How to Replace Chrysler Dodge Jeep 3.7/4.7 Valve Seals, Valve Spring using a Spring Compressor Tool
HTML-код
- Опубликовано: 29 авг 2024
- New valve spring compressor tools with metal reinforcement are available now!!!
Order from our shop using this link:
crunchysann.co...
For those outside America, order from our eBay store using the link below and select international shipping option during checkout:
www.ebay.com/i...
Description:
If you've ever tried to replace the valve seals or keepers on a 3.7L V6 or 4.7L V8 engine, you must've realized it's nearly impossible using other cheaper special tools.
Our special tool allows you to:
- Quickly and easily compress/decompress, remove and install valve springs, keeper and seals in a very controlled manner. You no longer need to strain your arms trying to hold the spring compressed while trying to install keepers.
- Allows you to keep the valve springs compressed for extended durations while you take your time re-installing and aligning the valve keepers.
- No need to pull your engine from the car. Just remove the brake booster as you normally would have, to access the rear cylinders.
Works on most early Chrysler / Jeep / Dodge 3.7L V6 and 4.7L V8 NON HEMI engines including:
1999-2009 Jeep Grand Cherokee
2000-2007 Dodge Dakota
2000-2009 Dodge Durango
2002-2007 Dodge Ram 1500
2006-2009 Jeep Commander
2007-2009 Chrysler Aspen
2006-2007 Mitsubishi Raider
NOTE: The tool you receive will be the metal-reinforced version, not the yellow piece shown in the video. They look and function the same way.
Description:
Fix blue fumes coming out of your Dodge or Jeep exhaust. If you've ever used the Dodge special tools to replace the valve stem seals or keepers, you must've realized it's nearly impossible to do this using those special tools while the engine is still in the car. Good luck doing this by yourself with only 2 hands :). I made the special tool in the video to allow you to not only remove the valve springs, keepers, and stems, but also re-install them all by yourself and can be done in a few hours.
Additional info:
- It's easier to use than the other specialty tool on the market.
- Works on most early 2013 and older Chrysler / Jeep Dodge 3.7L and 4.7L NON HEMI engines.
- You may need to temporarily move the brake booster out of the way to access the 2 rear right cylinders on a dodge ram.
- You will need to remove the rocker arms (a simple flat head screw driver is all it takes).
Keep in mind if this is your first time doing this repair, you'll need:
- To remove the rocker arms (a simple flat head screw driver is all it takes)
- Air compressor (at least 90psi)
- large plumber's wrench
- tweezers
- Magnetic pickup tool
- Vaseline or some gear grease
Link to Dodge Ram valve lifters:
amzn.to/2IW1U2Y
Link to Valve Cover gasket kit you should replace if you haven't already done so in the past:
amzn.to/2DJwMQT
Link to MOPAR Valve keepers (buy at least 4 since you may loose them)
amzn.to/2IXd87l
Link to Valve stem seals 20pack kit:
amzn.to/2IV1vxC
Update... i ordered this guys tool and Pierre got it to me by the 3rd day. The tool WORKS LIKE A FREAKIN CHARM!!! THANKS SO MUCH BRO and sorry i havnt posted review earlier ive been busy raising these kids and working on these cars. Youve saved me a shit ton of time once again THANKS BRO YOU ROCK 🤘🤙🤙🤙
Hey Pierre could u email me at apple.apeezeh@gmail.com when u get this bro
Can you please send me a name or place I can buy it from........4436533127 darius.........thanks
@@Crunchysann I need this please send information so I can order it.......4436533127 Darius
Where can I get this tool
How hard was it to get to the rear ones
My husband used this tool to replace valve seals on my Jeep Liberty. He began using it but after trying to remove the 5th one the bolt would not move it was stripped and he was unable to remove it after trying different ways he ended having to use a hacksaw to cut it off carefully. We were so upset & dissaponted so I emailed CrunchySann and told them what happened. They replied next day. We expected tthis conpany to give us a hard time, however, to our surprise they immediately sent new one. We were so relieved. Once received my husband continued the job, however, this time he was very careful using it slowly and used graphite on the bolt between every 2 valve seals removed. We are excited & relieved that he was able to complete the job & now I have my car back thanks to the great customer service this company provides. I absolutely recommend this tool as this company stands 100% behind their product.
Thank you for your honest feedback Mary! We're glad that your car is back on the road.
Is he willing to sell the tool?
Just used this today, and it FREAKING. WORKS. SUPER. WELL. If you have to take the valve cover off for any reason, might as well get this and do the seals. 100% recommended
Update! Ordered the tool last week along with 16 hydraulic valve lifters. This thing worked like a charm! No issues whatsoever. No more blue smoke or lifter rattle. 100% recommended! Thank you!
Thank you very much for the positive feedback! It's great to know our customers are successfully repairing their vehicles with our products. Stay safe out there!
I was in the process of designing a valve spring removal tool for my 4.7L Ram 1500 when I came across your video. I ended up making mine very similar to yours and I can confirm that it works perfectly. I used PLA as that's all I had. 30% infill with 6 upper, lower and side layers for the main part. For the cylinder shaped part, I originally did 30% infill but that was insufficient and bolt started crushing the PLA inside the hole. I switched to 100% fill. Material usage increase was minimal and it only took another 10 minutes to print since it's such a small part. Not a single bit of crush after that.
My truck has been burning oil on start up so I figured it was the seals. Sure enough, the seals weren't even touching the valve stems anymore. I completed the passenger side yesterday and will continue with the driver side today. This tool made removal and installation a simple one man job.
I'm replacing all the lash adjusters while I have it apart. The upper adjusters were all good but the lower ones were all collapsed. Not sure if this is just an coincidence or if it's typical of this engine.
@@Crunchysann If I cannot print it, do you ship ? how much would it cost?
Was hoping you sold the tools AND YOU DO! WILL BE ORDERING WITHIN THE NEXT 30 MINUTES THANKS MAN 🤘🤙🤙🤙
@@Crunchysann i was able to order it with the last link bro and it went thru. Under a Jauhara. Said est. Delivery is on the 25th. Also i didnt see option for faster shipping option is there one that could get it to me by tge weekend? And ill definitely post an update, i absolutely was planning on pulling the heads til i saw the video 🤣😂🤘🤙
@@Crunchysann salud 🤘🤙
@@Crunchysann i was looking for the design on thingiverse and it's not their no more can share the design again please?
hi crunchy , big hello from Moruya Australia, i purchased your new valve spring tool and it works very well and is well made, it was fast shipping and just want to thankyou for taking the time to make this tool and provide an option for other home mechanics , have a good one .
Ah thank you so much. I was excited when I saw you 3d printed a tool. I'm familiar with 3d printing but no longer have access to a printer. Seeing the ebay link really made me happy. I purchased one on ebay and cant thank you enough.
Ordered mine. Thank you.
@@Crunchysann I got it. Works great!
In the midst of replacing valve seals, springs, rockers, lash adjusters on my 03 Durango. Tool is well made. This is not a quick job. Follow the technique in video for getting valve locks on. If you have a 1st gen Durango, accept the fact that the power brake booster is going to need to come out and do it before you start on the driver's side.
hi I'm currently trying to do this on my 02 dodge dakota with the 4.7 and I looked up your tool and couldn't find it. I just got it all tore apart and to find the same problem you did was wondering if you had any of these available or how soon you would be able to and how much they are. because this is my daily driver
Dude I love the video. But if you sniffle then click your damn lips one more time im gonna rip my ears off
I'm going to the shop and make me one right now.
Thank you. Haven't seen that tool yet. Very nice.
Will you be printing anymore of the tools? I checked out the link's and it's out of stock on both.
I'd really like to buy one or two of these when you have them in stock. Are you still making these?
Yes me too
any have used one NOT using any more to sale it ?? i have 03 jeep liberty need to do too does not want buy new if only need to do for one a while
Is there an STL available to print this myself? Thanks!
Going to order one. What did you use for removal of rocker arms?
@Keith did you ever get an answer? I'm literally at this point and he never mentions it in the video!
@@Crunchysann Thank you sir. I will be ordering one of your tools this weekend.
An open end 10mm wrench with a 90 degree bend at the end works perfect.
Purchased tool. Going to be replacing valve seals. Thinking of putting in new rocker arms and lash adjusters while I'm in there. Engine has 170k miles. Thoughts?
@KEITH Don't forget to change your valve cover gasket and valve springs.
@@Crunchysann I have new gaskets. You changed the valve springs as well? I was going to reuse
@@keiths9483 it's not required. But at that mileage and given the amount of things you need to take apart...I'd change them.
@@Crunchysann What valve springs did you use? Mine is an 03. All stock. Did you also replace retainers and locks?
@@keiths9483 springs vary, i would advise you to call the dealer and identify the exact part yours takes. I only replaced retainers that i lost during the installation.
I'm assuming this would work on the 3.7l jeep liberty as well, correct?
The website says youre out of stock. I would like to purchase 2 as soon as you message me back.😎
video is good but sniffle is annoying af and clicks
nice video i just ordered the tool thanks
Hi colleague! here Leo from Venice. I have your same problem, but fortunately your resources too. Would you be willing to share the .stl file with me? great video, thanks!
Can these all be replaced engine in car on 3.7 05 grand Cherokee without removing heads/anything but rocker covers?
yes
Hi looks like great tool
Can I purchase one and send to Australia
What’s best way to purchase as eBay showing none available?
Can this tool be used with the rope method ? I plan on using rope since I don’t have a good air compressor .
Yes it can. The key is to make sure the valves are not able to move once you start compressing the spring.
It works like a charm!! I used the rope method instead of the air. Like you said. I just made sure the valves don’t start to fall as I compress the spring.
@@guswendt glad to see another happy customer!
Who ever buys that tool, holy shit 125$? I feel bad for you suckers. Online the same type of tool for a 3.7 and 4.7 Chrysler engines just built different and looks different and about 90% of the cost of this one... It does the same thing, cups around the camshaft and presses down the valve springs, all you use for this one is your regular socket wrench hooks to the side and as you apply pressure it compresses..... This one also comes with an attachment to make it a rocker arm remover. 👍
The main difference with our tool is the fact that you can easily use our tool without having to remove your entire engine from the car, all by yourself. It will not slip and fly off like the lower cost tools you mention. Our tool holds the spring compressed so you can use your hands to add/readjust keepers: Try doing that with any other tool designed for this job on the engines you mentioned, while the engine is still in the engine bay :). We do still appreciate your feedback.
This is true but and I have one but is impossible to do the back cylinders with the cheep tool. There is no way with the cheaper tool to put the keepers in and hold the spring down at the same time.
Will these be back on the website soon? Project sitting and waiting. I have registered but no contact portal on your website.
I search and search on ebay and cant seem to find your specific tool can you steer me in the right way to buy this tool.thank you ...
@@Crunchysann Your link shows 259,909 Results to try and find yours. Will these be back on the website soon? Project sitting and waiting. I have registered but no contact portal on your website.
@@Crunchysann I used your link on eBay and it did not pull up your product it pulled a screen full and at the top says 259,909 results for your tool. Page after page of tools.
@@Crunchysann yes
I tried to purchase the tool via eBay and the site but it looks like your sold out anyway I could get one?
Thanks!
Hi, we’ll have more in stock soon.
@@Crunchysannhow soon are you thinking? Thanks!
I’m midway into the project and the cheaper option has shown to be very ineffective
Went to buy tool but says not able to buy because link or item removed
Does the tool fit to replace seals in the back?
Any discount code
Im trying to find one for myself
How do you turn the camshaft so that the tool fits around the lobes?
remove all spark plugs, and use a large wrench or ratchet to manually turn the crankshaft bolt.
says the tool is out of stock on ebay. will the tool be available again soon?
It's back in stock.
I don’t understand what the compression at 90psi is for?
To keep the valve from dropping.
Hi mate your tool is no longer available on eBay is it possible at all to still purchase one from you thanks?
@@Crunchysann thank you, your a champion
Where can I buy this tool at?
@@Crunchysann thank you!
Looks like it’s 3D Printed. How much for the 3D printed files?
Hi Zachary, although some parts are made out of 3D printed plastic: The metal supports add more than enough rigidity to this tool for the job. Unfortunately we do not provide the 3D models.
Are you still making these I could really use one
yes, they available on crunchysann.com
I’d like to order one if possible?
It says the tool is out of stock. Are you getting some more in soon?
We are currently on backorder. The current eta end of october.
@@Crunchysann Thank you for the reply. I got a 2005 GC that smokes like a cigar. I'll check back in a couple of week. Thanks.
If you send us an email at support@crunchysann.com we will send you and update when they are in stock.
anybody know if these are anywhere to be found? USED or NEW
Hi, these will be back in stock by 11/18/2022. You can order directly from our website www.crunchysann.com
Do you still sell this tool? The Ebay link says it is no longer for sale.
@@Crunchysann Cool just let me know when it is back for sale and a link please. Thanks
How good does it fit on the last cylinders in the back
Fits very well as long as you remove the brake booster.
@@Crunchysann the brake booster on the 2008 Grand Cherokee 3.7L? I just replaced the brake booster and it was a pain in the bu** haha!! I was going to do the valve seals with your tool but now I have second thoughts lol. The grand Cherokee seems with enough space not to have to remove the brake booster…!?
How do I buy one shows out of stock.
We are currently on backorder. The current eta end of october.
Where can I buy this tool
Hey Pierre bro shoot me a link so that i can buy another one mine got lost maybe six months after i fixed my Ram and now i have another Ram that needs the stem seals thanks in advance bro and hope all is well 🤙
I found the link weeks ago and recieved my order in just a few days bro thanks
@@Crunchysann worked just as good as last time man thanks and im glad that i got two this time. Now i have 3 because i found the one i misplaced 🤣🤣🤣🤙🤙🤙
Anyone have the stl by chance??
Where can i order this tool?
I really need it
Hi, these will be back in stock by 11/18/2022. You can order directly from our website www.crunchysann.com
Will this work on a 03 jeep grand cherokee
@@Crunchysann I can't get this video to load and it appears this is the only video doing it. It also happens to be the exact video I need fml. Is the video corrupted or removed?
How can I order one of these
Hi Charles, sorry about the late reply. RUclips notifications are very slow. Here is the link to our website to order. It’s also in the description.
crunchysann.com/BL/product/2-pack-chrysler-3-7l-4-7l-dodge-jeep-valve-spring-stem-keepers-replacement-tool/
Where did you purchase the tool?
crunchysann. com
Is it possible to ship this tool to Poland ?
Hej moze bysmy by sie złożyć na takie narzedzie na połowę było by spoko
How can i purchase this tool?
crunchysann.com/BL/
How and where do I order this from?
crunchysann.com
How do I order one. Thanks
Hi, the link is in the video description
Shit pekło przy pierwszej spreżynie po skreceniu na wkrety jeszcze dwie obsłużyło z drewna by lepiej sobie dało rade
@@Crunchysann plastic ale pekło po pierwszej spreżynie wiec chciałbym zwrot pieniedzy
@@grzegorzkrasucki7214 hello, please send us an email at support@crunchysann.com so that we can help resolve this matter. Thanks.
Sorry bud...my attention span is low and you take very long to explain and work...gonna check another channel.