@@RKGarage think I have possibly found a cure for rev hang in the manual tune too! Set Throttle follower to kph and drop gain values to zero. Hopefully means no more IAC up steps during gear changes
@@RKGarage did you find that it idles high after selecting manual options on enhanced bin? Think I need to adjust some tables but not sure where to start..
hey mate i was watching your other videos and how you said its easier to brick the ecu in the car due to all the modules communicating at the same time. I recall you saying there may be a way to pull the bcm fuse etc to slim the chances a bit better? Just curious thats all, thanks heaps mate
Would I be able to "bench" harness while still in the car? As in unplug the 2 unnecessary plugs and just have that one plugged into ecu and then press Flash PCM on bench on OSe??
Hi mate how much do you charge to do that my Vox commodore will not start I’ve got all dash lights and have everything else but no start I’ve changed my drive module and put a brand new battery in it I put my tester on it and it says the ecu not talking to the engine I’m not sure what’s going on with it
Awesome videos, I'm trying to set up a freestanding vy ecotec, with switch and push buttons start, I'm after a pinout to find what I need to power to make it run, fuel pump wire, ect.. I've got a set up from what you have done here, is that all I'd need to get it going? Can just wire the starter separate? Any help would be greatly appreciated! Cheers
@@RKGarage too easy! So I shouldn't have to get 12v power to, or earth any other pins in the ecu? Aslong as vats disabled and set to manual it should fire up? Cheers! Appreciate it man
Hi do you have any info on tuning the memcal based ECU,s ? (VX V6 Supercharged & turbo) . BTW thanks for all your awesome info, THE BEST by far that I have seen .... 😁👍💪🙌
I have just purchased the ALDL cable and Tunerpro software from Envyous Customs and from what i have found out through PCMhacking i need to purchase a NVRAM first???? thats about all i know so far in regards to the Memcal based ECU tuning .... 😏
@@RKGarage legend my bro just made a bench set up an bench tuned a burble on my vy your video was awesome an helped out heaps an do you know were would I get a bin file for lumpy idle tune churs bro ur a legend
I'm glad I could help. At the moment I'm not releasing my lumpy idle tune as it makes the car a constant flamethrower and is no where near safe nor legal for road use.
@@RKGarage mad respect my bro keep up the solid work be keen if you ever do a lumpy tune that can be road legal im in nz so would have to check laws on that first
Do you have a link can download page from please and If we Remove vats can we just gets the wires an ecu from a wreak flash it an throw in car an drive an keep stock ecu as spair
When doing this in the car do I need to get bin before write bin I'm confused and do I hit yes at the end or no when it says eeprom data In selected bin
@RKGarage yeah I know I can do it in the car but not with my bench flashing harness not sure why I have done everything right I would rather do it on bench can you please help me out
Awesome vid, just made my own harness and it works great! Bricked my first ecu after tryna do it in the car lol. Bench is the way to go
Glad to hear it worked mate!
Yeah they are notirious for bricking when in the car. I went through quite a few!
@@RKGarage think I have possibly found a cure for rev hang in the manual tune too! Set Throttle follower to kph and drop gain values to zero. Hopefully means no more IAC up steps during gear changes
Yeah that is one of the ways I have fixed it before
@@RKGarage did you find that it idles high after selecting manual options on enhanced bin? Think I need to adjust some tables but not sure where to start..
Didnt affect the idle at all
Can you do a video on what you need to do to the ecu to do this and what programs you need?
Awesome work
Need to do absolutely nothing to the ecu, and listed what programs in this vidro, but I can make an even more in depth one if you like?
So this doesn’t have a nvram or anything? Super keen to know more
All stated in this video man, vx,vu,vy n/a are all flash based no memcal, yellow brown plugs are flash based
All pink blue are memcal
hey mate i was watching your other videos and how you said its easier to brick the ecu in the car due to all the modules communicating at the same time. I recall you saying there may be a way to pull the bcm fuse etc to slim the chances a bit better? Just curious thats all, thanks heaps mate
Have never done it myself
I always just bench tune them
Way quicker
Is it the same process with tuner pro RT ?
I haven't got either yet.
Would I be able to "bench" harness while still in the car? As in unplug the 2 unnecessary plugs and just have that one plugged into ecu and then press Flash PCM on bench on OSe??
Pull out the ecu completely
Then yes
meaning i 100% have to make a proper bench harness?@@RKGarage
Yes
Hey mate is it possible to brick the ecu when doing it like this or is it easier to brick flashing it from inside the car??
Easier to brick flashing in the car
Still possible to brick while its on the bench
Hi mate how much do you charge to do that my Vox commodore will not start I’ve got all dash lights and have everything else but no start I’ve changed my drive module and put a brand new battery in it I put my tester on it and it says the ecu not talking to the engine I’m not sure what’s going on with it
Awesome videos, I'm trying to set up a freestanding vy ecotec, with switch and push buttons start, I'm after a pinout to find what I need to power to make it run, fuel pump wire, ect.. I've got a set up from what you have done here, is that all I'd need to get it going? Can just wire the starter separate?
Any help would be greatly appreciated! Cheers
Hey mate, can wire fuel pump and starter seperate. Same as thermo fans 👌
@@RKGarage too easy! So I shouldn't have to get 12v power to, or earth any other pins in the ecu?
Aslong as vats disabled and set to manual it should fire up?
Cheers! Appreciate it man
Did you end up needing the grounds?
From memory, no
Hi do you have any info on tuning the memcal based ECU,s ? (VX V6 Supercharged & turbo) . BTW thanks for all your awesome info, THE BEST by far that I have seen .... 😁👍💪🙌
I have just purchased the ALDL cable and Tunerpro software from Envyous Customs and from what i have found out through PCMhacking i need to purchase a NVRAM first???? thats about all i know so far in regards to the Memcal based ECU tuning .... 😏
Depends on what the ecu is. Does it have pink and blue plugs or brown and tan ?
Im made a bench set up and am wanting to do a burble/pops an bangs tune any advice on what change using tuner pro ??
timing in the negatives where you are in over run
turn over run fuel cut off, or decel fuel cut off
@@RKGarage legend my bro just made a bench set up an bench tuned a burble on my vy your video was awesome an helped out heaps an do you know were would I get a bin file for lumpy idle tune churs bro ur a legend
I'm glad I could help.
At the moment I'm not releasing my lumpy idle tune as it makes the car a constant flamethrower and is no where near safe nor legal for road use.
@@RKGarage mad respect my bro keep up the solid work be keen if you ever do a lumpy tune that can be road legal im in nz so would have to check laws on that first
@RKGarage anyway you could make a video on this mate
Do u know whether i can use a elm327 as the aldl cable cheers
No mate, elm327 is for obd2
These are aldl
I’ve been trying to do this for ages and still haven’t got it right yet
Do you have a link can download page from please and If we Remove vats can we just gets the wires an ecu from a wreak flash it an throw in car an drive an keep stock ecu as spair
Sure can mate
Great video. would be great if you could post some of the mods which you may have done.
Havent done any mods man
Need help with a pop and bang tune on a vx v6 calais got a bench harness and aldl cable
All the negatives timing off throttle
All the fuels off throttle
RKGarage cheers man appreciate would love to talk more to get a better understanding
When doing this in the car do I need to get bin before write bin I'm confused and do I hit yes at the end or no when it says eeprom data In selected bin
Yes you need to get the bin beforehand.
@@RKGarage cause I watched ur other video and I don't see u getting the bin just the bin off enhanced
Yes you write the bin off enhanced.
No need to get the bin from your ecu beforehand
And do I hit yes when at end or no when it says do u want to program epprom from selected bin if unsure hit no there may be some issues
You need to hit yes
Plus thanks for the info legend
Any time!
What vehicle/vehicles does this ECU belong to?
It is literally in the title....
@@RKGarage Sorry not native to Australia hence the question. Is it a Holden Commodore by any chance
Can you put l67 fuel and ignition maps into my vy holden ecotec ecu I heard it carnt be just swapped over?
Nope different wiring harness plugs and ecu
But yeah I can do
@@RKGarage how much if I send ecu to you and you install supercharged bin onto the ecu? I'm in nz I'm turboing my vy
Oh in that case the supercharged bin is completely useless for you
You should make a video on how to make the cable
Isn't that what is in this video?
@RKGarage yeah I know I can do it in the car but not with my bench flashing harness not sure why I have done everything right I would rather do it on bench can you please help me out
I even bought a bench flashing harness for ebay for 250 not sure what that not working either
Watch the video. I legit explain it all on there.
Why that is not working ^^^
Hey mate what programs are you using on your computer
What for bud?
RKGarage to get the tune off the ecu cause I got tuner pro already
OSE Flash Tool
Can I have a picture of the sheet please
Pause and screenshot the video.
I can alao make and sell these as well
Yeah what PIN number is the accessories power I have the two orange and the red and black
I’ve tried everything and it’s still not working
@@RKGarage I’ve made mine but the program on my pc won’t open or detect it
Hey mate could you please send me a copy of that sheet to jayke Williams on face book Would be heaps appreciated
Have done man 👌
awesome