I am so grateful for your video. Thank you for not gate keeping because I can not afford a technician and am pretty sure other families can't either. Thank You and God Bless You.
Man, I will have to say your videos are the Best, out all the vides I have watched yours are # 1 The are short, detailed and to the point. gets the job done.
The amount of talking is Just Fine. So is the pace of your descriptions. I've watched videos that are faster and louder, and they do me no good. Thanks for this video and for answering your Comment questions.
I just fixed mine in just over an hour after a little wrestling around. It finally submitted after the Australian toe hold followed by the choke hold!😁 thanks for the great video!!!
This video was amazing I just replaced the suspension rods in my moms washing machine and it was so simple. Even with no background, I was able to follow and complete the job.
Very well done as always. The one time I had problems with shaking and making loud banging noises was that one time I ate at Chipotle. 😀 Hope you have a great weekend ahead!
I also have a washer only a couple years old , whirlpool, piece of crap! They are all made by whirlpool. Do yourself a favor and pay the extra money for a speed queen
For others here: 1: use a level and check front to back side to side, feet on bottom of unit can be adjusted to lvl by hand usually (can use a Dolly or something similar to slightly lift front/sides and slip a wedge under to adjust feet gradually if ya don't have a helper) make sure rubber type vibration pads on feet aren't broken/missing while you're there. 2: if you have an agitator check if it's wobbly, if so than check for damage around the nut that holds it in center under its cap and replace agitator if it's broken there, otherwise remove nut and pull agitator out to check for worn out smoothed/broken teeth between spline gear and agitator and replace if so. 3: for bottom plate agitator style models with no center agitator remove the plate to check plastic&metal splines for damage, if plate teeth are smoothed out/broken but spline is fine replace the agitator plate. 4: Replace rods/springs if all else checked out fine. 5: if none of that works and your unit has a suspension bracket setup between metal housing and bottom of basket/motor mount area under washer tub check if any of it slipped outta alignment and correct it and check if your unit uses damper pads usually between the brackets under motor mount area and inspect+replace if they're bad, they're typically a thin plastic material slightly bent in a partial circle form (find a parts breakdown diagram for your unit in manual/online to see if it uses damper pads anywhere and for part numbers for 'em to replace if needed). 5: Slightly useful bumper rig you shouldn't need to do if everything is in working order after fixing it all but I've fastened some pipe insulation/pool noodle to the inside housing of one of my units to add cushion before by drilling a couple holes on left&right side for big zip ties to go through to hold the insulation in place, I don't recommend doing it but it's helped me with balance issues in the past. Hope this helps someone.
Thank you, this was very straightforward. Is their any other reason a washing machine is shaking? We adjusted the feet so it doesn't wobble, just checking to see if it might not be something else.
Very informative video. The back of my Maytag washer vibrates & has done so since it was new. I hooked a piece of rope on the back & pulled it tight toward the front of the washer which helped so I’m wondering if maybe the screws were not tightened. Will have to check. It’s worse when I wash jeans & I’ve cut the load size down considerably. Thanks for sharing such a great repair video. Very well done!
My washer was 90% identical; however, the drum was completely suspended by the rods/springs... if you follow the video's instructions on how to get the right part, you should be fine (Yes, I got mine from Amazon too). In my case, I found it easier just to pull the washer out completely and lay it on its side - that "zeroes" the tension on the "top" springs and they are easy to replace. Flipping it over has the same effect. When repaired and reset upright, you may need to 'bounce' the tub a bit manually for everything to set... Once it does, yes, it can still side/side but it is difficult to go up/down. My guess is the "free form/ Side-to-side" thing is so it can judge the load size. But the repair worked like a charm - $40- over $400? sign me up!
I have a whirlpool WTW4815EWO I bought suspension rods from Amazon. It says compatible. I noticed the plastic pieces that fit in the whole n cup the rod fit into are slightly different. They don’t look like fit securely in the frame. So I used the old ones. Put back together but machine is still banging. Also the drum still feels like had sake slack in it. Not firm.
replaced suspension rods with Chinesium and well, it didn't last long. If you have to wait to get USA made parts, do so, its worth the wait and the money.
True, but he gets them virtually for free and sells them to other people. I’d put the cheapest parts in I could if I was reselling them, but if I were keeping them I’d get US made parts.
I bought the wrong suspension rod mine is 2DWTW4845EW1. The one i got from Amazon was shorter than the one in Washer. I need to get the correct one using the model number
I have a Bravo model of Maytag and it would spin out of balance. I just changed the suspension rods and that solved the problem for about 5 washes. Now it's out of balance again. I did the re-calibration and the Spin light stayed on and blinking. Any advice?
hello, yesterday I bought new washing machine and I forget to remove 4 bolt screws from the back. and I had start washing clothes and after few minutes my machine got noise and i plugged off and i saw one bolt screw broken down on the floor. after that i remove all bolt screw from the machine. i am worried about the half part of the screw inside the machine. I just want to know is it safe for machine or what happened?
Thanks for the instruction. I’m curious, what’s wrong or what’s the malfunction of the suspension rods? Our machine is banging significantly on spin. Seems easy but I’d like to know what’s wrong with the rods. How did they fail?
It's a combination of the dampening grease used in the aid of smoothly compressing and decompressing the springs rubbing off and the internal foam inserts wearing out.
How do you know if they are bad by looking down in there at them? Or are you going by age, assuming if 10 years old, that’s the problem? I’m about to throw in the towel & just buy a new speed Queen, because we’ve already replaced 2 parts & it worked at first but now not spinning out all the way. It just keeps adding rinse water, drain & spin & then done & clothes are heavy wet but no standing water. 😢 8 year old Maytag. Great video though. So appreciate your detailed info!!!
Best thing to do is get the is search a website like www.appliancepartspro.com by model number of your washer. This will ensure you get the correct suspension rods
Love how you explain everything as you go! I replaced my rods but think I’m going to have to replace the hub, it’s still shaking. Also need to replace the sound absorbers on both sides. 🤞🤞🤞
@@logmat45 The black pads on the left and right of the tub. They are near the top. Just 3” x 3” foam pads sticky on one side so the tub doesn’t bang against the enclosure.
I replaced the springs, but my washer still shakes violently when spinning. The issue is not the load being out of balance. Do you know what else could cause this? Thanks.
Try replacing the hub. You will have to remove the agitator and you will see it. I have a video on it as well. ruclips.net/video/pkzJa_5PrRc/видео.html
Great video, I just replaced the plastic to metal flange but fear I need to replace the rods too because it still bounces up and down when pushed down.
I have replaced the rods in my Cabrio and now it will spin at high speed and not bang around. However when agitating the drum slams into the sides every time the agitator changes direction. The bearings need replacing and I will be doing that next when I get the kit. But scratching my head over such a wide movement of the tube during agitation when that was not an issue before I replaced the rods. Any thoughts on this?
How long do most suspension rods last? My washer is only 4 yrs and moves everywhere on the spin cycle. I am assuming it's the rods that need replacing.
It all depends on how you have used the washer. If you overload it consistently, you will be lucky to get a yese or two out of the rods. Without knowing all the details, I would say 4 years for the rods is not bad
We took the rods out one by one and inspected them but nothing appeared to be wrong or broken with them on my dads whirlpool washer. Could they still be bad? The machine does shake and is loud on spin cycle and the foam pads on the left and right insides are worn through from the drum banging the sides. The front and rear pads look fine. The machine is maybe 5 years old.
My man!! Just got the OEM parts delivered today and installed them in about 20 minutes. There was a commenter (either on this video or another I don’t remember) who said not to get the Amazon ones and to get OEM. So it cost $110 for all 4 suspension rods. Installed super easy with your instructions, and now the washer is spinning like a top! Thank You!!
Open top top of the washer go to the hardware store and get something called camper seal it’s flexible tape that sticks to the sides of the washer take off all the black padding and replace it with camper seal problem solved I just did it a whirlpool washer
Bro thanks for ur videos. Question my maytag machine is 1 year old u thing thats the problem with mine??? It shakes like crazy. I hope u will answer my question thanks a lot again for ur helpful videos..🙏🏼🙏🏼
Yes it can be the suspension rods that are bad. It's definitely worth trying! If it is not the rods, then most likely, the inner tub is beginning to strip, which would be much more of an expensive (probably not worth it) repair. I make sure the washer is completely level and then replace rods.
Hello, i have a Maytag washing machine and when the spin cycle starts the washing machine stars making a lot of noise, im thinking bearings(?). I've also cleaned the light sensor that sits on the actuator since it was covered in a thin layer of dried mud so the washing machine wouldn't work. Now that its cleaned it works, but over time a little puddle of water forms under the machine. So im thinking that a seal went bad, causing a small leak that affected a bearing and also caused the build up of dirt on the sensor. I dont know anything about washing machines but i plan to work on it myself since theres a few people that would fix it where I live. So if you could help me i would be very grateful.
Same here!!! I guess this guy was unaware that there must be another reason it does this inwhich this video does NOT fix the issue. I hate it when people say this is your problem & this will fix it, & it doesn’t whatsoever. You probably shouldn’t be making such claims then huh?
Hi DuctTapeMechanic! I just subscribed! Question for you, is it likely to be anything other than the suspension rods? The hub axle seems fine but I do have water between the inner and outer drum and I am wondering if that could be the culprit for the crazy shaking? After I opened up the top I put the washer on spin with nothing inside and it spun smoothly.
I would check to see if there is significant play between the inner and outer tub (it should be tight). If there is play, then your inner tub is stripped (time for new washer). If there is no play, try pushing down on the agitator with your hand if it bounces around a couple times the suspension rods are bad (good rods should only bounce back once or twice). Running it without any cloth won't tell you much. Hope this helped.
My tub is huge and no room to squeeze my arm down to lift the rod up into the top hole. So I used the clip end of my dog’s leash to grab the hook on the top of the rod and pull the it up thru the hole! HA!
I replaced my drain pump and then ran a wash cycle to make sure it was good. But the wife ran a load and now it shakes like freaking crazy! What did I do wrong??
Most probably he’s right & your inner tub hub is stripped out. To check, look down into the tub and imagine there’s a clock. See if you can rock the inner tub 6-12 o’clock. Depending on the model the hub can be replaced. If you’re not experience you need a guy like him to do it because it’s kinda “internal” & has multiple steps to it. Most improbable your suspension rods are seated or is missing a plastic bearing, or are wrong length, or mistakenly reinstalled old rods, etc (all things I’ve seen happens but probably it’s the hub). Good luck man 🙏
U really talk too much about nothing. After watching video i need to amend my first sentence. The beginning was annoying due to the needless talking but the rest of the video was spot on. Thanks for an informative video.
I am so grateful for your video. Thank you for not gate keeping because I can not afford a technician and am pretty sure other families can't either. Thank You and God Bless You.
You're welcome! Appreciate the kind words!
Thank you brotha, it’s ppl like you that make RUclips great.
Thank you!
Man, I will have to say your videos are the Best, out all the vides I have watched yours are # 1
The are short, detailed and to the point. gets the job done.
The amount of talking is Just Fine. So is the pace of your descriptions. I've watched videos that are faster and louder, and they do me no good.
Thanks for this video and for answering your Comment questions.
Appreciate the support!
In this hard economy a video like this is gold thank you for your video and helping me save money
The economy is fine. Just ask a Democrat. Lol
You are a master teacher! Pleasant and clear explanation. Thank you!
I appreciate the kind words glad I could help!
I just fixed mine in just over an hour after a little wrestling around. It finally submitted after the Australian toe hold followed by the choke hold!😁 thanks for the great video!!!
This video was amazing I just replaced the suspension rods in my moms washing machine and it was so simple. Even with no background, I was able to follow and complete the job.
Awesome! Great job on getting it fixed!
Paid for good washer got junk pool is full of shit they beter fix this shit...
Thank you for showing me how to replace the suspension rods. $50 fix instead of buying a new one
Awesome! Great job on doing it yourself! Glad I could help!
You is the man to fix anything I fix my washer looking at yo videos. Keep the videos coming brother
You really sound like a teacher. Very well done video. Congratulations!
Thank you for the kind words!
Great video..I like the way you explain things (the instructions) and then do it just like you said..well done..keep them video coming.
Appreciate the kind words!
Very well done as always. The one time I had problems with shaking and making loud banging noises was that one time I ate at Chipotle. 😀 Hope you have a great weekend ahead!
😂😂
Lmmfao
I’ve gotta look into this! We have a 2 year old with the same issue. By far this is the best explanation on suspension rods. Thank you my friend! 👍🏼
Best of luck!
I also have a washer only a couple years old , whirlpool, piece of crap! They are all made by whirlpool. Do yourself a favor and pay the extra money for a speed queen
For others here:
1: use a level and check front to back side to side, feet on bottom of unit can be adjusted to lvl by hand usually (can use a Dolly or something similar to slightly lift front/sides and slip a wedge under to adjust feet gradually if ya don't have a helper) make sure rubber type vibration pads on feet aren't broken/missing while you're there.
2: if you have an agitator check if it's wobbly, if so than check for damage around the nut that holds it in center under its cap and replace agitator if it's broken there, otherwise remove nut and pull agitator out to check for worn out smoothed/broken teeth between spline gear and agitator and replace if so.
3: for bottom plate agitator style models with no center agitator remove the plate to check plastic&metal splines for damage, if plate teeth are smoothed out/broken but spline is fine replace the agitator plate.
4: Replace rods/springs if all else checked out fine.
5: if none of that works and your unit has a suspension bracket setup between metal housing and bottom of basket/motor mount area under washer tub check if any of it slipped outta alignment and correct it and check if your unit uses damper pads usually between the brackets under motor mount area and inspect+replace if they're bad, they're typically a thin plastic material slightly bent in a partial circle form (find a parts breakdown diagram for your unit in manual/online to see if it uses damper pads anywhere and for part numbers for 'em to replace if needed).
5: Slightly useful bumper rig you shouldn't need to do if everything is in working order after fixing it all but I've fastened some pipe insulation/pool noodle to the inside housing of one of my units to add cushion before by drilling a couple holes on left&right side for big zip ties to go through to hold the insulation in place, I don't recommend doing it but it's helped me with balance issues in the past.
Hope this helps someone.
Saving this for when I take mine apart!
Thank you, if your able to do a video that will be more affective.
Is it possible to show what was actually wrong with the suspension? Just trying to learn. 😊 Thank you for showing how to replace them.
Check out ‘Washer Dryer Money’ video titled ‘Cheap Permanent? Fix for Shaking banging washer? $7 to fix…’
He explains why.
@@willsalicia Thank you
Great video, even I got it. What does a 4 set of those cost? Thanks
Thank you, this was very straightforward. Is their any other reason a washing machine is shaking?
We adjusted the feet so it doesn't wobble, just checking to see if it might not be something else.
Making this repair stopped my washer from trying to self-destruct in the spin cycle.
great video, thanks. life hack for me was to use the old rod J hooks to lift the new ones through
Great tip!
I have same washer but mines only shake during spin cycle where do u think I should start first?
Wow! What an informative and easy -to-understand and clear video! Thank you very much!
Very informative video. The back of my Maytag washer vibrates & has done so since it was new. I hooked a piece of rope on the back & pulled it tight toward the front of the washer which helped so I’m wondering if maybe the screws were not tightened. Will have to check. It’s worse when I wash jeans & I’ve cut the load size down considerably. Thanks for sharing such a great repair video. Very well done!
Thanks for your knowledge you showed me how to replace my rods and fix my washing machine. Job done well Kudos.
Great work! Glad you got your machine working!
Nice video, very clean. My neighbor's dogs bark. Makes me feel at home.
Is there any video to fix the same problem for those advance digital whirlpool laundry machine. It shakes and keeps bagging against the wall
My washer was 90% identical; however, the drum was completely suspended by the rods/springs... if you follow the video's instructions on how to get the right part, you should be fine (Yes, I got mine from Amazon too). In my case, I found it easier just to pull the washer out completely and lay it on its side - that "zeroes" the tension on the "top" springs and they are easy to replace. Flipping it over has the same effect. When repaired and reset upright, you may need to 'bounce' the tub a bit manually for everything to set... Once it does, yes, it can still side/side but it is difficult to go up/down. My guess is the "free form/ Side-to-side" thing is so it can judge the load size.
But the repair worked like a charm - $40- over $400? sign me up!
What do you level these aligned machines off of?
Wheres a flat part of the machine?
I have a whirlpool WTW4815EWO I bought suspension rods from Amazon. It says compatible. I noticed the plastic pieces that fit in the whole n cup the rod fit into are slightly different. They don’t look like fit securely in the frame. So I used the old ones. Put back together but machine is still banging. Also the drum still feels like had sake slack in it. Not firm.
Thank you so much, I was successfully able to fix the issue myself without calling anyone!
Awesome! Glad to help!
replaced suspension rods with Chinesium and well, it didn't last long. If you have to wait to get USA made parts, do so, its worth the wait and the money.
Agreed. Happened to me once as well
Made that mistake as well.
Where did you buy the USA made?
local to where I live, an independant parts store. I have to ask for original parts, not chinesium. @@herewegoagain7135
True, but he gets them virtually for free and sells them to other people. I’d put the cheapest parts in I could if I was reselling them, but if I were keeping them I’d get US made parts.
A very good explanations, but what was wrong with the rods removed?
@josephcriminale9188 the foam insulation wears out, or sometimes the dampening grease runs dry
You got a link for the rods please
Thanks a million! I found the parts at Amazon. My machine is an Admiral Brand. Super easy to replace thanks again!
I had whirlpool mod WTW4950XW2. Do you by any chance have instructions how to get to rods? .It’s different to what you show in your video. Thanks
I bought the wrong suspension rod mine is 2DWTW4845EW1. The one i got from Amazon was shorter than the one in Washer. I need to get the correct one using the model number
I have a Bravo model of Maytag and it would spin out of balance. I just changed the suspension rods and that solved the problem for about 5 washes. Now it's out of balance again. I did the re-calibration and the Spin light stayed on and blinking. Any advice?
Thanks!
You're welcome! Thanks for supporting the channel!
hello, yesterday I bought new washing machine and I forget to remove 4 bolt screws from the back. and I had start washing clothes and after few minutes my machine got noise and i plugged off and i saw one bolt screw broken down on the floor. after that i remove all bolt screw from the machine. i am worried about the half part of the screw inside the machine. I just want to know is it safe for machine or what happened?
Our washer does that we changed all 4 rods and it's still doing it anything else it could be? It's a Maytag
My whirlpool does that but it ain't that old what if it ain't the suspension rods ?
Thanks for the instruction. I’m curious, what’s wrong or what’s the malfunction of the suspension rods? Our machine is banging significantly on spin. Seems easy but I’d like to know what’s wrong with the rods. How did they fail?
It's a combination of the dampening grease used in the aid of smoothly compressing and decompressing the springs rubbing off and the internal foam inserts wearing out.
How do you know if they are bad by looking down in there at them? Or are you going by age, assuming if 10 years old, that’s the problem? I’m about to throw in the towel & just buy a new speed Queen, because we’ve already replaced 2 parts & it worked at first but now not spinning out all the way. It just keeps adding rinse water, drain & spin & then done & clothes are heavy wet but no standing water. 😢 8 year old Maytag. Great video though. So appreciate your detailed info!!!
Can I start with the back rods of the washer machine?
Yes. Should not be an issue
How can I get the part number you used? I have the exact same washing machine. Not sure which one to order.
Best thing to do is get the is search a website like www.appliancepartspro.com by model number of your washer. This will ensure you get the correct suspension rods
Where could get the rod
were did you get the part for the machine?
Thanks for the video, I just lubed the cup the suspension rod bearing rides in and the noise went away.
Great job! I have done that on a Samsung myself!
Love how you explain everything as you go! I replaced my rods but think I’m going to have to replace the hub, it’s still shaking. Also need to replace the sound absorbers on both sides. 🤞🤞🤞
Thank you! Best of luck in your repair!
What are the sound absorbers ?
@@logmat45
The black pads on the left and right of the tub. They are near the top. Just 3” x 3” foam pads sticky on one side so the tub doesn’t bang against the enclosure.
That’s my washer. Bought it for the simple technology. Good ol basic construction but I have this imbalance problem
Does it matter which way the hook is facing
I replaced the springs, but my washer still shakes violently when spinning. The issue is not the load being out of balance. Do you know what else could cause this? Thanks.
Try replacing the hub. You will have to remove the agitator and you will see it. I have a video on it as well.
ruclips.net/video/pkzJa_5PrRc/видео.html
Do you replace the cheap plastic hub with the metal one?
@@DuctTapeMechanic link not open
What is the average cost of a suspension rod?
what makes it clunk? one of the springs loses tension?
Dampening grease and foam fillings wear down on the rods
Great video, I just replaced the plastic to metal flange but fear I need to replace the rods too because it still bounces up and down when pushed down.
Thank you!
I have replaced the rods in my Cabrio and now it will spin at high speed and not bang around. However when agitating the drum slams into the sides every time the agitator changes direction. The bearings need replacing and I will be doing that next when I get the kit. But scratching my head over such a wide movement of the tube during agitation when that was not an issue before I replaced the rods. Any thoughts on this?
Check to see if bolt that holds the stator on at the bottom is loose
WHO'S Better than You!!! Good Stuff. Thanks
Do you have to insert from the bottom of the washer? Can you drop it down from the inside of the washer?
Where do you buy the replacement suspension rods
Appliance parts pro is a good site. You can also buy them from whirlpool
@@DuctTapeMechanic Thank y ou
Great video, thanks! Didn't notice the dog barking until you mentioned it. 😆
Awesome video! Could you tell me where I could buy the suspension rods?
The appliance parts pros website is pretty good for ordering quality parts
Where does the part that puts water in the machine go.
How long do most suspension rods last? My washer is only 4 yrs and moves everywhere on the spin cycle. I am assuming it's the rods that need replacing.
It all depends on how you have used the washer. If you overload it consistently, you will be lucky to get a yese or two out of the rods. Without knowing all the details, I would say 4 years for the rods is not bad
Were u buy your parts from
We took the rods out one by one and inspected them but nothing appeared to be wrong or broken with them on my dads whirlpool washer. Could they still be bad? The machine does shake and is loud on spin cycle and the foam pads on the left and right insides are worn through from the drum banging the sides. The front and rear pads look fine. The machine is maybe 5 years old.
Trying pushing the middle of the agitator down, if it bounces around like crazy that means the suspension rods are bad
When putting your old rods back in did it fix the problem?
I bought the wrong suspension rod. How do i find the correct one for Whirlpool
The best thing to do is search by the model number of your washer
@@DuctTapeMechanic the model number is 2DWTW4845EW1 but I cant find it
How do I tell if my suspension rods are bad. I took one out and I can’t tell.
It looks fine to me
Push the top of the agitator if the tub wobbles a lot after you release, then you need suspension rods
@@DuctTapeMechanic thanks man. Just ordered the replacements
My man!! Just got the OEM parts delivered today and installed them in about 20 minutes.
There was a commenter (either on this video or another I don’t remember) who said not to get the Amazon ones and to get OEM. So it cost $110 for all 4 suspension rods. Installed super easy with your instructions, and now the washer is spinning like a top!
Thank You!!
I replaced my suspension rod and it keeps banging. Even when I put a small load in and even it out. The machine bangs like crazy
Did you figure out what it was ?
I’m having the same issue too. Seems better but something else is still going on. Seems like it starts to shake then something kills the spin cycle
@@keithadams5970look up Josh Cobb his video solves this it’s really simple fix
Did you hook the bearing right? When you put the hook in you only need to turn it 1/4 of the way. If you turned it too much it will shake.
Open top top of the washer go to the hardware store and get something called camper seal it’s flexible tape that sticks to the sides of the washer take off all the black padding and replace it with camper seal problem solved I just did it a whirlpool washer
Bro thanks for ur videos. Question my maytag machine is 1 year old u thing thats the problem with mine??? It shakes like crazy. I hope u will answer my question thanks a lot again for ur helpful videos..🙏🏼🙏🏼
Yes it can be the suspension rods that are bad. It's definitely worth trying! If it is not the rods, then most likely, the inner tub is beginning to strip, which would be much more of an expensive (probably not worth it) repair. I make sure the washer is completely level and then replace rods.
I replaced mine but its still banging around like crazy..any tips?
where did you purchase the rods from? Amazon rods are a real hit or miss
@DuctTapeMechanic i bought from a store and it did take the bounce out of the tub but still unbalanced the top of it is hitting the side walls
I have Maytag bravos. I changed all four shocks and it shakes like crazy.
Check to see if tub nut is tight
If it is then most likely your tub hole js stripped out. Time for a new washer
Hello, i have a Maytag washing machine and when the spin cycle starts the washing machine stars making a lot of noise, im thinking bearings(?).
I've also cleaned the light sensor that sits on the actuator since it was covered in a thin layer of dried mud so the washing machine wouldn't work. Now that its cleaned it works, but over time a little puddle of water forms under the machine.
So im thinking that a seal went bad, causing a small leak that affected a bearing and also caused the build up of dirt on the sensor.
I dont know anything about washing machines but i plan to work on it myself since theres a few people that would fix it where I live. So if you could help me i would be very grateful.
So I think I need to do this ruclips.net/video/EQmpLMAsi8g/видео.html
Plus a bearing, where that would be located?
The bearing is on the transmission and can be very difficult to pull off from.
@@DuctTapeMechanic it'll be a great challenge me then... Anyways thank you for responding.
I accidentally dropped a paper cloth behind the drum and cannot get it out. Is it a fire hazard?
Where can i buy new suspension rod!
For suspension rods, I recommend the appliance parts pro website
I changed the balancing rods and still bouncing around. Ugh.
Same here!!! I guess this guy was unaware that there must be another reason it does this inwhich this video does NOT fix the issue. I hate it when people say this is your problem & this will fix it, & it doesn’t whatsoever. You probably shouldn’t be making such claims then huh?
Thanks for the help! This should be easy to fix on mom's machine. Plus save her the $80 serves call fee.
Awesome! Best of the luck with the repair!
How do u know if it is the rods or maybe machine is not balance?
Push down on the agitator if it bounces up and down like crazy its the rods.
Hi DuctTapeMechanic!
I just subscribed! Question for you, is it likely to be anything other than the suspension rods? The hub axle seems fine but I do have water between the inner and outer drum and I am wondering if that could be the culprit for the crazy shaking? After I opened up the top I put the washer on spin with nothing inside and it spun smoothly.
I would check to see if there is significant play between the inner and outer tub (it should be tight). If there is play, then your inner tub is stripped (time for new washer). If there is no play, try pushing down on the agitator with your hand if it bounces around a couple times the suspension rods are bad (good rods should only bounce back once or twice). Running it without any cloth won't tell you much. Hope this helped.
@@DuctTapeMechanic It did! It was the suspension rods and I replaced them one at a time per your video! Thanks again for your videos!
@@TrebyZ You're welcome!
What if I replaced these but it is still shaking bad
Most likely the tub nut is either loose or your tub is stripped in which you will need to purchase a new washer
THANK YOU! I was able to fix my machine. It works perfect now!
You're welcome!
Where do you get the parts from???
Amazon mostly
My Maytag only grinds in agitation mode. Would that also be the clutch?
I would replace clutch and shifter (it could be a weak shifter). Both parts combined are only like $50
Do you need to replace all of them?
Yes all at the same time
Great teacher!!!
Very helpful!
Thank you!
Sooo easy to understand. Thank you soooo, much!!!❤
This is the best video who need their washer fixed ?😂
So what is actually wrong with the rods?
My tub is huge and no room to squeeze my arm down to lift the rod up into the top hole. So I used the clip end of my dog’s leash to grab the hook on the top of the rod and pull the it up thru the hole! HA!
Ingenious! Great job!
Thanks for going through it twice.
I just replaced the suspension rod in my washing machine but when i used it, the machine is still banging
Mine too. I'm still looking to see what else it could be
Love ya dude! Thanks for the help! ❤
Happy to help!
I replaced my drain pump and then ran a wash cycle to make sure it was good. But the wife ran a load and now it shakes like freaking crazy! What did I do wrong??
I’m confused. The rods don’t appear to be broken so why is the machine moving around and banging?
The rods (specifically the dampening grease and foam) wear out over time
Thanks!!! Hi from Maui !
You're welcome!
I did this repair and the washer still shakes. Any ideas?
Most likely inner tub is stripped from being overloaded
Most probably he’s right & your inner tub hub is stripped out. To check, look down into the tub and imagine there’s a clock. See if you can rock the inner tub 6-12 o’clock.
Depending on the model the hub can be replaced. If you’re not experience you need a guy like him to do it because it’s kinda “internal” & has multiple steps to it.
Most improbable your suspension rods are seated or is missing a plastic bearing, or are wrong length, or mistakenly reinstalled old rods, etc (all things I’ve seen happens but probably it’s the hub).
Good luck man 🙏
Good video and great job. Well done sir.
U really talk too much about nothing.
After watching video i need to amend my first sentence. The beginning was annoying due to the needless talking but the rest of the video was spot on.
Thanks for an informative video.
You're welcome, I guess....lol!
@@DuctTapeMechanic
I've watched some of ur other videos and ur good with explaining things clearly. Keep up the good work.👍👍
Thanks!! Explanation is great!!
Awesome glad to help!
Excellent video very simple
Thanks 😊!
Mines been doing it for a while now.. it's about 5 to 6 years old. I guess it's cheaper to try and fix it than buy a brand new one.
Absolutely!