Thank a lot for the video. I had take mine apart a few days before my rebuild kit came and I got my parts mixed up. Could not figure out what I had wrong the gun wouldn’t do anything. With this video I figured out what I had wrong saved me a trip to the shop.
This gives me confidence to tear apart this expensive gun. Thanks. My gun does not leak, but drives a nail and then locks as soon as I hook up the air without touching the trigger. Lot of parts in there and just going through the rebuild procedure might identify the real problem. Right now the gun is not usable at all.
7:46 wondering about the cap. Looks like an o-ring around that cap. Is there🤔? Sorry, have one other question. Does anything need to be torqued at all, or just hand tighten? I know you didn’t torque anything down, but wondering if should, or just doesn’t matter at all. Thx for vid, liked that did step by step for everything got in the kit
I watched this video because I had to replace a driver guide that I blew apart, assuming because I put it in backwards after a teardown. Does the round opening go up or down? The other side has a triangular opening.
I need item#13 for my Bostitch N64C because it broke, but can not find one anywhere. And there is not a rebuild kit so what o-rings and things would you recommend replacing? Same for my N57C I need some help locating parts too
MY pawl feed retainer pin fell out of my n80 nailer . I found the pin but can't find a retainer for the top when it's installed. The n46 roofing nailer uses the same style setup. Not sure if it's the same size. Can you recommend a solution.
Hi Aaron, I can't seem to find that model number on our website. I did find a parts list for this Nailer though: www.fix.com/models/nailer/bostitch/id783259/n63cp/
Hello, I have a problem. The nailer is identical to the one in the photo, the hammer does not retract all the way and therefore loads two nails. Does anyone know why the hammer does not retract all the way?
Thank a lot for the video. I had take mine apart a few days before my rebuild kit came and I got my parts mixed up. Could not figure out what I had wrong the gun wouldn’t do anything. With this video I figured out what I had wrong saved me a trip to the shop.
More of the same ,Excellent Tutorial!
Just enough without lag times.
Covered the subject perfectly.
Thanks 👍🏽👍🏽
This gives me confidence to tear apart this expensive gun. Thanks. My gun does not leak, but drives a nail and then locks as soon as I hook up the air without touching the trigger. Lot of parts in there and just going through the rebuild procedure might identify the real problem. Right now the gun is not usable at all.
You are so kind to show this to us. Thank you.
GREAT TUTORIAL. VERY SIMPLE APPROACH. GOOD PACE OF DEMONSTRATION.
What type of lubricant do you use? Does it come with the rebuild kit?
Excellent tutorial! Thank you so much! You are a blessing!
Great video. I might suggest using blue locktite instead of red because blue can be removed with force but red takes heat to break the bond.
the Locktite is blue, just the tube is red
7:46 wondering about the cap. Looks like an o-ring around that cap. Is there🤔?
Sorry, have one other question. Does anything need to be torqued at all, or just hand tighten? I know you didn’t torque anything down, but wondering if should, or just doesn’t matter at all.
Thx for vid, liked that did step by step for everything got in the kit
Did you replace the o-ring on the greenish cap?
Great video. Bravo 👏
My Bostitch finishing nailer is leaking air at the trigger. It has hardly been used and has been sitting in the case. What should I do?
This was amazing
I watched this video because I had to replace a driver guide that I blew apart, assuming because I put it in backwards after a teardown. Does the round opening go up or down? The other side has a triangular opening.
On last step. Washer "goes on third after magazine then safety cover.
Will this rebuild kit work for a n12
A rebuild is kinda short when you don't do anything for the wornout trigger valve assembly.
I need item#13 for my Bostitch N64C because it broke, but can not find one anywhere. And there is not a rebuild kit so what o-rings and things would you recommend replacing? Same for my N57C I need some help locating parts too
MY pawl feed retainer pin fell out of my n80 nailer . I found the pin but can't find a retainer for the top when it's installed. The n46 roofing nailer uses the same style setup. Not sure if it's the same size. Can you recommend a solution.
I have a Finish nailer N60FN and the problem is the piston never gets to rhe upper position
I am looking for a rebuild kit for N65CP Bostitch Nailer and the cylinder seal, but can't find it. Do you have access to it?
Hi Aaron, I can't seem to find that model number on our website. I did find a parts list for this Nailer though: www.fix.com/models/nailer/bostitch/id783259/n63cp/
Hello, I have a problem. The nailer is identical to the one in the photo, the hammer does not retract all the way and therefore loads two nails. Does anyone know why the hammer does not retract all the way?
Where can I but the rebuild kit for a bostitch nailer strap
Model MCN150?
Buy !!
how to repair the triger?
where can I buy just the bumper?
Thanks for the question. If you send us the model number of your Nailer, we might be able to find you the bumper you're looking for!
Add more ,air leakage trublshoot
IF POSSIBLE CAN YOU PRODUCE A VIDEO ON A PORTER CABEL " MODEL RN175C TYPE 1" ROOFING NAILER I,M GOING CRAZY HERE !! THANK YOU !! , PJP