building a table router with an affordable hand router [woodworking]

[@JoseSilveira-newhandleforYT]

Interesting project! I would love to see how you extended the table saw to continue use of the saw fence with the router - When you have the time, you could do a video of how it looks like from the sides we never see.

[@j-woodworking9573]

Thanks for watching sir.

[@차주영-c1x]

유용한 영상 감사합니다.
마지막 부분에 나오는 클램프 제품 정보 알 수 있을까요.

[@최병호-b9g]

마지막 크램프는 어디서 구매하나요

[@frankstover3444]

Brilliant job!

[@j-woodworking9573]

Thanks for watching sir.

[@bhaygood7306]

Thanks just wondering how long plywood hold up under 3 HP router pulling 2.5 to 3 inches bit all ready have 52 inches cut on table saw 👍👍👍

[@jeanloreaud9282]

Très joli travail bravo à bientôt salut Jeannot 🛠😉

[@j-woodworking9573]

Thanks for watching sir.

[@rolandgdean]

I need to do this in my saw so badly. Great job sir!

[@j-woodworking9573]

Thanks Roland.
I always think think highly of you.

[@rolandgdean]

@@j-woodworking9573 same.

[@paulstanding7267]

Very nicely done when I use a fluted bit I always take a bit out with the saw bench or put a straight bit in so not to get the flute blocked and cuts cleanly take care 😀

[@j-woodworking9573]

Thanks for your kind comment.

[@zizai82]

我发现棒子的木工就是螺丝，木工胶都不用的。还有这哥们电转重来没有垂直过。

[@wolfganghover6218]

Hello,
you do all Time a Great Job, thank you for this Video!
Greetings from Germany. 👍👌🤗

[@j-woodworking9573]

Nice to see you again.
Thanks for watching sir. Greetings from Korea.

[@jimpike3489]

Great idea, i will add one of these to my table saw bed. Thanks for sharing

[@j-woodworking9573]

Thanks for watching sir.

[@frankkamolov3815]

👍👍👍👏👏👏

[@NYWoodworker]

I am goning to do the same on my Bosch job site saw, however, how do you adjust bit height and change bits. With six screws holding the plate down, it is not very convenient.

[@Erik_The_Viking]

I was thinking the same thing - taking the screws out all the time would get old really fast.

[@206Seaman]

Would be a nuisance wouldn’t it? How about two threaded inserts in each support and countersunk holes in the top? Use short machine screws so just a few turns would lock it down. Leveling screws wouldn’t hurt either. That said, he thinks things through pretty good, then, like most of us, has to change a few things halfway through.

[@j-woodworking9573]

It isn't convenient but it is not so difficult.
To adjust the bits there are two ways. Rough and fine. With the router mounted we can push up the router to approximate hight and turn the knob on it to exact height.
To change bits, we can do that beneath the plate with the router mounted.
Yes, I think those are unconvenient too. If you want a perfect one, you can buy a table router made by manufacturers.
Thanks for watching sir.

[@鄭博聰]

非常厲害

[@j-woodworking9573]

Thanks for watching sir.

[@sapelesteve]

Nicely done J! However, as others have noted, how do you change bits? Removing 6 screws every time you want to change a bit would get rather tedious. Also, you better watch your fingers more closely. Making a cut in the middle of a board like you did & using your fingers to push the wood over the bit is NOT a real good idea. Just be safe........... 😉😉👍👍

[@kaasmeester5903]

The way this is set up, it looks like you can still reach under the table and get the wrench on the chuck to change out bits, without having to undo those 6 screws.

[@j-woodworking9573]

Thanks for your exact answer. I do that way.

[@j-woodworking9573]

Sorry I'll be careful.
Thanks for kind comment.

[@richardnash6009]

Excellent I like this fantastic thank you 🙏🙏🙏🙏

[@j-woodworking9573]

Thanks for watching sir.

[@eoboe5403]

Great!

[@SER-spb]

Спасибо!

[@j-woodworking9573]

Thanks for watching sir.

[@capatainnemo]

why didnt you use the router to cut the hole for the saw?

[@j-woodworking9573]

There are various ways.
Thanks for watching sir.

[@songhoje]

집진은 어떻게 하나요?

[@j-woodworking9573]

죄송합니다. 안타깝게도 집진문제는 해결하지 못했습니다. 하지만 루터작업은 테이블쏘작업량보다 비교적 적어 큰 불편함이 없습니다. 작업 중간중간에 집진시스템의 호스로 해결합니다.

[@songhoje]

@@j-woodworking9573 제걸 보여드리고 싶은데 보여줄 방법이 없네요.테이블 쏘에서 네가지가 가능한데 동영상에 올리지 않을 것이니까요.많이 연구해 보세요.답을 찾을 겁니다.

[@j-woodworking9573]

@@songhoje 감사합니다.

[@songhoje]

@@j-woodworking9573 제자들에게 님의 영상을 보여드렸습니다.참신하다고 하네요

[@j-woodworking9573]

@@songhoje 정말 부럽습니다. 지금이라도 체계적이지 못한 제 기술을 선생님같은 분들로부터 전수받고 싶은데 쉽지가 않습니다.
선생님의 가르침에 감사드립니다.

[@koccocarrasco5696]

👍🏻👍🏻👍🏻

[@kopusoff]

Не понял а зачем надо стол портить тоесть пилить

[@486yooil]

파워메틱스~~

[@j-woodworking9573]

감사합니다.

[@ЕвгенийГрищук-и1ч]

👍

[@j-woodworking9573]

Thanks for watching sir.