A good advice! If you planning to use the same resin then just leave it in the printer and cover it with a big empty box 📦 from lights. You can leave out for years without during it back in the bottle. Of course only if the print didn't failed and big pieces can be inside
the last two old printers I covered the UV cover in paper and tape, at one point resin sat there for a few months no issues. Just needs a stir, Im planning on getting a nice cover sewn for it to pull over and still have a clear cover to film though for videos.
Hi Alan. Been a long time..., sorry! The new printer produces great details! Your designs look awesome!! Looking forward to your next video! Cheers, Tim
Life is a bit crazy for everybody atm and aware the bulk of my regulars enjoy binging my content once enough videos build up. Thank you for your long time support and kind feedback.
Wow, the outputs are so clean! Few years ago I was considering getting a used Anycubic to play with but not having a workshop space nor grasping the technical aspects of working with resin scared me off. Following with interest.
Resin printers are consumable and will break down after few hundred prints or worse few dozen bad print or mistakes. You can get a small one for around 100 something us and operate it on a balconie. Size of about an kitchen appliance plus smaller the easier to use
Hello, thanks for sharing all the details! I have a question: @5:50 you state ‘best detail is when resin is most viscous’. But then talk about keeping the resin warm. So is it better to have the resin cold and thick, or warm and thin?
Ah I go into much further detail in another video where I add a brewing heating band to the resin tank. Extra heat is better and some circumstances a must just to achieve bed adherence. ruclips.net/video/yG3D3o9gjCA/видео.html
Hey great video, Please don't take offence could you move/position the microphone slightly away from your month while recording since its giving out a bhoom every time you speak.
I currently own a mono 6K and took delivery of my 6KS last week and can honestly say it’s better in every regard. I am curious as to why you applied a screen protector when mine had one factory applied to the screen. Any cubic, moved away from an oversize protector with this printer, and is using one perfectly cut to fit the screen.
Except the UV cover I swapped it with the old yellow one. I assume being a late adapter of 6K mine is a different batch to yours. The screen protector was included separate and mentioned in the instructions to apply. I honstly do not see much of an advantage of it being perfect fit after using just cling rap on the older model. For after market application over sized would prevent user issues. Other wise very very happy with it.
Greetings, I was thinking of purchasing this Photon mono 6ks machine, and I would like to know if you have any problems during its use? Thanks. And great video
I got the table free from another art studio, it gets a spray and wipe but that decades of paint glue resin build up. No chemical on this earth sort of a sander will fix it.
@@mokanaman lol i understand that. so its become its own work of art with all that paint on it. Im currently waiting for my anycubic 6Ks to ship. cant wait to get it. Im moving up from the original mono with the 2k screen lol massive build volume on this new printer. Now I'm trying to find good resin that's not brittle but also has detail but wont cost too much. I know I'm hunting unicorns lol
@@mokanaman what kind of sunlu lol. Standard or abs like I've been eyeballing sunlu for a long time. Was hesitant when I first saw them but they've been around for a while now so they must be doing something right lol. Once these bottles of anycubic standard are gone im gonna give sunlu a try
I reviewed every resin I tried and gave feedback/ filmed the results (videos on this channel 3d printer play list). Used Sunlu standard flesh color and grey with great results and happen to be the cheapest in bulk. Found Anycubic to be the worse (still very usable) from my experience outside obscure local brands.
Im in Australia, we have a massive beer culture here and import brews are not uncommon. We also have a ton of ethic communities with specialty import grocery stores. You can find almost anything with 20km of my studio. This bottle is not mine and I have no idea who it belongs to or how it got there. Do recall drinking one and its alright.
@@mokanaman glad you tried it and liked it! Top brand in Colombia historically. Came for 3d printing tips and ended up spotting import brewery! Cheers!
No need to cover subjects twice, did a few lewd build and posted them in the figure and shorts play lists in detail. Only if that is your cup of tea, airbrush and tutorial play lists has videos on blending and shading flesh tones.
A good advice! If you planning to use the same resin then just leave it in the printer and cover it with a big empty box 📦 from lights. You can leave out for years without during it back in the bottle. Of course only if the print didn't failed and big pieces can be inside
the last two old printers I covered the UV cover in paper and tape, at one point resin sat there for a few months no issues. Just needs a stir, Im planning on getting a nice cover sewn for it to pull over and still have a clear cover to film though for videos.
Hi Friend! Isn't the smell of resin annoying when you leave it in the printer?
Hi Alan.
Been a long time..., sorry!
The new printer produces great details! Your designs look awesome!!
Looking forward to your next video!
Cheers, Tim
Life is a bit crazy for everybody atm and aware the bulk of my regulars enjoy binging my content once enough videos build up. Thank you for your long time support and kind feedback.
Wow, the outputs are so clean! Few years ago I was considering getting a used Anycubic to play with but not having a workshop space nor grasping the technical aspects of working with resin scared me off. Following with interest.
Resin printers are consumable and will break down after few hundred prints or worse few dozen bad print or mistakes. You can get a small one for around 100 something us and operate it on a balconie. Size of about an kitchen appliance plus smaller the easier to use
you've come such a long way, my g
Great video.
Love the G-13!
Hello, thanks for sharing all the details! I have a question: @5:50 you state ‘best detail is when resin is most viscous’. But then talk about keeping the resin warm. So is it better to have the resin cold and thick, or warm and thin?
Ah I go into much further detail in another video where I add a brewing heating band to the resin tank. Extra heat is better and some circumstances a must just to achieve bed adherence. ruclips.net/video/yG3D3o9gjCA/видео.html
Hey great video, Please don't take offence could you move/position the microphone slightly away from your month while recording since its giving out a bhoom every time you speak.
I currently own a mono 6K and took delivery of my 6KS last week and can honestly say it’s better in every regard. I am curious as to why you applied a screen protector when mine had one factory applied to the screen. Any cubic, moved away from an oversize protector with this printer, and is using one perfectly cut to fit the screen.
Except the UV cover I swapped it with the old yellow one. I assume being a late adapter of 6K mine is a different batch to yours. The screen protector was included separate and mentioned in the instructions to apply. I honstly do not see much of an advantage of it being perfect fit after using just cling rap on the older model. For after market application over sized would prevent user issues. Other wise very very happy with it.
I came for the printer but stayed for the accent.
Greetings, I was thinking of purchasing this Photon mono 6ks machine, and I would like to know if you have any problems during its use?
Thanks. And great video
Hello, its been flawless so far. Only 3 failed primes out of about 40 all of them my fault, I cannot see why I cant get a full life out of it.
Thanks my friend
great video and info but dude you need to wipe down the craft area. that scale the screen was so dirty I'm surprised we could see it. lol.
I got the table free from another art studio, it gets a spray and wipe but that decades of paint glue resin build up. No chemical on this earth sort of a sander will fix it.
@@mokanaman lol i understand that. so its become its own work of art with all that paint on it. Im currently waiting for my anycubic 6Ks to ship. cant wait to get it. Im moving up from the original mono with the 2k screen lol massive build volume on this new printer. Now I'm trying to find good resin that's not brittle but also has detail but wont cost too much. I know I'm hunting unicorns lol
buy a bottle of every resin you can find and keep testing, my settings produced the best results with sunlu and a heating band.
@@mokanaman what kind of sunlu lol. Standard or abs like I've been eyeballing sunlu for a long time. Was hesitant when I first saw them but they've been around for a while now so they must be doing something right lol. Once these bottles of anycubic standard are gone im gonna give sunlu a try
I reviewed every resin I tried and gave feedback/ filmed the results (videos on this channel 3d printer play list). Used Sunlu standard flesh color and grey with great results and happen to be the cheapest in bulk. Found Anycubic to be the worse (still very usable) from my experience outside obscure local brands.
So you are from Colombia or in Colombia, or you visited Colombia whatsoever but that beer bottle comes from there. How did it get to your hands ? 😅
Im in Australia, we have a massive beer culture here and import brews are not uncommon. We also have a ton of ethic communities with specialty import grocery stores. You can find almost anything with 20km of my studio. This bottle is not mine and I have no idea who it belongs to or how it got there. Do recall drinking one and its alright.
@@mokanaman glad you tried it and liked it! Top brand in Colombia historically. Came for 3d printing tips and ended up spotting import brewery! Cheers!
WiFi no WiFi?
Yes has wifi but cannot comment on it as I have not tested it and really dislike operating machines or feeding data like that.
Let’s just breeze past the hentai prints 😩
No need to cover subjects twice, did a few lewd build and posted them in the figure and shorts play lists in detail. Only if that is your cup of tea, airbrush and tutorial play lists has videos on blending and shading flesh tones.