hi Ludic, i had been trying recreating the circuit, (the capacitors you mentioned are not available so i use 3 kv ones) but my diodes keep getting damaged each time either the spark is too tiny or if i increase the input voltage, the diodes die, so can i use ESJA54-08A diode to create same circuit with more stages?
Everything working is meant to be taken apart. Letting it die is just cruel. Like how humanity is innately cruel because they decide to harvest organs only AFTER the thing has dieded. They should harvest it while you're alive, put you on life support and give you your own allotted time to press a button to end your life, only confirmable by a cheatcode-like input that follows. So you'll feel better about "leaving the earth". Up down up down left right left right square down down up
You say to remove everything from the high voltage side and that the output must be AC but at 1:53 I see a diode on the high side and maybe some chip plus that circuit board is not the same one you show in the beginning, also I noticed a few of your videos you show a different schematic than your circuit
Exactly, and you're stepping that voltage up so the voltage across the caps will be larger than the 9V input. If it wasn't, you wouldn't see anything on the spark gap!
You should replace weak transistor to bigger/stronger,it is easy to fry them.In my project the power source is 18650 cell ,that give me more current and working time.
You only want to run it for a couple of seconds at a time to prevent that as the transistor can't take it. You need a MOSFET and a big heatsink (but the pinout will be different).
Hmm, an interesting experiment with this voltage multiplier. You say that you have nearly 10 kV voltage, is it possible to charge a HV capacitor with these high potentials ?
Gracias por responder...lo replique,pero la salida de alto voltaje no es tan potente como la tuya. logre mejorar el circuito bajando el valor de la resistencia que tenia en el emisor...saludos!
+Ludic Sciencecan i use this one? www.aliexpress.com/item/100PCS-1N4007-4007-1A-1000V-DO-41-Rectifier-Diode/32375456677.html?spm=2114.031010208.3.1.TiYY87&ws_ab_test=searchweb201556_2_79_78_77_80,searchweb201644_5,searchweb201560_9
+victor morales si puedes añadir las etapas que quieras, cada etapa añade el doble del viltaje de entrada. Es imposible contestar a la pregunta de que tan peligroso puede ser, depende de muchisimos factores. ¿que tan peligroso es andar en automovil??? depende de muchas cosas. Lo mejor es tener siempre precaucion.
What transformer do you use to make the AC to DC? step up or step down Can we use step down transformer as step up if the wire is connected on the reverse side?
+LASER BEAR ASSAULT UNIT In this case the transformer outputs high frequency, but the voltage multiplier converts that to pulsated DC. You will feel a very nasty shock
+Sharp Paul It depends... the most important thing is that the current does not pass through the hearth. For example if you take both terminals with one hand, you will be shocked on the hand only, but if you take one terminal with each hand, then the current travels from hand to chest to hand through the hearth circuit, and that may be deadly.
+Ludic Science but the current will drop dramaticly as it has to pass through your body which acts like a resistor, and i think i remember from somewhere that it takes 5ma directly across the heart without the bodys resistance to kill you.
+Ludic Science It will hurt but it won't kill you. A new 9v battery has about 1A of current. If you step up the voltage to 10,000 volts, the current will drop to 0.0009A or 0.9 mA. You need about 70 mA to kill you.
Is it ok to widen the spark gap so that way I can have the switch engaged without me having to hold it down? It would be nice to walk away and let the destroyer auto pilot without the arc being engaged the entire time.
Hi, i have now taken away the parts from the fly swatter circuit that you did. But in the video you take the powersupply and put the parts on another cuircuit. I cannot see how you build the circuit. Please help me.
you could try but it's unlikely as the frequency of this circuit is equal to the resonance frequency of the transformer's primary coil, which is way lower than a tesla coil's resonance frequency
Thanks a lot for video. How can I make this power supply with 60 kV output with 220V AC input? Can you please help me which of your projects is appropriate for my purpose?
ok thank you for your response it helps me a lot, your videos are very inspirational and to convert it back to ac you can put it through a inverter circuit
Ludic Science Thing still confuse me that 1st stage output is 2 then as input to 2nd stage then it was 4 as output then as input to 3rd stage, it become 8 as you say in adds double of input . Unless you mean by it keep adding the voltage of original input in every stage.
+Gabriel Engel Interesting, not sure if the circuit really works. Looks to simple to be able to do that, especially with only 10 turns in the coil!!!! If I have ther ime I will try to replicate
+Pranal Ingle You need only the output from little transformer. Other components are not needed you have to remove. Output of entire flyswatter circuit is pulsed DC, not good for multiplier. Output from transformer is AC
do you still need the diodes for the discharge to be the same as when it was an electric flyswatter? im going to add a 10kv generator with 5 Metallized Film Capacitor 0.022uF 223J 2KV but dont know if i still need the diode for it to retain the original discharge elements of the electric flyswatter
Ludic Science so id only need the diode if i want to continue to step the voltage up? would i then want the resistor for the effect im looking for and if so what is the original resistor in the board? thanks for your help
have this set up powering a mini tesla coil, loads of fun from battery power. the coil itself is based on plasma channels 3v tesla coil. love the content Ludis Science, keep up the good work.
I've always had the most fun with a swatter circuit by adding five or six of the same capacitors paralleled into the output, it takes a bit longer to charge but the resulting explosions are well worth it. I usually take the paddle and grid off then attach two steel needles about 2 inches long on either side of the original handle and bend them inwards, so there's about 3/16" to a 1/4" of gap (4-6mm) between the tips. It becomes a bug _detonator,_ any insect caught between it's prongs become plasma vapor and little tiny bits of exoskeleton, the entire creature disappears in an instant. Safety glasses/squints are required🤣.
@@codeunited5905 that wouldn't work, or work very well anyways, the charge circuit only charges to 2kv, you would need to redesign it to reach the required voltage to max the caps out.
"And the output will be 4U (for you)"
it's a big voltage
Was looking for this comment
saw this exactly when he said "for you".
This is a really worth project to do.
This is an awesome project to create an arc reactor in big scale
hi Ludic, i had been trying recreating the circuit, (the capacitors you mentioned are not available so i use 3 kv ones) but my diodes keep getting damaged each time
either the spark is too tiny or if i increase the input voltage, the diodes die, so can i use ESJA54-08A diode to create same circuit with more stages?
what diodes are you using?
1n4007
This has given me an idea for a bottom-comb electron feed for my Van de graaff gen
1:30 The high voltage probe clearly loads the output, lowering the voltage. How many Megaohms is it?
Again nice video but please, don't tempt me to dismantle my working electric fly swatter XD
Everything working is meant to be taken apart. Letting it die is just cruel. Like how humanity is innately cruel because they decide to harvest organs only AFTER the thing has dieded. They should harvest it while you're alive, put you on life support and give you your own allotted time to press a button to end your life, only confirmable by a cheatcode-like input that follows. So you'll feel better about "leaving the earth". Up down up down left right left right square down down up
10,000V? isnt the 1n4007 rated for 1000V?
+chems the diodes don't see the full voltage. The final 10,000 volts are the SUM of the voltages in each stage. Same for the capacitors
You say to remove everything from the high voltage side and that the output must be
AC but at 1:53 I see a diode on the high side and maybe some chip plus that circuit board
is not the same one you show in the beginning, also I noticed a few of your videos
you show a different schematic than your circuit
Do you have a construction manual?
will the 9v battery instead of the 2 AA kill the circuit
+Reese Jespersen depends on the circuit, some cheap brands will burns in a few seonds.
Will 1kv capacitors work??
+Reese Jespersen No, but you can connect two in series to make one 2kv capcaitor
thank you for the info love your videos keep up the great projects
+Reese Jespersen Thanks!
What diode is use for this experiment?
Can I use 16v capacitors??? Or do I need 3kv???
16v caps will explode. You need caps of a voltage at least double the voltage of the source
voltage source is 9v tho... but i get it
Exactly, and you're stepping that voltage up so the voltage across the caps will be larger than the 9V input. If it wasn't, you wouldn't see anything on the spark gap!
Cuantos volts hay en la salida del circuito de la raqueta? Se puede usar el circuito que se usa para el flash de una camara?
could this run continuosly without burning out?
Thank you very much for this video.
I tried it, and it works very well. Thank you again !!!
Charles.
France.
Marseille.
Charles L Cheers
Bro can u email me the proer circuit diagram of this voltage multiplayer circuit. I really need it
ok so the circuit acts like add ups rather than an eventual rise in each capacitor at every continuous stage.thank you
I have a question why did you remove the components on the HV side?
James Huang those components are a small voltage multiplier. I removed them to pu my own multiplier
You should replace weak transistor to bigger/stronger,it is easy to fry them.In my project the power source is 18650 cell ,that give me more current and working time.
You only want to run it for a couple of seconds at a time to prevent that as the transistor can't take it. You need a MOSFET and a big heatsink (but the pinout will be different).
When running the circuit on the 9-volt battery What are the pieces that you have added Please explain the circuit and thank you
"This experiment is dangerous or even lethal, do not try to replicate at home."
haha
+Bruno when has that statement ever stoped people from doing stuff
+jamiepie123 it never happened,it just made people curious and made them recreate it.
+Bruno Who don't risk doesn't have anything.
a troll can't help you =_=
please tell specificly the materieals and the position of the materials
we're did you get the ac?
would such a low current still be noticeable?
Where exactly are the wires that go to the voltage multiplier connected? Thanks!
+Andrew G the diagram is on the video.
Where I buy this?
Hmm, an interesting experiment with this voltage multiplier. You say that you have nearly 10 kV voltage, is it possible to charge a HV capacitor with these high potentials ?
Can i use this one on fishing?
What components do you use in the video? Tell me very good video
Greetings! Sir...Did you change the transistor?
no
Gracias por responder...lo replique,pero la salida de alto voltaje no es tan potente como la tuya. logre mejorar el circuito bajando el valor de la resistencia que tenia en el emisor...saludos!
Can we store the voltage that is multiplied by voltage multiplier?
But does it zap bugs better?
Could you buil a spark gap transmitter?
what type of caps are you using another words what is the voltage of this caps? they must be atleast of 1000 volts each right?
carlos bison My caps are 3000 V 0.0018 microfaradas. The caps must be rated at least at twice the supply voltage.
what diodes and capacitors you use? please give me link where you buy it.
+Amir Haqeem diodes are 1N4007, capacitors are 1800 pf @ 3000 volt. Dont have a link
+Ludic Sciencecan i use this one? www.aliexpress.com/item/100PCS-1N4007-4007-1A-1000V-DO-41-Rectifier-Diode/32375456677.html?spm=2114.031010208.3.1.TiYY87&ws_ab_test=searchweb201556_2_79_78_77_80,searchweb201644_5,searchweb201560_9
+Ludic Science *can i use this one 🔝 ^
+Amir Haqeem yes
Does it matter what type do diode i use?
diodes have to be rated at least at double the voltage of the source
can i incoperate it into my fence energiser instead of ignition coil
& how about high voltage probe?
What is output voltage?
Which transistor does it has ?
unmarked
If I tried to run this in a sealed container for like, say, a day at a time to produce nitrates for my plants. It would overheat and melt, right?
the video shows that the capacitors are 0.0018 mfd (see at 1:18)
is that 'mili Farads?
Rolando dcd microfarads
Hi I have a question What is the code of the ceramic capacitor
+Kate Flow 182, 3kv
+Ludic Science Puedo añadir otra etapa al multipicador de voltaje ?
Si es asi, cuanto voltaje me daria la salida ?
Que tan peligroso podria ser ?
+victor morales si puedes añadir las etapas que quieras, cada etapa añade el doble del viltaje de entrada. Es imposible contestar a la pregunta de que tan peligroso puede ser, depende de muchisimos factores. ¿que tan peligroso es andar en automovil??? depende de muchas cosas. Lo mejor es tener siempre precaucion.
+Ludic Science gracias !... y de casualidad tu no tienes otro canal de youtube en español ?...tu voz se me hace conocida
+victor morales Si
Isn't the high voltage side of the original circuit a voltage multiplayer?
+Saikit Tang Yes only with more stages and larger capacitors
can i use in4007s instead of in4007?
Yea, but, where is the circuit diagram, components name and schematic?
does the voltage multiplier works with dc current
What transformer do you use to make the AC to DC? step up or step down
Can we use step down transformer as step up if the wire is connected on the reverse side?
Hello, how long can it operate assuming it stays on? I am assuming that the higher the output the faster the drain on the battery.
a few seconds only
Hi, won't the current from a 9V battery damage the components if it is used very often?
Viktor Božičević yes, continuous use will burn the circuit
is it high frequency? does high voltage like those in kilovolts has high frequency?
Can I add this to ignition coil high voltage output. I'm currently using as fence energizer
Will this power a Tesla coil?
Thanks for replying so quick!
Brother, what would hapen if we dont put a ground, does it matter.?
it's not dagerous this high voltage current is less than 10 milliamps.
Diego Bocchese it's still dangerous.
you right :D hahaha
fucking put a big capacitor in the output then you have your personal heart fibrilator/desfibrilator.
😂😂😂😂😂😂😂😂
no
I couldn't find any 3kv caps, would 2kv 1800pf caps be good enough?
+Andrew Tornadoboy if you use 2kv caps, use less voltage, 6v instead of 9
Can i use LED's instead of diodes. If not, do i have to use the ones in the video?
hama hamason Leds don't work. You can use any diode that has a rating of more than 1000 volts and more than 1 amper.
Ludic Science all i have for the capacitors is 5KV will that work??
hama hamason Yes
can i use this for my electrolysis of water will it work?????????
not sure, circuit is very low power
for electrolysis you need high current not high voltage as Faraday,s law of electrolysis tells us
Can it be done with polyester?
Yes but same or higher voltage
can i use a break cfl inductor as a transformer
Would you feel the output as it is high frequency?
+LASER BEAR ASSAULT UNIT In this case the transformer outputs high frequency, but the voltage multiplier converts that to pulsated DC. You will feel a very nasty shock
Oh the fun a $5 fly swatter and a few components will bring me.... :)
+Andrew Tornadoboy By the way, what kind of amperage does it have at the full 10kv?
+Andrew Tornadoboy around 10 ma
+Sharp Paul It depends... the most important thing is that the current does not pass through the hearth. For example if you take both terminals with one hand, you will be shocked on the hand only, but if you take one terminal with each hand, then the current travels from hand to chest to hand through the hearth circuit, and that may be deadly.
+Ludic Science but the current will drop dramaticly as it has to pass through your body which acts like a resistor, and i think i remember from somewhere that it takes 5ma directly across the heart without the bodys resistance to kill you.
+Ludic Science It will hurt but it won't kill you. A new 9v battery has about 1A of current. If you step up the voltage to 10,000 volts, the current will drop to 0.0009A or 0.9 mA.
You need about 70 mA to kill you.
Is it ok to widen the spark gap so that way I can have the switch engaged without me having to hold it down?
It would be nice to walk away and let the destroyer auto pilot without the arc being engaged the entire time.
Hi, i have now taken away the parts from the fly swatter circuit that you did. But in the video you take the powersupply and put the parts on another cuircuit. I cannot see how you build the circuit. Please help me.
What type of multimeter voltage multiplier probe did you use? I assume it's probably a 10X, what's the brand?
Can this be used in a Tesla coil with a spark gap?
you could try but it's unlikely as the frequency of this circuit is equal to the resonance frequency of the transformer's primary coil, which is way lower than a tesla coil's resonance frequency
What happens if you only have 4 stages on the multiplier?
where to find these capacitor
Thanks a lot for video. How can I make this power supply with 60 kV output with 220V AC input? Can you please help me which of your projects is appropriate for my purpose?
How did you decide on capacitor size? I have .0022uF caps would those work?
Matthew Lawrence the larger the capacitor the higher the output current. yes you can use that cap
Sir, it is okay to use the original battery of flyswatter? it still work the same? i just want to try it.
+junryl villoria it woks but the arc will be smaller
/Sir, What is the replacements for the capacitors and diodes? because there are no stocks available for 0.0018mfd, 3kv.
So how much voltage comes at the end of circuit... How much does it takes to make a spark?
+Karlo Matić around 10,000 volts. how much what?
Karlo Matić it takes 3 million volts to make a spark across 1 meter in air. So you do the math!
Don't those diodes (1n4007) look too small for 10kv arcs?
Current is very small hence you dont need fat diodes
Can I use this for powering a tesla tower
excuse me sir. can i have the specific list of the materials used ? i am planning to make a taser from this :)
You said 0.0018 mfd, is that microfarad or millifarad?
hama hamason micro farad
The first Stage make it DC right?
pulsating dc
Ludic Science OK thanks
can I use DC current for voltage multiplying.
+dawar jan No
Can i use 100nF Capacitors Please Tell?
And is it possible to make the voltage multipler longer and then convert that back to ac so it hurts more
James Huang you can make it longer anf get more voltage, converting high voltage dc back to ac is very difficult.
ok thank you for your response it helps me a lot, your videos are very inspirational and to convert it back to ac you can put it through a inverter circuit
James Huang Yes but inverters with high voltage input are very difficult to make and expensive to buy
Can you give me the diagram or scheme of the down-left circuit ??
Geology lover I do not have it. Try to google "electric fly swatter circuit"
If we're to do this with a multiplier with 12 stages what capacitors and diodes would I need
Michael Murphy the same as in video
Output voltage ?
watch video
is 22 uf ,3kv,cermic
capacitor will work ??
Uhm, is multiplying not going like 2, 4, 8, 16, 32 in this case?
No, each stage ADDS twice the input voltage
Ludic Science
Thing still confuse me that 1st stage output is 2 then as input to 2nd stage then it was 4 as output then as input to 3rd stage, it become 8 as you say in adds double of input
.
Unless you mean by it keep adding the voltage of original input in every stage.
Yes that is what I mean.
Could you please share the circuit diagram. I want to produce this circuit by myself, please tell which transformer are you using.
Hi ... yet another great video !
Is there a way that you can use this flyswatter circuit to light a bulb wirelessly with a coil ?
+Gabriel Engel That´s a good question. Not sure, need to think abut it. If I come up with something I will upload it,
+Gabriel Engel Interesting, not sure if the circuit really works. Looks to simple to be able to do that, especially with only 10 turns in the coil!!!! If I have ther ime I will try to replicate
Thanks again for your reaction:)
Sir does the flyswatter output (pulsating dc or ac) initial or you removed the high voltage sided components so as to get (pulsating dc or ac)?
+Pranal Ingle I don´t understand your question
Ok sir just justify why to remove those components on high voltage side. and also is the output of flyswatter circuit a pulsating dc.
+Pranal Ingle You need only the output from little transformer. Other components are not needed you have to remove. Output of entire flyswatter circuit is pulsed DC, not good for multiplier. Output from transformer is AC
Now it's clear Thanks Sir
That's so cool! Can this be used to ignite fuel?
do you still need the diodes for the discharge to be the same as when it was an electric flyswatter? im going to add a 10kv generator with 5 Metallized Film Capacitor 0.022uF 223J 2KV but dont know if i still need the diode for it to retain the original discharge elements of the electric flyswatter
the diode voltage must be at least 2 times the voltage of the source
Ludic Science so id only need the diode if i want to continue to step the voltage up? would i then want the resistor for the effect im looking for and if so what is the original resistor in the board? thanks for your help
But your using dc power not ac ??
have this set up powering a mini tesla coil, loads of fun from battery power. the coil itself is based on plasma channels 3v tesla coil. love the content Ludis Science, keep up the good work.
If I use a 4v battery instead of a 9v battery. Can a 6x 1nf capacitor produce those loud electricity?
what value of capacitors and type of diode u used here ?? i want to make exactly something like really need help . haha Thanks again. BTW, nice vid.
Ps . im not doing it at home im replicating it at a lab, here at the philippines. for a school project Tnx again
how do you make this kilovoltimeter ?
I've always had the most fun with a swatter circuit by adding five or six of the same capacitors paralleled into the output, it takes a bit longer to charge but the resulting explosions are well worth it. I usually take the paddle and grid off then attach two steel needles about 2 inches long on either side of the original handle and bend them inwards, so there's about 3/16" to a 1/4" of gap (4-6mm) between the tips. It becomes a bug _detonator,_ any insect caught between it's prongs become plasma vapor and little tiny bits of exoskeleton, the entire creature disappears in an instant. Safety glasses/squints are required🤣.
try adding them in series.
@@codeunited5905 that wouldn't work, or work very well anyways, the charge circuit only charges to 2kv, you would need to redesign it to reach the required voltage to max the caps out.
hey ludic i want to ask does it gives ac or dc voltage ? please quick reply
Gagan Sharma DC