Hello bro. I got .22 uragan too. What is the best setting (v, speed/energy) for 50-70 meters accuracy in your opinion (jsb 1.17g) ? Which pellets are better suited for distances over 50 meters? I have jsb jumbo heavy 1.17g - 18.13grs, jsb jumbo beast 2.2g - 33.95grs, jsb straton jumbo monster 1.64g-25.39grs How many do you load the cylinder to? I usually go to 250-280bar (3600-4000 psi).
After you got the regulator out of the housing, how did you say you adjust the regulator, as you only show pics of this process, could you show or explain in more detail how you adjusted the regulator please, and could the trigger pull just be adjusted too increase by a very small amount without taking the regulator out?
Hi, do you have a measured cavity between the top and bottom of the regulator?My hurricane is limited and I don't know how many bars it's tuned to until I get the correct answers.
Hey Sniper, I adjusted my regulator like you did. But now when I try to air the rifle back up, air just escapes from the barrel and the side that the regulator is on. Any ideas of why it is doing this?
@@comedygalata8802 once I readjusted the regulator by turning the brass screw all the way in until it wouldn’t go any farther, I was able to air it up then. So every time I adjust the brass screw even a little, it want air up even when I cock the rifle.
Yes.... offcourse we were used huma as well we got speed more than 950 fps with jsp 18gr pellet. The Regulator pressure 140 bar.. also we need to adjust the spring little bit.
@@sniper7720 I have the .25 King. - So any suggestions as to what bar I should start with adjusting the HUMA? 140bar as you mentioned? Should I go a quarter turn heavier on the trigger spring too? Thanks!
Sorry still i not check with .25 cal . But you can try 140 bar huma regulator. Then trying to adjust the spring slowly until you will get the maximum speed.
And one more thing about king cylinder. When you fill air by compressor. Don't fill at one time take 2 or 3 times better . We were noticed 2 riffle the king. After few month the Regulator fully scaling and become rusty.. because of moisture.. so take care . Or use any filter.
@@sniper7720 youtube video paarthudhan bro indha gun different technology bro yannaku romba puducha rifle. I have one nx200 just one year before I got the rifle.... I'm using air rifle last 16 years till now
Sorry for delay.. for increase the pressure counter clockwise. Better loose the black nut then turn the center screw and tight the black nut. But this method little complicated because we need to mark the starting point and finishing point .
Hello bro. I got .22 uragan too.
What is the best setting (v, speed/energy) for 50-70 meters accuracy in your opinion (jsb 1.17g) ?
Which pellets are better suited for distances over 50 meters?
I have jsb jumbo heavy 1.17g - 18.13grs, jsb jumbo beast 2.2g - 33.95grs, jsb straton jumbo monster 1.64g-25.39grs
How many do you load the cylinder to?
I usually go to 250-280bar (3600-4000 psi).
After you got the regulator out of the housing, how did you say you adjust the regulator, as you only show pics of this process, could you show or explain in more detail how you adjusted the regulator please, and could the trigger pull just be adjusted too increase by a very small amount without taking the regulator out?
Where did you get it from, can one get it in india.pls post the 50yds group
Hi, do you have a measured cavity between the top and bottom of the regulator?My hurricane is limited and I don't know how many bars it's tuned to until I get the correct answers.
Sorry boss I don't know that measurment . You can check in Google .may you can find . Anyway thank for commons and sorry for helpless
Hey Sniper, I adjusted my regulator like you did. But now when I try to air the rifle back up, air just escapes from the barrel and the side that the regulator is on. Any ideas of why it is doing this?
Sorry for late reply. Normaly it hapen on emty cylinder. First cock the gun then you fill.
@@comedygalata8802 once I readjusted the regulator by turning the brass screw all the way in until it wouldn’t go any farther, I was able to air it up then. So every time I adjust the brass screw even a little, it want air up even when I cock the rifle.
What about replacing with a HUMA reg?
Yes.... offcourse we were used huma as well we got speed more than 950 fps with jsp 18gr pellet. The Regulator pressure 140 bar.. also we need to adjust the spring little bit.
@@sniper7720 I have the .25 King. - So any suggestions as to what bar I should start with adjusting the HUMA? 140bar as you mentioned? Should I go a quarter turn heavier on the trigger spring too? Thanks!
Sorry still i not check with .25 cal . But you can try 140 bar huma regulator. Then trying to adjust the spring slowly until you will get the maximum speed.
And one more thing about king cylinder. When you fill air by compressor. Don't fill at one time take 2 or 3 times better . We were noticed 2 riffle the king. After few month the Regulator fully scaling and become rusty.. because of moisture.. so take care . Or use any filter.
@@sniper7720 Thanks!
Bro where are you from.I'm from india,tamilnadu state. can I get the .177 cal uragun. In .177 how many ft lbs it delivered...
I am also tamil . But now in UAE. I don't know there is available or not . But in uae available not a 177cal. .22 only
Thanks for reply brother.....bro kalakkunga uragun Sema gun ...Andha gun performance Vera level brother
Yes bro
How you know about uragun you have in using ?
@@sniper7720 youtube video paarthudhan bro indha gun different technology bro yannaku romba puducha rifle. I have one nx200 just one year before I got the rifle.... I'm using air rifle last 16 years till now
.22 cal should have at least 50 joules!
5:16 turn clockwise or counterclockwise
Sorry for delay.. for increase the pressure counter clockwise. Better loose the black nut then turn the center screw and tight the black nut. But this method little complicated because we need to mark the starting point and finishing point .
@@abihajatpk let me ask more i want to increase capacity from 16j to max where do i adjust. thank you
Is the last screw in the back
If you want you increase the speed little bit open the regulator as well tight the hammer spring step by step
tem em português é melhor