Bravo majstore, bravo doktore!!! Još samo da ga ofarbaš u boji plamena vatre koja se prekida na pola rama!!! I mesto gde stavljaš noge mora biti još napred kao kod pravih čopera!!!
Wow, this is great. It's very beautiful. It's a self-made motorcycle. It's creative. When people don't have cars, we can drive this car ourselves.😊❤❤👍👍👍👍👍
You use this machine, right? This machine is a 50 cc grass cutter. You must mix 2 coats of oil, also known as auto-loop or engine oil for 2-stroke machines. This machine is a 2-stroke engine.😊
I think the gearing is messed up. The driver looks OK. But it should go directly to the rear wheel with 40+ tooth sprocket. I can't fathom right now, how the large crank sprocket to another large sprocket at the rear works. I guess the engine is cranking the cranks to crank the wheel.
Nice job but If the 2 front sprockets were switched, I suspect it would be much faster. It would greatly lower the gear ratio allowing the clutch to hook up and engine to rapidly gain rpm with ease. As it is, the clutch will burn up fast trying to lock up the clutch drum. That can't happen because your gearing is way too high.
Nice looking build,and a great idea.A bigger sprocket to take the power from the clutch will allow it to grab and increase torque./Lijepa konstrukcija i sjajna ideja. Veći lančanik za preuzimanje snage od kvačila omogućit će mu grabljenje i povećanje okretnog momenta.
Since you show us such chad moves as to hand-center two sprockets and weld them, it doesn't shock me any less that you didn't just weld the big sprocket on the wheel and put a smaller one on the crank so the gearing would be closer to right the first time. this gearing eats almost all the power this poor weed-wacker can produce boi.
All y’all saying slow, just put a 150cc, it’s not the actually usability it’s just a chopper with a trimmer engine. Ofc it’s gonna be slow what did you expect, past 200 miles per hour?
@@crossstation9359 я самодельный питбайк сделал. сварил раму и поставил туда веломотор F80, а также хороший карб докупил. прёт 60, тяга дичайшая, меня в любые горки затаскивает. Хоть он и выглядит гораздо хуже чем делают на заводах, НО я его сделал сам, и по характеристикам он сильно превосходит этот аппарат.
Я делал такую конструкцию. Но для этого у вас справа вместо педали должна быть очень маленькая звезда, около 11 зубов. А автор этого видео всё испортил, поставив большую звезду справа.
Pozdrav doktore! Koji je omjer okretaja motora i zupčanika na novom kvačilu? Radim sebi sličnu pa me zanima kakav je prijenos prije nego kupim to kvačilo. 😀
I'd made one with the same bike but I put in it A four stroke engine the engine cost $250 dollar and plus the tank lights banana seat high back Pole it runs 32 miles per hour I even had cops stop me to take pictures on it
Doctor, can you build please 160cc engine motorized bicycle, but not so wide as the old one, i can help you with model drawings. Sorry for my language, i am foreigner.
Upgrade that engine on the chopper bicycle to something much better like a small dirt bike or go kart engine but think 🤔 dirt bike engine would look sharp onto it doctor d.s. I've do the same thing I had a miniature go kart I've converted with huge wheels on the big of it and medium in the front had a 13 hp engine onto it as well and I sold it to someone a while back ago and planning on a new build soon later I'm just thinking 🤔 about it now and looking for something cheap to start off with
Com todos os meios que vc utiliza e o que gastou nesse projeto, vc pode ir à loja e comprar uma mobylette prontinha, motor de roçadeira não é compatível para tração.
Sve ok... jedino.... mogel si stavit " Banana sic" i sprovest neki auspuh da ne dimi po trenirki 😁... Dobio bi vise na izgledu ... Realno ova masinica je preslaba za bilo kaj.... al ok... slozeno je dobro ... 😉
This is cool for all boys and men between 0-100yrs.
Nah 0to170
Dudes everywhere saying hell yea to this one... I'm dudes
Bots
If you're 80 lbs bunk
AMAZING.. I WAS EXPECTING SOME LIKE THIS... THANKS DOCTOR🙋🇨🇴💚
Čestitamo učitelju! Hvala na ovom savjetu. No ja bih stavio oslonac za noge ispred motora, da noge budu ravnije.
Edit. (Here in 🇧🇷.)
Croation choppers😀🙃👨🏭
hehe Yeahh 👌👌
@@DShomemade imam prijedlog za neki od tvojih sljedeći videozapisa mozes li kupitimstari i neispravni Fiat 126 p i napraviti film restauraciju
Sve pohvale🏅✌️✌️✌️✌️
Okey pohvale
That's great guys in comments doesn't understand that engine power ISN'T speed, speed is in transmission, so you should put smaller cogwheel.
Bravo majstore, bravo doktore!!! Još samo da ga ofarbaš u boji plamena vatre koja se prekida na pola rama!!! I mesto gde stavljaš noge mora biti još napred kao kod pravih čopera!!!
Really really cool 😎🤩👍
Svaka čast super napravljeno vozilo.
No breaks haha, very cool!
Wow, this is great. It's very beautiful. It's a self-made motorcycle. It's creative. When people don't have cars, we can drive this car ourselves.😊❤❤👍👍👍👍👍
You use this machine, right? This machine is a 50 cc grass cutter. You must mix 2 coats of oil, also known as auto-loop or engine oil for 2-stroke machines. This machine is a 2-stroke engine.😊
Wouldve been quicker if you skipped the engine and left the pedals on
I think the gearing is messed up. The driver looks OK. But it should go directly to the rear wheel with 40+ tooth sprocket.
I can't fathom right now, how the large crank sprocket to another large sprocket at the rear works. I guess the engine is cranking the cranks to crank the wheel.
Nice job but If the 2 front sprockets were switched, I suspect it would be much faster. It would greatly lower the gear ratio allowing the clutch to hook up and engine to rapidly gain rpm with ease. As it is, the clutch will burn up fast trying to lock up the clutch drum. That can't happen because your gearing is way too high.
Very good idea 👍💡
Great video thanks, the bike is beautifully done.👍
I admire you work 😮
Wonderful job
Nice looking build,and a great idea.A bigger sprocket to take the power from the clutch will allow it to grab and increase torque./Lijepa konstrukcija i sjajna ideja. Veći lančanik za preuzimanje snage od kvačila omogućit će mu grabljenje i povećanje okretnog momenta.
good job ! bravo
Good job!
So good ii boss 👍👍😊😍
Nice work, can you show us this bike how it runs up hill?
It doesn't.
Para.mi ese motor no tiene empujé no es para subidas
Great project man, Love how it turned out, Just put some chain gourds pls😅😅
Việc làm của anh tuyệt vời 🤩
Good job but you should put mud protectors and a cover for the rotating chain and I repeat very good
Great skill amazing bike motor 👍
Good job 👍
Since you show us such chad moves as to hand-center two sprockets and weld them, it doesn't shock me any less that you didn't just weld the big sprocket on the wheel and put a smaller one on the crank so the gearing would be closer to right the first time.
this gearing eats almost all the power this poor weed-wacker can produce boi.
Parabéns cara, ficou muito foda essa bike motorizada. 👏
It's not the best thing, but it provides fuel and physical energy..😃
Nice job 👍
Koliko košta jedan ležaj u kučištu?
Svaka čast za najbolji kontent🙂🥇💪🏻
Zavisi ali oko 50kn - 7e
@@DShomemade Hvala na odgovoru🙂
I love this idea ❤️✌🏼🇭🇳
Need to rummage in junkyard by you 😂
I would recommend a muffler on it, so the gasses won't be directly in your way! 👍
Great bike, looks great, maybe add some apehangers 👍
Did we weld this plate directly next to a fuel tank with petrol inside. yes we did.
I was thinking the same!
BRAVO LARTISTE...BONJOUR DE LA FRANCE
That is fire my gang
the machine turned out to be slow but strong. I think that she will easily master the long climb of the road.
i need that thing in my life
It might make it faster if you switch the rear wheel gear sprocket for the one in front. It should give you more torque
All y’all saying slow, just put a 150cc, it’s not the actually usability it’s just a chopper with a trimmer engine. Ofc it’s gonna be slow what did you expect, past 200 miles per hour?
How do you already have sprocket in the grass trimmer?
I have the same chopper but with a 2 stroke, goes 21 mph. Not sure how you made it run so slow but yea.. I could walk faster than that
What engine kit u useing and also do u have disc brakes cause I have similar bike that I want to do this to but have heard u need disc brakes
the one in the video is a 2 stroke too
Why not build a mountain bike transmission from the engine to the transmission to the rear wheels?
This bike will definitely get you laid😂😂😂
❤❤🎉hkjkhhkj
quedo genial 💯
Why accelerator on the left?
hi from Russia! Guy, i think this motor so weaknes for this bike. I think BT80 or BT100 kit be better
не мотор чахлый, передаточное слишком маленькое.
@@Mr_Flybacker ну там либо на тягу делать, либо на скорость, но я не думаю что он больше 40 км/ч поедет
там передатку менять
@@HeavyyLux 25 если поедет на макс то и то много для него.. хонда дио чем не велик,50 едет за то
@@crossstation9359 я самодельный питбайк сделал. сварил раму и поставил туда веломотор F80, а также хороший карб докупил. прёт 60, тяга дичайшая, меня в любые горки затаскивает. Хоть он и выглядит гораздо хуже чем делают на заводах, НО я его сделал сам, и по характеристикам он сильно превосходит этот аппарат.
Super ,bravo
I built two about 20 years ago but they ran on top of the back wheel. The quicker one could do 55kmh/35mph flat out.
Does the frame feel strong enough?
Great video 🔥🔥🔥
how do you service the bearings from the original crank? And , The neighbors will Hate the noise.
Didn't the frame bend in any way after you removed the seat post fitting?
How many time for 0 - 100 km/h?😄
very good bike that i like so much
nice frame needs 100cc 4 stroke kit
dont understand why it was so slow . but hey tell people its a slow rider lol . be great for a kid . not fast still looks cool .
All that work for 5mph. Lol smh
Which bike use gear box
I wanna do something similar but with a 21 speed mountain bike That way I have the gear shifting capability So it's like I have a transmission
Я делал такую конструкцию. Но для этого у вас справа вместо педали должна быть очень маленькая звезда, около 11 зубов. А автор этого видео всё испортил, поставив большую звезду справа.
Pozdrav doktore!
Koji je omjer okretaja motora i zupčanika na novom kvačilu?
Radim sebi sličnu pa me zanima kakav je prijenos prije nego kupim to kvačilo. 😀
cool. 👍 was macht eigentlich der BMW- Pick up?
too slow, wrong gear ratio.
yes
The reduction is too high. The engine does not spin up.
That thing is slower than molasses going uphill in the middle of winter
So about how much do you have. Invested in that bike
I'd made one with the same bike but I put in it A four stroke engine the engine cost $250 dollar and plus the tank lights banana seat high back Pole it runs 32 miles per hour I even had cops stop me to take pictures on it
i don't know much about motorized bicycles, but where could i get one of unusable lawnmower sticks?
Please make a Electric one
Electric sucks
@@LyrikGriffeth Ah ok interesting
@@ddrusa well it's because of that I had an electric bike and the bike would always run out of battery in 10 minutes after a 45 minute charge
@@LyrikGriffeth Nah I seem the newer ebkes that have more power 150 750 watts
They even have a 1000 watt electric ebuke now
How much for assemble sir?
Painfully slow lol
Top 👍🏻👍🏻👍🏻😎
Essa Bike merece ter motor inscrito
8697
0:11
Funny.... you're a funnyman. - JAMES MAY
It's very good but it's noisy
That’s why it’s good
i need that clutch
Need to change the gear ratio
Só mais as Chopper's motorizadas aqui do Brasil 😅😅
awesome job ! improve the gearing to fully use the power of the engine ;)
Передаточное число слишком маленькое,на до где пидали поставить маленькую звезду а где колесо большую
This project might failed....its look too slow
Hoće li kad biti garage Tour .
God I wish I can do that to my bike but I only have the standard build
Doctor, can you build please 160cc engine motorized bicycle, but not so wide as the old one, i can help you with model drawings. Sorry for my language, i am foreigner.
I think the bicycle need more power
125cc dirtbike motor is better or electric 🤔
Napravi neki bicikl s prednjim i stražnjim pogonom
我想未來會有可能會把這種腳踏研發出來
Upgrade that engine on the chopper bicycle to something much better like a small dirt bike or go kart engine but think 🤔 dirt bike engine would look sharp onto it doctor d.s.
I've do the same thing I had a miniature go kart I've converted with huge wheels on the big of it and medium in the front had a 13 hp engine onto it as well and I sold it to someone a while back ago and planning on a new build soon later I'm just thinking 🤔 about it now and looking for something cheap to start off with
Попробуй из велосипеда сделать не мопед а просто чтобы было легко крутить это будет круто! С уважением
Dali bi prodo ja bih ga kupio 🍺🍺🍺
Pozz hahah taman novi motoric za tvog buraza
Koja je najvisa brzina s ovim
Com todos os meios que vc utiliza e o que gastou nesse projeto, vc pode ir à loja e comprar uma mobylette prontinha, motor de roçadeira não é compatível para tração.
Te quedó muy bonita la bicimoto
он орет больше чем едит. задумка неплохая, но слабоват движочек
Sve ok... jedino.... mogel si stavit " Banana sic" i sprovest neki auspuh da ne dimi po trenirki 😁... Dobio bi vise na izgledu ... Realno ova masinica je preslaba za bilo kaj.... al ok... slozeno je dobro ... 😉
Bros got everything lying around
fiz esse projeto , so que coloquei coroa extra na roda traseira, e montei o motor na garupa da bicicletas