusted once installed to ensure they are aligned properly. Hope this helps you out! +Carlos Saavedra
+Carlos Saavedra We do not offer price matching.
Hi i would like to ask if is the same method as well for nissan almera 2004?
+helenaV34 It may be a different procedure on your application. We currently do not have an auto repair video for this particular year, make and model. Thank you for asking. 1aauto.com
The same headlight is screwed in properly, but the rubber gasket isn’t sitting flush against the side fender of the car. I can’t seem to figure out the reason. The other headlight, opposite of it, does this just fine. Any ideas?
Is the the same setup
What if I can’t disconnect the headlight? The amber light and everything else went smooth but I can’t disconnect the headlight.
Corrosion? Could it have arced a welded the connectors together? Rust?
There is condensation in the lens which is why I’m replacing it.
I just don't understand how I completely pulled out the red tabs and broke the black plastic to where it's attached ??I tried putting it back in but still won't work . Need to replace the pig tail plug right ?
Please do a video for Nissan xterra tunes ups
My headlight is below the bumper after it got hit. What do I do if I can't get it free?
Thanks!
Thanks for the video
No problem. Glad to hear it helped you out. 1aauto.com?RUclips&CTA%20Comment&ATony 866-403-3393
Thank you
Thanks for checking us out. 1aauto.com +Achraf Jellal
Just saved me 800 bucks, that’s how much I’m getting paid for the asshole that messed up my lights
Thank you!
Made a failed attempt pushed back on red tab and red fluid coming out. What is that red fluid?!!
thanks
Thanks for the info.
What about the bottom lights?
We currently do not have an auto repair video that covers this particular repair. We'll keep this request in mind in the event that we need to make this repair in the future. 1aauto.com 866-403-3393
why don't you move the camera ever further and stand even more in front of the headlight
Great
what about fog lights
Very helpful thanks.:-)
Thank you!!!!!!
Thank you for watching!
888-844-3393
1aauto.com 888-844-3393
Good video thank you!
Thanks for the help!
Thank you for watching. Please let us know how the repair comes out!
1aauto.com 888-844-3393
Thanks!
thanks
Thanks!