Thanks a lot for this video❤. I followed all the steps and it worked. But I faced an issue at beginning. I will elaborate in case someone else has this issue. My indoor unit is some 50ft away from the camera and lock. The adapter for powering the lock was also given at this distance and I used cat6 cable for this also. Initially I used 1 wire each from cat6 for giving + and - but it worked only sometimes. Reason being power loss. Then I gave 2 wires for each and it worked. So if anyone facing issue even after giving right connections, make sure this is looked after. Thanks.
we usually use 18/2 gauge cable for running door strike, so doubling up a twisted cat6 is highly recommended. When i see 1 wire for power for devices like camera, it will have many issues. always use 2 wires for power, so 4 wires total if you're doing for postive and negative
Thanks for the video. If I connect the door bell using 12v and not using poe, what connections do I need to connect to an electronic lock? Connect the blue and green wires together?
Thanks for the video, I have a question when connecting the electric strike. If the electric strike comes with open-close feed signal and I connect it to the "Door Contact AIN1" terminal, from where do I see if the door is locked or not? From the hikconnect app?
Hello! Can you help me? Are only 2 options to make internet connecton for the outdoor station? 1. it connects to the wifi router by wifi, 2. connects to the wifi router by wire. What if the outdoor station connect to the indoor station by cat5e cable, and the indoor station connect to the router by wifi? Won't it work?
Hello, I have a question: Why is power needed for a door lock if the Outdoor unit is connected via POE. I thought it would be UTP cable from Indoor unit to Outoor unit, and then from Outdoor unit to door lock via 2-wire cable? Thank you
Because the lock needs different voltage and more current that the POE can supply. The outdoor unit gives no power to the doorlock, it just gives a relay output to close or open the circuit.
Hello sir, in your video you connect the + from power adapter directly to lock opener, in KV6113 manual the + and - should go through the unit. Output + is via (BLUE - NO) and (GREEN - COM). If you connect like in your video + always connected there is no control for - COM. As the Blue NO is positive +. Is this a change in new models?
I have 11.5 volt 4 amp power supply in my traditional bell to unlock the door , Can I use it or should I use only the supplied power supply? I am gonna use poe to power outside unit.
In vdp DS-kV6113-WPE1 there is a terminal AIN1 and GRD, with 5v in open condition, to connect door sensor alarm, after connecting a reed swtich door sensor, where to configure alarm, whether alarm will display in Monitor DS-KH6320-WTE1 or in Hikiconnect phone. I have connected a magnetic reed contact on the terminal but no alarm aprears anywhere. Please help
This video helped me a lot, but it was for a 1 door and 1 room configuration. If there are many doors and many rooms. what to do? Multiple indoor stations and outdoor stations can be interconnected. How to do this?
Gracias por el video, si tengo un Switch PoE, este me puede alimentar también a la cerradura eléctrica desde el Frente de Calle o es necesario el adaptador de voltaje?
DS-KD8003IME1 NO NEED ADITIONAL ADAPTOR. THIS DEVICE WILL SHARE POWER TO LOCK. BUT OTHER DEVICE NEED ADITIONAL POWER ADAPTOR.DS-KD8003IME1 NO NECESITA ADAPTADOR ADICIONAL. ESTE DISPOSITIVO COMPARTIRÁ LA ENERGÍA PARA BLOQUEAR. PERO OTRO DISPOSITIVO NECESITA UN ADAPTADOR DE CORRIENTE ADICIONAL
@@adshikvision tengo conectados la pantalla por cable lan y adaptador 12v y el timbre con camara via inalambrica y adaptador 12v cuando le doy al boton para abrir la cerradura electrica no le entrega suficiente voltaje
How to setup a record on SD card? I couldn't play back videos from SD card. It shows no SD card message even though the card is installed and formatted
Is the micro SD card in the doorbell on the outside or is it not on the screen on the inside? I have a card in the doorbell and when someone rings there is no photo saved or a record of who rang the doorbell ???
Amazing video. I have a door knock that use 12V AC instead of DC, do you know if I can connect it? Or should I put some kind of relay in the middle? Thanks
Hola Gracias por el video, muy bien explicado, tengo una duda, puedo conectar el Video portero con la pantalla LCD sin necesidad del PoE o sea directamente con el cable UTP?
Hello, good evening, I purchased an Intercom kit (video intercom) from Hik Vision of the Model - DS-KV6113-WPE1(C), I have already programmed it completely but there is a situation missing that has to do with intrusion or movement detection. I have already inserted a micro SD card and still the device does not recognize it or says that there is no card inserted. Because my goal is when the doorbell detects movement I get notified and I save an excerpt of that moment. If you need to send some prints to show something, say so. Waiting for reply Thank you,
I didn’t run a cable from the outdoor intercom to the door lock, instead I ran a cable from the indoor intercom to the door lock. Is the wiring still the same?
Wiring can be from indoor relay station to lock, change display to unhide the indoor relay you connect. That aperars as another lock in display. Use the same to inlock. I did it. If outdoor is far away this a solution .
Hello I have a DS KV8x13-M device. Is it possible to connect a small gate with magnetic lock + a double gate opener for a car to this device and how? :]]
hello. I could see visitors' photo in the app while using this device. I reinstalled for the new monitor, but now I can only see visitors as alerts. How do I set it up so I can see visitor photos?
Hi, I don't unbderstand how this is not a security risk. If you want to break into house you basicli need to just couple together two wires and thats it, the door opens for you. mabey I am missing something but I feel that the door opening rele should be on inside unit.
I m facing an error. Once someone ring the bell from outside nd it worked properly but if the person ring it again it didn’t showed up. It required few minutes then jt worked
Hola buenas tardes, a mí lo que me gustaría saber, es a donde está conectado el frente de calle, y el monitor, ya que los dos tienen distintos cables tipo utp
If I have already in place a KIS-203 device connected on 4 wires, can I replace it with KIS-602 without POE? Which will be the wires that I have to use?
Hola. Perfecta explicación. Tengo éste equipo, pero en mi caso quiero conectar el frente a un portón para realizar la apertura automática. Sería ésto posible? Gracias!
this is a realy lame desing... i just snap the plastik button case and conect two wires and open the door from outside... thanks for the video i almoust bought it...
In vdp DS-kV6113-WPE1 there is a terminal AIN1 and GRD, with 5v in open condition, to connect door sensor alarm, after connecting a reed swtich door sensor, where to configure alarm, whether alarm will display in Monitor DS-KH6320-WTE1 or in Hikiconnect phone. I have connected a magnetic reed contact on the terminal but no alarm aprears anywhere. Please help
After connecting a door contact sensor to DS-KV6113-WPE1(C) for alarm, where do we get alarm? There is a provision on DS-KH6320-WTE1 display station and it works giving alarm. But usually door contact wiring is near to door and vedio phone, again multiple outdoor station requires door contact to be connected to phone station as only one door contact alarm can be configured in display
Это самая доходчивая и понятная схема ОГРОМНОЕ СПАСИБО автору
большое тебе спасибо
Единственная адекватная инструкция на эту панель во всем ютубе рахмет автору
Thanks a lot for this video❤. I followed all the steps and it worked. But I faced an issue at beginning. I will elaborate in case someone else has this issue.
My indoor unit is some 50ft away from the camera and lock. The adapter for powering the lock was also given at this distance and I used cat6 cable for this also. Initially I used 1 wire each from cat6 for giving + and - but it worked only sometimes. Reason being power loss. Then I gave 2 wires for each and it worked. So if anyone facing issue even after giving right connections, make sure this is looked after. Thanks.
we usually use 18/2 gauge cable for running door strike, so doubling up a twisted cat6 is highly recommended. When i see 1 wire for power for devices like camera, it will have many issues. always use 2 wires for power, so 4 wires total if you're doing for postive and negative
Do you have an easy way to connext the small cables from the door bell to the lock?
Thank you
Thanks for the video. If I connect the door bell using 12v and not using poe, what connections do I need to connect to an electronic lock? Connect the blue and green wires together?
Yes
Is that possible? Can connect the door lock with out poe?
Does an additional 12V adapter for the lock need to be used if the external bell is connected to 12V without PoE?
Yes
Thanks for the video, I have a question when connecting the electric strike. If the electric strike comes with open-close feed signal and I connect it to the "Door Contact AIN1" terminal, from where do I see if the door is locked or not? From the hikconnect app?
Yes it will
@@adshikvision thank you sir.
Hello! Can you help me?
Are only 2 options to make internet connecton for the outdoor station?
1. it connects to the wifi router by wifi, 2. connects to the wifi router by wire.
What if the outdoor station connect to the indoor station by cat5e cable, and the indoor station connect to the router by wifi? Won't it work?
Hello, I have a question: Why is power needed for a door lock if the Outdoor unit is connected via POE. I thought it would be UTP cable from Indoor unit to Outoor unit, and then from Outdoor unit to door lock via 2-wire cable? Thank you
Because the lock needs different voltage and more current that the POE can supply. The outdoor unit gives no power to the doorlock, it just gives a relay output to close or open the circuit.
The maglock doesn't support, Poe. It supports your traditional power. 12v 2.amp . That's why a separate power was used
Hello sir, in your video you connect the + from power adapter directly to lock opener, in KV6113 manual the + and - should go through the unit. Output + is via (BLUE - NO) and (GREEN - COM).
If you connect like in your video + always connected there is no control for - COM. As the Blue NO is positive +. Is this a change in new models?
Yes, correct
I have 11.5 volt 4 amp power supply in my traditional bell to unlock the door , Can I use it or should I use only the supplied power supply? I am gonna use poe to power outside unit.
use ur dedicated pwr supply for lock
Gracias por el video.Una consulta en un video portero analogo de 4 hilos que cable uso para conectar la pantalla a una distancia mayor a 30 metros?
usar cable de alarma
You didn’t power doorbell camera how its running? You just connet adapter for lock answer please?
door bell connected to POE switch, it will get power from POE switch
Do you configurit without PC
My is 15 metres but can't connect well, when you call it ends before it rings on screen. Please help me.
In vdp DS-kV6113-WPE1 there is a terminal AIN1 and GRD, with 5v in open condition, to connect door sensor alarm, after connecting a reed swtich door sensor, where to configure alarm, whether alarm will display in Monitor DS-KH6320-WTE1 or in Hikiconnect phone. I have connected a magnetic reed contact on the terminal but no alarm aprears anywhere. Please help
Hi. Which of the Hikvision IP video intercom sets can provide power supply to door lock also? Thanks.
use DS-KD8003IME1
@@adshikvision Thanks. I think this is part of DS-KIS602 set. Does DS-KIS607-S have this functionality too?
This video helped me a lot, but it was for a 1 door and 1 room configuration. If there are many doors and many rooms. what to do? Multiple indoor stations and outdoor stations can be interconnected. How to do this?
i posted other video for multiple doors
you can check
Thank you for the awsome video!!! Super helpful
You're so welcome!
Gracias por el video, si tengo un Switch PoE, este me puede alimentar también a la cerradura eléctrica desde el Frente de Calle o es necesario el adaptador de voltaje?
No, vas a requerir voltaje para la cerradura por separado.
DS-KD8003IME1 NO NEED ADITIONAL ADAPTOR. THIS DEVICE WILL SHARE POWER TO LOCK. BUT OTHER DEVICE NEED ADITIONAL POWER ADAPTOR.DS-KD8003IME1 NO NECESITA ADAPTADOR ADICIONAL. ESTE DISPOSITIVO COMPARTIRÁ LA ENERGÍA PARA BLOQUEAR. PERO OTRO DISPOSITIVO NECESITA UN ADAPTADOR DE CORRIENTE ADICIONAL
@@adshikvision tengo conectados la pantalla por cable lan y adaptador 12v y el timbre con camara via inalambrica y adaptador 12v cuando le doy al boton para abrir la cerradura electrica no le entrega suficiente voltaje
How to setup a record on SD card? I couldn't play back videos from SD card. It shows no SD card message even though the card is installed and formatted
if u install SD card on Display unit, it will capture the photos only not video. If any missed call it will captur photo
Is the micro SD card in the doorbell on the outside or is it not on the screen on the inside? I have a card in the doorbell and when someone rings there is no photo saved or a record of who rang the doorbell
???
@M.Shlowi Does your device take a photo of who rang the doorbell?
Very useful video. Thank you for that, however I have additional question. Is it possible to connect to this kit additional thing - gate for cars?
Yes, absolutely
Thank you... Can you advise how to connect to DS-K4T100-Electric-Bolt please? also how to configure the Mayfair cards to open the door?
same steps you follow.
ruclips.net/video/exm1sf187sk/видео.html&ab_channel=ADSHikvisionTech
Amazing video. I have a door knock that use 12V AC instead of DC, do you know if I can connect it? Or should I put some kind of relay in the middle? Thanks
use with Relay
Hola Gracias por el video, muy bien explicado, tengo una duda, puedo conectar el Video portero con la pantalla LCD sin necesidad del PoE o sea directamente con el cable UTP?
SÍ, PERO NECESITA UTILIZAR UN ADAPTADOR DE CORRIENTE DE 12V
@@adshikvision hola como serian las conexiones en caso de solo utilizar los adaptadores de corriente de 12v?
Hello, good evening, I purchased an Intercom kit (video intercom) from Hik Vision
of the Model - DS-KV6113-WPE1(C), I have already programmed it completely but there is a situation missing that has to do with intrusion or movement detection.
I have already inserted a micro SD card and still the device does not recognize it or says that there is no card inserted.
Because my goal is when the doorbell detects movement I get notified and I save an excerpt of that moment.
If you need to send some prints to show something, say so.
Waiting for reply Thank you,
Can we give adopter power supply instead of Poe for both the device and use wifi ????
yes
I didn’t run a cable from the outdoor intercom to the door lock, instead I ran a cable from the indoor intercom to the door lock. Is the wiring still the same?
Run cable from Outdoor to lock
Wiring can be from indoor relay station to lock, change display to unhide the indoor relay you connect. That aperars as another lock in display. Use the same to inlock. I did it. If outdoor is far away this a solution
.
Can I use this model to open Barier/Turnstile?
Yes you can
@@adshikvision thank you
Buen dia amigo que tipo de boton o marca utilizaste?
puedes usar cualquier tipo de botón de salida
disponible en el mercado
puedo utilizar el zkteco que le puedo condigurar controles inalambricos para abrir por fuera sin tarjeta?@@adshikvision
It's just me thinking that someone could break the outside unit and manually connect / disconnect the door lock relay cables to gain access ?
yes
you can use secure module for more safty
El video es muy bueno, lo unico que le falto fue hablar y habria sido genial ir explicando poco el paso a paso
i have poor voice dear
j'ai une mauvaise voix ma chérie
And can you please tell me how to connect alarm in this? Doorbell?
you can use AIN1 and AIN2 for alarm
Et si on veut connecter la gâche et l'autre a infrarouge?
Can I connect the intercom with the lock without an 12v adapter with the same model?
Kis 604
?
no dear, this model intercom required 12V adaptor for lock
o dear, this model intercom required 12V adaptor for lock
no dear, this model intercom required 12V adaptor for lock
Can I connect to my nvr PoE ports instead of PoE switch?
Yes
Hello I have a DS KV8x13-M device. Is it possible to connect a small gate with magnetic lock + a double gate opener for a car to this device and how? :]]
use ivms4200 for enable lock 2
@@adshikvision so its just a software thing?
@@mischo1990 yes
Does this have motion detect feature?
ig you add outdoor camera to hikvision nvr you can set motion recording
are posibble 1set for 2 doors? or 3.
yes
hello. I could see visitors' photo in the app while using this device. I reinstalled for the new monitor, but now I can only see visitors as alerts. How do I set it up so I can see visitor photos?
login screen go to shortcut
there u need to enable capture option
How far away can I put the 12v to the lock? Mine is about 10 meters far
10 meter no issue.
use 12v 5 amp adaptor
@@adshikvision it the doorbell capable of giving the 12v to the lock?
@@goncalo_silva NO
@@adshikvision thanks
Its can be conected to the outomatic sliding gate?
yes
Ip intercom mein out door se lock ka
Kya colour code hai aap bata sakte hain kya
Dear there is mention pause video you can find..
Is there any way to take power from poe , and install it without push button
this model will not share power to lock. DS-KD8003IME1 will share poe power to lock
تسلم على المعلومات القيمه
Hi, I don't unbderstand how this is not a security risk. If you want to break into house you basicli need to just couple together two wires and thats it, the door opens for you. mabey I am missing something but I feel that the door opening rele should be on inside unit.
Its inside only. Unless sombodt taper it cannot be exposed
Bonjour je veux savoir comment connecter la platine de rue à l'écran
I m facing an error. Once someone ring the bell from outside nd it worked properly but if the person ring it again it didn’t showed up. It required few minutes then jt worked
update latest firmware on your all indoor screen
Does it work without the screen?
No
Sir without power Adaptor connect, i use Poe switch, tell me sir
Not possible
Posible
@@adilsiddqui5024 can you share how to do that?
Hola buenas tardes, a mí lo que me gustaría saber, es a donde está conectado el frente de calle, y el monitor, ya que los dos tienen distintos cables tipo utp
todos deben estar conectados en la misma red
Is it wifi ,can we connect with out lan cable from out door camera to indoor monitor
yes
603 vdp without POE connect kar sakte hain? If yes, how?
No dear...
If I have already in place a KIS-203 device connected on 4 wires, can I replace it with KIS-602 without POE? Which will be the wires that I have to use?
no dear, Need network cable
ماهو كرت TF في الانتركم نوع هيك فجن
memory card. SD card, you can insert sd card in indoor station for photo capturing
awesome vid thanks
Glad you enjoyed it
What If I power the Doorbell with PoE, will work too?
PoE give power only for intercom device , you need additional adaptor for lock
Thanks i was going to ask the same question
How has the outdoor unit held up over the year?
Hola. Perfecta explicación. Tengo éste equipo, pero en mi caso quiero conectar el frente a un portón para realizar la apertura automática. Sería ésto posible? Gracias!
sí tu puedes
Awesome video! They claimed that it is possible to make the chime gong via doorunlock wiring. Maybe you know better..
yes
How to terminate no touch button to hikvision panel please help sir
No touch button give power 12V and also connect No touch button NO & COM to AIN3 & GND. that's all
Как отключить гудки на панели что находится при входе в квартиру, гудит на весь подьезд
может вы неправильно почините наружное устройство
это тамперная сигнализация
может вы неправильно почините наружное устройство
это тамперная сигнализация
пожалуйста, проверьте
Como ligar os cabos
QUE EXTREMO DEL CABLE
Great Video!
Thanks!
ruclips.net/video/fkWaSJWv4v0/видео.html&ab_channel=ADSHikvisionTech
Mine is a little different, I had to used the NC instead of NO
@@carloboy24 its depend up on a NC or NO lock
Is there a way to contact you
+971551846637
thanks very nice ....i like
Thanks for liking
How to fix calling failed when you door bell
Restore to default all device and re configure
ruclips.net/video/NFa8z0uqVdg/видео.html&ab_channel=ADSHikvisionTech
In the whole video, he was seen only doing wiring, in the last second when the function starts, the video ends
this is a realy lame desing... i just snap the plastik button case and conect two wires and open the door from outside... thanks for the video i almoust bought it...
Haga otro video en spanish
In vdp DS-kV6113-WPE1 there is a terminal AIN1 and GRD, with 5v in open condition, to connect door sensor alarm, after connecting a reed swtich door sensor, where to configure alarm, whether alarm will display in Monitor DS-KH6320-WTE1 or in Hikiconnect phone. I have connected a magnetic reed contact on the terminal but no alarm aprears anywhere. Please help
After connecting a door contact sensor to DS-KV6113-WPE1(C) for alarm, where do we get alarm? There is a provision on DS-KH6320-WTE1 display station and it works giving alarm. But usually door contact wiring is near to door and vedio phone, again multiple outdoor station requires door contact to be connected to phone station as only one door contact alarm can be configured in display