This is really cool idea. One thing I would do differently though, I would add a chain cover. If you throw a chain from a worn out link it might take some skin with it if the chain fliys off of the sprocket just right.
I have done those scooters back in the past 3 decades ago. You would have to change the sprocket ratio I believe right now your scooter won't move stand still you will have to push first to get it started especially with the clutch still on it. Also the clutch will burn out. The best way is to remove the clutch weld the lug nut on the motor shaft place the motor as closest possible to the tire with the lug nut firmly pressed against the tire weld motor in place and you're done.(you may have to fill up the tire with more air pressure) to start the motor you have to do is stand on the scooter with one foot with the other push yourself into the motor start and you'll keep driving you will hit about 20 to 25mph guaranteed
I really love how you showed us that motor all hooked up to nothing just vibrating and purring on the table. It's a raw obtainable cheap efficient power source. So many ideas. Could I power 4 wheels with 4 motors? Can you combine multiple motor powers like 3 motors to 1 wheel? Magical stuff man.
I have a near-identical engine in a powered earth auger (drills holes in the ground) and I agree with you: When it hits a rock, I reckon the kick from it could easily break your wrist of you weren't holding it the right way. I think that we all tend to forget just got powerful even small engines can be...
Wow...look at the expertise of armchair fabricators out there. I don’t know how they carry around the burden of so much wisdom 😂. Nice build - way to be resourceful with what you got 👍🏼
His home had refuse recycling. Hardly a young man of poverty and no means. But yeah, he uses his head. The scooter works and he inspired some kids that now want a stick welder, cutoff saw and drill press. You need the tools to build your dreams.
Hey love the vid!! Do you think with a different gear ratio, you could go faster? I was thinking you could even use a bike cassette with several gears and you could have a manual shifter
Yeah, i was thinking the same. I even think i want to try installing battery/starter/sound system/alternator/proper seat/roof/mini fan/etc etc hahahaha..
Hey man great job on using what you got and making a solid simple project I don't give a crap what people say on this you make do with what you got and you did and it looks good and functions.
Сразу видно что автор не вдавался в рассчёты, из-за этого самокат еле едит и движок только палит сцепление, а нормально разогнать никогда не получится. Проблема в слишком большой ведущей звезже, максимум она должна быть на 8 зубьев, но лучше 6. Сварка это отдельная тема и долго она не проживёт. Для того чтобы пластину на которой крепится двигатель не оторвало в первые минуты, нужно было приварить несколько расскосов.
A nice illustration of some mechanical principles - thank you. One of the more subtle issues is that more gearing is required because the centrifugal clutches are more of an on-off device, only fully engaging at over half the full rev range. This means that without the correct set of ratios they are always slipping or only work with downhill / gravity assistance, and a push start is absolutely needed. Am gonna have a go at a 3 or 5 speed rear internal geared hub 4 stroke engine version.
incredible project if I were I would replace the platinum with a used one and send it to a mechanical turner to machine a flange to fit the pinion for the chain pinion and crown ratio kit I would never cut but It was sensational amazing job
...ни фига себе!-, чё придумал!-, отличный получился мотосамокат!-, необходимо будет доделывать до ума:-ставить крылья над колёсами, кожух на цепь ну и конечно же покрасить!!!
Since this video covered needed aspects of the project, I'm not criticizing in any way ''at all'', but simply suggesting. I might've added a brace or braces to that vertical motor mount plate to help prevent your welds from cracking due to motor or bumpy road vibrations, however, since the frame was obviously heavy enough gauge steel that you could use a ''stick welder'', it may not matter. Instead of that plate, I may've welded another plate onto the frame to bolt the motor mount plate onto & added some slots to 1 of the plates so you could adjust the motor's position for whatever reason. Since you added that chain tension idler, the slots may not be needed to adjust your motor whichever way it ''might'' be needed . A very simple, yet excellent build. I've been wanting to build a 4-wheeled version of ''something'' powered with a weed-eater or chainsaw engine. I've torn apart chainsaws & know their drive setup, but since I haven't got around to tearing into 1 of these things yet, I wasn't sure what all was in 1 so this video was ''VERY BENEFICIAL'' in showing how simple the things are. GREAT JOB & GREAT VIDEO, SIR.
Arra azért kíváncsi lennék, hogy a kuplung szegmensdobban lévő 1 szem csapágy meddig bírná... mivel ezzel a megoldással nem egészen jó megoldás.. Idővel nem lesz központos.. és a kuplungpofák is idő előtt tönkremennek.. 🙄🤔
если не ошибаюсь, то при такой передаче и оборотах в среднем 4500 в минуту....скорость самоката будет около 60-70 км час или буксовать сцепление..поездишь недолго.. шестерня напрямую....значит средние обороты 4500 минимум... это в минуту.. умножим обороты на 60 минут в часе...разделим передаточное на 3, приблизительно... возьмем 10 дюймовое колесо где-то 0,75 метра на оборот... итого 4500*60=270000 затем делим на 3 =90000 умножаем на длину 0,75 и делим на тысячу =67,5 средняя скорость...ну как то не реально....точнее немыслимо...плюс подшипник быстро выйдет из строя
![I.N "HALLUCINATION" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/n5B5q1Hwt_U/mqdefault.jpg)
Dude that's awesome, on top of that, you're probably the only one who actually showed us what you were doing. Thanks :)
Zz
You used what you had and made something awesome, I respect it
This is really cool idea. One thing I would do differently though, I would add a chain cover. If you throw a chain from a worn out link it might take some skin with it if the chain fliys off of the sprocket just right.
Df
it builds character
I have done those scooters back in the past 3 decades ago. You would have to change the sprocket ratio I believe right now your scooter won't move stand still you will have to push first to get it started especially with the clutch still on it. Also the clutch will burn out.
The best way is to remove the clutch weld the lug nut on the motor shaft place the motor as closest possible to the tire with the lug nut firmly pressed against the tire weld motor in place and you're done.(you may have to fill up the tire with more air pressure) to start the motor you have to do is stand on the scooter with one foot with the other push yourself into the motor start and you'll keep driving you will hit about 20 to 25mph guaranteed
hello. interesting video well done, but please tell me why the star that is attached to the gearbox? Thanks.
thanks man I needed this gave me some thoughts about my 3 wheel trike
He can he. Ja. Be cue. Know. Byword. Cush yo he bugs. Ions. Bhsojs. He I x
I really love how you showed us that motor all hooked up to nothing just vibrating and purring on the table. It's a raw obtainable cheap efficient power source. So many ideas.
Could I power 4 wheels with 4 motors? Can you combine multiple motor powers like 3 motors to 1 wheel? Magical stuff man.
Shut up guys
Nvm
Hanya hanyah hshshc
T-)sk
Oo
Welding over paint, a true DIY'er
I like this scooter great job. I'd only recommend a chain guard. Hope you are still enjoying it after about a year!
62cc string trimmer? Wow, that’s “Shaking hands with danger”..... I love it
I have a near-identical engine in a powered earth auger (drills holes in the ground) and I agree with you: When it hits a rock, I reckon the kick from it could easily break your wrist of you weren't holding it the right way. I think that we all tend to forget just got powerful even small engines can be...
What Kindve speed you get?
My kll see
There are scooters with smaller engines 💀💀
The burnout was the next finishing touch, awesome
Kopp kopp kopp kip i9 on o ok pop ok ok
No, it was just ridiculous.
Aeosome 😀😃 good luck
Классная идея! Советую сделать Защиты на случай разрыва цепи.
paint over rust?! 💀
Bad news
Rust is lighter than carbon
Would it go faster with a smaller sprocket on the wheel or would it be more strain on the motor and end up going slower?
A smaller sprocket on the wheel would result in less torque but could spin faster
Wow...look at the expertise of armchair fabricators out there. I don’t know how they carry around the burden of so much wisdom 😂. Nice build - way to be resourceful with what you got 👍🏼
Thank you ❤️😂
🤔🤓🤓🤓🤓🤓👊
His home had refuse recycling. Hardly a young man of poverty and no means.
But yeah, he uses his head. The scooter works and he inspired some kids that now want a stick welder, cutoff saw and drill press. You need the tools to build your dreams.
Next project honda ivtec and turbo?
Mr IMBUS How fast?
Can you tell me where you got the motor mounts? I purchase one of these motors, but it didn’t have a mount included
Nice build ! 👍
Маленькая скорость.А ещё сиденье надо, а вообщем неплохо.А главное своими руками, а не куплено в магазине. И ведь это радует!
What kind of weight limit could that engine move? Asking for a...friend...who certainly exists and is not me
Nice ... Joint silencer ..
Love from India
Did u build the scooter chassis or did u buy it. Plz respond
i built it, also i will build second version of this scooter with better gear ratio and frame next week. Make sure you check it out! :)
Great thanks so much!
Hey love the vid!! Do you think with a different gear ratio, you could go faster? I was thinking you could even use a bike cassette with several gears and you could have a manual shifter
Yeah, i was thinking the same. I even think i want to try installing battery/starter/sound system/alternator/proper seat/roof/mini fan/etc etc hahahaha..
Hey man great job on using what you got and making a solid simple project I don't give a crap what people say on this you make do with what you got and you did and it looks good and functions.
Good work but as they have mentioned you have to put smaller sproket8 to avoid clutch slipping and wear
You need to put a smaller sprocket on engine to allow it to rev higher. That should be going a lot faster for a 62cc engine
Сразу видно что автор не вдавался в рассчёты, из-за этого самокат еле едит и движок только палит сцепление, а нормально разогнать никогда не получится. Проблема в слишком большой ведущей звезже, максимум она должна быть на 8 зубьев, но лучше 6. Сварка это отдельная тема и долго она не проживёт. Для того чтобы пластину на которой крепится двигатель не оторвало в первые минуты, нужно было приварить несколько расскосов.
@@TomRaily d
@@TomRaily no. Th-2uv
Hes probably got it geared down
@@luismartinez4081
😍❤
"...CROCKS! HE'S WEARING CROCKS! YOU'RE DRIVING THIS SMOKE HOUSE AROUND ON A SCOOTER... WITH CROCKS???"
From SNL sinkhole skit.
Smaller sprocket on the engine required, this is just riding/slipping the clutch all the time.
Na it just has very short hearing the back sprocket needs to be smaller
needs smaller front sprocket OR larger rear sprocket !
Hopeless gearing ratio !!anyone that has done this are laughing 😂
This is a great quick and easy diy project for me and my 8yo boy this spring thanks a million and keep up the good work my brother god bless all
A
Can i have your parts list?
Bracket holding engine should have been designed to cover all the 4 screws
or on both sides
Where did you get the gear on the weedeater and what is the tooth count and chain pitch? Very cool
You can get one off a pocket quad or a mountinbike which has more gears you need the smslkest
@@eliseizlotar thanks for the info, time to surprise the grandkids! 😉😉👍
Thanks again
@@gregorypiercesr.794 no problem
Wow amazing love it
Хрошый самокат неодин ласик Радом нестоял 👍,акитайский самокат .
A nice illustration of some mechanical principles - thank you. One of the more subtle issues is that more gearing is required because the centrifugal clutches are more of an on-off device, only fully engaging at over half the full rev range. This means that without the correct set of ratios they are always slipping or only work with downhill / gravity assistance, and a push start is absolutely needed.
Am gonna have a go at a 3 or 5 speed rear internal geared hub 4 stroke engine version.
I love it. Thanks
Why you weld with our removing the paint tho 🤦🏻♂️
6011 can burn it off 🤘👍😎
@@briantruck2284 or 6010
@@briantruck2284 thx inform
Amazingly clever 👍🏻
it's a nice project, can you share the scooter dimensions, good work
Maybe late to the party but beautiful work 👌
incredible project if I were I would replace the platinum with a used one and send it to a mechanical turner to machine a flange to fit the pinion for the chain pinion and crown ratio kit I would never cut but It was sensational amazing job
Thank you!
mother of invention, love when a great idea comes together god bless
I love the brake stand burn out!
Happy to subscribe.❤
Nice machine
😋👍👍👍
Very cool
Nice project 👍
Esse motor consegue fazer uma viagem de 200 km?? Colocando numa bike?
Yes
Quantos dentes tem a coroa e o pinhão,ficou bom de arrancada?
Hello, have a question is it needed to put the engine a bit up or we can put it on the frame close to the wheel?
Exelent video brother
Need to put a roller on to keep the chain tension but solid first little diy build
hello! cool idea! Can you tell me how to put a gearbox on a bike? Thanks.
I THINK you dont need a high torque gearing for this since the wheel is too small its already high torque its why its too slow.
what direction does your engine rotate when viewed from the clutch side when running? clockwise or anti clockswise.
Counter-clockwise
I wonder if this motor will work on a wheel chair
really cool. how did you build the back wheel? i wonder how to put a gear on mine.
...ни фига себе!-, чё придумал!-, отличный получился мотосамокат!-, необходимо будет доделывать до ума:-ставить крылья над колёсами, кожух на цепь ну и конечно же покрасить!!!
Better be careful at wide open throttle !! you might break speeds of 5 mph and that could extremely dangerous 😁
I have taken inspiration to this design and made it an L bracket that screws in just like yours does.
Great proyect, one question, wich Is that motor?? How can buy one thanks!
49cc strimmer motor
Рама хлипкая, развалится на первой кочке. Передаточное отношение слишком мало. Нужно хотя бы 9 к 1 (900 об мотора =100 об колеса). Сцепа буксует
Great! :-) How many teeth on sprockets?
13 and 40
ผมเคยทำครับ บิดไม่ขึ้น ครัชก็เปลี่ยนใหม่ แต่ผมเอาถ้วยครัช อันอื่นมาใส่ เกี่ยวกันไหมครับ
Since this video covered needed aspects of the project, I'm not criticizing in any way ''at all'', but simply suggesting. I might've added a brace or braces to that vertical motor mount plate to help prevent your welds from cracking due to motor or bumpy road vibrations, however, since the frame was obviously heavy enough gauge steel that you could use a ''stick welder'', it may not matter. Instead of that plate, I may've welded another plate onto the frame to bolt the motor mount plate onto & added some slots to 1 of the plates so you could adjust the motor's position for whatever reason. Since you added that chain tension idler, the slots may not be needed to adjust your motor whichever way it ''might'' be needed . A very simple, yet excellent build. I've been wanting to build a 4-wheeled version of ''something'' powered with a weed-eater or chainsaw engine. I've torn apart chainsaws & know their drive setup, but since I haven't got around to tearing into 1 of these things yet, I wasn't sure what all was in 1 so this video was ''VERY BENEFICIAL'' in showing how simple the things are. GREAT JOB & GREAT VIDEO, SIR.
ЗАПУЛА
how many cc is that engine sir..?
Its 62cc
It literally says it on the motor
Зажёг резину!Крутяк!
Hey what's the top speed on this awesome build
❤WOW❤❤❤❤❤❤
How fast will it go and how big is the motir
Здравствуйте поставил Вам лайк, подскажите как называется часть которую вы от пилили от двигателя?
❤super❤❤❤❤❤❤
Whelp, know Ik what to do with my old weed Wacker. Turn it to an epic go-kart/motor bike
I won't go very fast so I suggest selling it to make money for a pred engine
А как после сварки звездочку менять?.
А зачем её менять? Вообще, можно специальный редуктор потом заказать и все
@@Mitch196 Звездочка быстрее редуктора вый дет со строя.А менять все?Не экономно.
very good !! I also made one with a 150cc engine
Cool man but wath is the topspeed of it i am making my self one 2
❤Good❤❤❤❤❤❤❤
From where did u buy the motor???
Сцепление сразу развалилось? Вал то на одном подшипнике
Any ideas on how to trick out my powerchair i have a 1450d jazzy ??
I meed some ideas since im always in it.
Predator 670cc v-twin! 😂😂😂
Andrew Savage 😂💀
@@andrewsavage1872 dobladora de ángulo
Will you please include links to Amazon for the back wheel
now to put a 1gallon tank and drive it till empty for sport can always pick up a gallon on the other side to drive back
Very smart and clear video!!! Does that kind of engine have a centrifugal clutch? (It seemed to me) thank you!!!
its a commercial strimmer engine they all have that clutch bud
Super,cool.
What type of rear tire did he use and what type of brakes did he use
Arra azért kíváncsi lennék, hogy a kuplung szegmensdobban lévő 1 szem csapágy meddig bírná... mivel ezzel a megoldással nem egészen jó megoldás..
Idővel nem lesz központos.. és a kuplungpofák is idő előtt tönkremennek.. 🙄🤔
Это сцепление где звёздочка приварена не расчитано на боковое давление цепи, долго не прослужит. Но лайк за труд
👍🤝
Красавчик! Молодец!
I assume you would stall if you Dont keep the rear wheel off the ground at a stop?
O
L
Make more of stiff like this and post it for us please I see alot of cool things now like and ypu know what your doing obviously
если не ошибаюсь, то при такой передаче и оборотах в среднем 4500 в минуту....скорость самоката будет около 60-70 км час или буксовать сцепление..поездишь недолго.. шестерня напрямую....значит средние обороты 4500 минимум... это в минуту.. умножим обороты на 60 минут в часе...разделим передаточное на 3, приблизительно... возьмем 10 дюймовое колесо где-то 0,75 метра на оборот... итого 4500*60=270000 затем делим на 3 =90000 умножаем на длину 0,75 и делим на тысячу =67,5 средняя скорость...ну как то не реально....точнее немыслимо...плюс подшипник быстро выйдет из строя
Awesome!! If I could add one thing as a scooter designer? I'd mount the all 4 bolts to the engine. It'll last a lot longer .
what do i watch at 1 am:
Well I guess imma make a crazy looking skate board
Where did you get the rear sprocket on the wheel ?
Valeu
Thank you for the idea, will be doing something similar soon 👍🏼
All the blurry close ups just seems like the video creator was hiding something. My question is then why put up the video?
What is the maximum speed? 20 km/h or less?
Super 👍👏❤️🇵🇱
Nice build bro