watch out !! using a angle grinder||how to mount a cutting disc onto an angle grinder correctly
HTML-код
- Опубликовано: 4 ноя 2022
- using an angle grinder must be very careful and vigillant, as it can be very Dangerous. here is||how to mount a cutting disc onto an angle grinder correctly||how to install a Cutting disc in an angle grinder||instally the cutting disc and using the angle grinder
Although it is a good practice to keep the disc face with the printed label downward and tighten the nut on the plain side, but it is not advisable to tighten by gripping the disc. Reason for keeping the label side down is to avoid the emery surface damaging the bottom plate. Always use the supplied wrench and by holding down the lock on the back side. Similarly always use the wrench to unscrew and always remember to remove the cutting disc after use. Otherwise there is every possibility of the disc getting damaged.
As mentioned by some others never use the machine without the guard and safety goggles.
Thanks.
Thanks sir🙏
I throw away the wrench tool and just hand tighten the disc, never had a problem, it is obvious you don't use a angle grinder every day!!
For disc cutting , just hand tightened slightly. The rotation will create the force that tightened the nut. But dangerous if twist / change direction when cutting.
But if sanding mode ,no harm done if hand tightened.Those but will tightened itself too
Very dangerous using wood saw blade on non trigger switch
What a load of bollox!!
Hahaha!
After seeing so many replies on the subject I remember this small write up;
He Knows not and he Knows that he Knows not!
You can Teach him.
He Knows but he Knows not that he Knows;
You need to awaken him.
He KNOWS and he Knows that he Knows!!
He is the Wise one and you can follow him.
However now comes the Dangerous one???
He KNOWS NOT AND HE KNOWS NOT THAT HE KNOWS NOT,'Oh! What a pity.' Always avoid him.
(I am from India and we have a saying, when translated it means,'It is enough to give just a Clue to the Intelligent person'.)
Thanks.
cutting disc position is not important,don't use grinder without disc guard. Best practice don't remove disc guard anytime,you can adjust disc guard by lossing screw and turning your hand.
Yes..thank you very much sir🙏🙏
Absolutely correct 👍
But disk gurd prevents the use of Standing wheel what to do for that ?
For me remove it or not the disc guard i dont care because im immortal
@@trickswelder3839 but you hold the machine wrong way, you have to hold the machine, like these dust going to front side ... but your holding system to dust throwing to your side.
One of the most important issues of using an angle grinder is the disc itself. Do NOT buy cheap discs! The cheap disc will break very quickly and at 10,000+rpm any small object flying out is deadly and without the safety guard the risk increase by x10.
😢
Always a good idea to check that the machine is disconnected from the power source (unplugged or remove battery) before installing or removing blades. And use the safety guard!!
Ok, thank you
no no this is wrong 🚫
must need to use safety guard for angle grinder
Thank you🙏
ਬਹੁਤ ਵੱਡੀ ਜਾਣਕਾਰੀ ਮਿਲੀ ਹੈ।
22 price kiya disc da dasi yaar❤
No guard no gloves no face shield wow you the boss 😅😅😅
Today only I purchased one ancle grinder. Your demo will be very useful to me. Many things (every thing) come to know me. Thank you very much sir..
Do not follow the video unless you want life injuries
this video help me to demonstrate during my welding class. thanks alot.
Why don´t uses the security guard and the handle bar? Security first
بسیار متشکرم از آموزش خوب شما و نکات مهم که در این ویدئو آموزشی ارائه دادید......موفق باشید
🙏
Unsafe because you forget to put or to install the grinding desc guard
Thankyou
I bought a new grinder and it's my first time.. so thank you for the tips.
Thank You
Very good👍
I had a lot of old pipes and rebar to cut up and from what I read ruclips.net/user/postUgkxPDBfLu68o58Aw85O_J-zIFfjJARBhp-3 this would be the tool for the job. Since I had never used one, I watched a couple of youtube videos and I'm so glad I did. Some really good safety tips, which I followed, and this tool did a splendid job. One good thing to know is the weight of the tool puts just about the right amount of pressure on the metal I was cutting, so I didn't have to use a lot of pressure, which is more likely to jam the tool. It made fast work of my job.
I used portable grinder big and small,sence 1978 until now ,but l make my own cover design if using the cutting disc, the original cover if l used grinding disc. I never meet accident if the disc is broken...Safety First Always...
Oh my bro... Disc guard is very important. Safety is number one.
Ok.. Thank you🙏🙏
Para que sirve el protector del disco y el mango para sujetar que trae la amoladora, por algo lo puso el fabricante.
Thank you sir🙏🙏
Never uses that dangerous tool with a single hand. Bad video
Silently useful. Thanks.
We had an accident while using the grinder. The disc broke and the pieces flew everywhere, sadly my dad was hit on the shoulder. He had 8 stitches. Safety first, put the guard on and wear protective gears. I know it's hard to grind if there's a guard attached but safety is the priority. You'll eventually get used to it.
Ok.. Thank you very much sir🙏
The thin wire (Fibre thing) inside of it is scary as fck. Safety first
Great content !
You're soooo smart! You are my hero!!!!
модель очков мне понравилась )
стиль 1970 ых сейчас в моде
Thank you Sir 👍👍
great tips.
Mainly one wrong from you, must be use blade guard when cutter using.
Correct! Blade guard must be installed as protection incase the blade shattered...many don’t understand that safety...
Unsafe practice of using angle grinder....
வாழ்க வளமுடன்.nice working video
Thank you
Jamais usar sem a proteção da máquina.
Ok. Thank you very much🙏
Very dangerous to use without blade guard.
If blade brakes the flying parts can inflict fatel wounds
thank you
Segurança em primeiro lugar.
Ok... Thank you sir
good, thanks for share
Thank you very much🙏
Thank You.
Thankyou very much🙏🙏
Wihtout gard hataka
Ok thanks 💗
without angle grinder' s safety disc
guard ?
Good day Sir,
Pwede po ba yung ordinaryong cutting disc na may butas na m10 sa angle grinder na may thread na m14?
No
Legends not use disc Guard❗️😂😂😂
They are ready to stich body part❗️😃
Thank You
This is totally against the law of using.disc should turn over to prevent split,spinning should spin against the tightening screw to prevent losen.this you are right.disc guard is vital.
🙏
Good
You will find that most people who use the grinder a lot have removed the guard. I think all the reasons for this can be summed up by saying the guard makes using tool very frustrating, So for these people (like me) it comes down to a matter of either avoiding the tool or using it without the guard. Also when the guard is on, I hate that I cannot see where the entire wheel is at all times, which makes me feel uneasy. For similar reasons, I take the guard off other power tools like the circular saw and table saw. I actually feel safer with the guard of and having the ability to see what the whole blade is doing. Lastly, I feel the direction of the grinder cut-off wheel is a major safety issue, because if it's in correct, the wheel can suddenly get full traction sending the whole grinder toward you while it's still spinning.
🙏
Till it comes off shatters.
Then you will understand the reason for the disc guard
You prefer to use it without disc guard but you should not spread any unsafe condition to the other persons which may cause severe injuries!!!!
How can you be safer without the guard, that's the main purpose of the guard, to make you safe, not the other way around. I've been using power tools and especially an angle grinder for 24 years now, I have no issues with the guards, it protects you, bro!
The first thing I do when aquire a new grinder is throw away the guard and the handle.. 40+ years without an issue..
Good your channel
Thank you very much🙏
Nice to the point information
🙏
Why no disc guard?
This is called how to loose eyes or faces cutting No Guards... very nice cozzyy
Good job
Guard & handle are missing. Consider readinģ the disc label as it indicates the expiry date of the disc & its rate (rpm). The disc rpm should be higher than the machine rpm.
Ok.. Thank you very much sir🙏
Thanks bro
Thanx for the info! I did not know that. Any reason why that is? I guess you have to be extra carefull with those blades if you do not have a disc guard...
🙏
No, he actually montage disk wrong, he didn't use safe guard, and didn't use side handle!! the dump user try learn safe use grinder....that a crime!
@@KallenSC I meant it partly sarcastic ;-) But i guess in an accident, you rather have the grinder run away from you, as opposed to towards you when cutting. Downside, you have sparks flying up your behind...
Always use safety eye glasses while grinding. 👍
Wery clever instrukcji👍👍👍👍👍👍👍👍👍👍🙂
🙏
Perigoso as proteção das máquina fundamental não se deve tirar foi projetada p segurança total
Where is the grinder guard?? and your gloves????...good to see you have utilize your eye protection.
I have often seen welders not using disc guard. It is dangerous without disc guard. My disc broke 2 times during use. Luckily i was using disc guard and broken pieces of disc didn't come towards me.
Ok. Thank you
Thank you for this video I been doing the other way you showed not to for years had disk grab and catch explode cutting and turning with disk facing you makes sense pulls itself threw great video
Thank you
Und wo ist die Scheibenabdeckung bzw. der Handschutz? Ich selber hab mir schon mal geschnitten.
Thanks sir
A Mechanics Adventure
Why manufacturers don't make clear / see thru guards??
Please wear safety hand gloves and don't forget to wear glasses too. Thank you.
Ok.. Thank you very much🙏👍
And dont forget a dust mask....the dust generated can and does affect your lungs......I know first hand
Saya sllu pakai yang cara no 2 sir 🤝🇮🇩
Ya, Terimakasih
Valami még hiányzik. A szikra vezető burkolat, ami megvéd ha véletlenül leszalad a gép az anyagról. Ha megmutatsz valamit akkor azt helyesen tedd meg.
Thank you sir.. I have fixed it in the next video🙏
You are very wrong from the very beginning my friend! Guess what's missing? 😂😂😂
Sds-Clic is handy, doesn’t need additional tools to mount the disc.
Thank you for your video, it's great to know how to install the disks. 👍
Nice 👍
It seems you forgot to install the most important safety feature .... the disc guard !
Thank you sir, for reminding 🙏🙏
Welcome to third world countries... who's needing disc grinding guards... they think take tooo much time take it on/off. Ohhhhhh wait one minute saved your life eyes and face disc spinning 3200---6500 RPM...ahhhhh
No disc guard ! That’s the correct way to use the grinder for sure !
🙏
Thank you
🙏🙏👍
I think it is wrong placing of disc it should be inverted to loosen easily
You must use the key to tighten the disc and the disc guard must be in place before operating/using the grinder.
Thank you sir
.....And even handle to minimise shok in case the grinder kick back.
🙏
I'm ok on how you install the disc but on matters of safety it's very dangerous not to use the guard✌️
Wear is the safety gard?
Salamat Po sir sa live nyo
🙏🙏👍
the rotation arrow of the disc has its purpose.
👍
Good thank you
🙏
Throw away disc guard
cutting & grinding weel washer upon side very safety
RUclips seems to be full of these self-proclaimed "experts". You're correct about the orientation of the disc but why are you doing everything without a guard? FAIL!
Ok. Thank you
very good information
Thank you sir🙏
Friend, put on the protective cover of your angle grinder!
Yes sir... Thank you very much🙏🙏
thanks sa tip
Thank You
Mester,hol marad a védőburkolat?
Thank you sir, I have fixed it in the next video 🙏
It is unsafe to use the grinder without a disk guard. Always tight the disk with the provided key/ tool, not your hand.
Cutting disk and the like have the arrow ➡ to indicate totation direction, always observe and follow that.
Thank you, sir
wrong the washer allows the mounting nut the ability to remove abrasive disc if the blade gets jammed
Thank you sir
That's just your thinking.
Cutting disc. Quality and date of expire. Watching. Or. Grinding mission. Amber. Disc amber. Calculated. Safety guard very important. Dead man switch. Cutting wheel removing key. Any time inspection after you're. Full. P P E. Chaking..... After Start you're working...
Unsafe bec. You forgot to install Safety cover and hand gloves , maybe u dont also use eye protector
🙏thank you
Guard lagana bhulgaye kya . No safety
Even the elementery school boys,understanding this way...lol..
🙏
Think Safety Work Safely ✅
Ok.. Thank you sir🙏
POR ESO PASAN LOS ACCIDENTES SIN EQUIPO DE PROTECCION PERSONAL
🙏thank you very much
Correct way is not removing the guard
Thank You
TU EQUIPO DE PROTECCION PERSONAL Y TU GUARDA EN EL EQUIPO
Thank you sir🙏
What happened to the wrench used to tighten the disk?😊
It is next to the disc guard ;-)
use the wrench ,it will not tighten because of the rubber bushing
@@josephjojoneri9329 Wrong..
@@josephjojoneri9329 It will tightened itself die to forced rotation. Done this hundreds of times. No force is needed. Just tightened slightly. Only for experienced users. For Newbies, please use guard shield. I've seen idiot Newbies broke the blade less than 10 secs. Cut softly and don't change direction.
@@rohzpopper4922 i am 58 years old, i am an electrician more than 25 years, anybody have way's, be careful and safe , thank you
Кольцом к верху надо граматеи
Good👍
Thankyou🙏🙏🙏
Protectector Guard Lagao
Common boy, You did not yet experienced a broken cutting disc that smashed your part of your body that's why don't install the guard while you work or use.
🙏
Cutting disk position is important and that sticker is danger that not properly stick it damage ur hand . First u must cheque power on button then plug and on.guard must for safety
Ok.. Thank you very much sir
nice
Bạn chỉ quá tốt.
Cảm ơn bạn.
👍👍👍
🙏👍
Safety Guard haihi nahi aur Right bta rhay ho
Dono process wrong hai
Thank you🙏